ACTFIRE BT-0909 Electronic Hearing Ear Protection for Range User Manual

USER MANUAL
READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING

COMPONENTS

1. Padded headband
2. Battery compartment
3. Headband wires
4. Guide arms| 5. Turn on /turn off controls
6. Two microphones
7. Audio input & micro-USB charging
8. Bluetooth controls
---|---

Installing Batteries:

Install two 1.5V AA batteries or optional Alpha 1100 rechargeable battery pack as shown.
Replace the battery door top-end first.

Note:

• Do not mix old and new batteries
• Do not mix alkaline, standard, or rechargeable batteries

Charging Battery Pack: (sold separately)

( NOTE： The batteries must be Rechargeable Batteries.)
Insert the micro-USB connector cable into the micro-USB jack. Connect the other end of the cable to a USB power source to begin charging. The LED will blink when the battery pack is charging and turn solid when charging is complete.

Power and Volume:

Press and hold the power button for 3 seconds to power the ON/OFF headset.Voice Assist will announce “Power ON” or “Power of.”
Adjust the ambient volume using the UP and DOWN arrows on the right cup.
Performance is best when the volume is set to the lowest level needed for conversation

Fitting Headset:

Fully extend sliders and place cups over-ears so that microphones are facing forward.
Then, tighten the headband using sliders.

To reduce the risks associated with harmful noise:

• Always wear hearing protectors when you are exposed to noise.
• Ensure hearing protection is properly fitted. Follow any fitting instructions included with this product.
• Do not bend or reshape the headband as this will cause a loose fit and sound leakage.
• For best protection, the ear cushions should seal firmly against your head. Anything that interferes with the seal, such as long hair (pull back to the extent possible), thick or poorly fitting eyeglass temples, pencils, or caps, will lessen the protection.
• Do not immerse in water. Clean with a damp cloth and mild soap. Do not use harsh or abrasive chemicals.
• Earmuffs must be regularly inspected for cracks or worn parts and for proper fitting. Replace as needed.
• only: Do not change between “Dosimeter ON” and “Limiter ON” settings during a single workday.
• Do not store the hearing protector in direct sunlight or at a temperature above 131°F (55°C)

CAUTION

To reduce the risks associated with chemical exposure and fire:

• Do not store the batteries installed. A leaking battery may cause bodily injury or damage to the hearing protector. The WEEE logo (shown at the left) appears on the product to indicate that this product must not be disposed of or dumped with your other household wastes. You are liable to dispose of all your electronic or electrical waste equipment by relocating over to the specified collection point for recycling such hazardous waste. Dispose of components in accordance with all applicable local and governmental regulations

NOISE REDUCTION RATING (NRR)

EXAMPLE

1. The environmental noise level as measured at the ear is 92 decibels dB(A).
2. The NRR is 24 dB(A).
3. The level of noise entering the ear is approximately 68 dB(A).

The NRR for the Wireless Electronic Hearing Protector is 24 dB(A).
Improper fit of this device will reduce its effectiveness in attenuating noise.
Consult the enclosed instructions for proper fit.

SAFETY INFORMATION

FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) this device must accept any interference. received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15.
FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
ISEDC Warning
This device complies with Innovation, Science, and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Operating specifications

Item| button| The key name| effect of action| Prompt tone/voice| indicator light| others
---|---|---|---|---|---|---
1| On, Off| power button| Press and hold the power button for 2 seconds to power ON/ OFF| Power on Ambient listening mode/Power off| |
2| Bluetooth symbol button (in the center)| | I.Press and hold the power button for 3 seconds to power ON/OFF| Bluetooth model connected| 1. Factory state: red and blue &eh, 2Hz cycle| Enter pairing mode automatically
2. Connection mode: blue flashing, 1Hz cycle|
Bluetooth power button-| 2. Press and hold
the power button for 3 seconds to power OFF| Ambient listening mode
3. fame mode: red ‘belling 1Hz cycle|
3| Answering up| 1. When a call comes,| rings| | Auto-pauses music and broadcasts ringtone when playing music
dick to miner or hang-up during a call.
4| 2. When a call comes in, press for 2 seconds to reject the call| Play the reject.
notification tone| music and broadcasts the| When playing music, it automatically pauses the
ringtone, and resumes the music after being rejected successfully
5| | | | When in the pickup mode, reduce the ambient sound volume to -20dB, and
resume the original
volume after hanging up or refusing the connection
| |
7| Pairing Your Headset and Phone| Press and hold the power button for 5 seconds in Bluetooth shutdown state to enter the pairing state| P.n.’s on| Red and blue flash, 2Hz cycle|
8| Matching success| Connected| Blue flashing, 1Hz cycle|
9| Play Pause| Turn on the phone player dick Play then dick Pause| | |
10| The next song| Click 2 to proceed to the next song| | |
11| In a song| Click 3, back up the last song| | |
12| Volt+| Volt—| Click step, level 5 with mute| Play the prompt tone when the volume is maximum| | This button only controls the ambient sou
the volume,
and the Bluetooth volume needs to be controlled through the mobile phone
13| Vol-| Vol-| Click Step Back, level 5 with mute| . Play the prompt sound when the volume is minimum|

How to contact us

|

@Actfire

---|---
|

@ACTFIRE

|

actfirestore@hotmail.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>