ASN AS-2021 Robotic Pool Cleaner User Manual

June 14, 2024
ASN

ASN AS-2021 Robotic Pool Cleaner

Important Precautions

  1. In order to avoid any accident/damage, it is strongly recommended to fix the power supply unit 3.Sm away from the swimming pool by using the safety rope (included in the package).

  2. In order to prevent severe damage to the cleaner, never power on the unit when it is outside of the swimming pool.

  3. The power cord must be connected to an appropriate earthed socket.

  4. Hold the top handle when putting the cleaner into water or lifting out of the water, do not pull the cable.Before power on, make sure to empty the trapped air inside the cleaner (no more air bubbles coming from the cleaner and the cleaner is fully submersed on the pool bottom).

  5. Before power on, make sure the filter be assembled in position and cable be fully released to avoid any winding, which could affect the cleaner’s performance or cause damage.

  6. Please clean and wash the filter bag every time after use.

  7. The cleaner should be stored in a cool and ventilated place, away from direct sunlight when not in use.

  8. The power supply unit should be placed in a shaded area during working. To avoid overheating and potential damage of compo –
    nents, never cover the power supply unit.

  9. Only authorized after-sales service personnel should open the cleaner’s power supply unit and motor assembly, otherwise the warranty will be invalidated.

  10. Do not use the cleaner beyond the working environment/conditions stated in this manual.

  11. Make sure the PH of pool water is between 7.0-7.2.

  12. This machine is to clean the pool only not for other purposes. Read carefully the user manual before use.

Attention
When put the cleaner into the water please hold the top handle make sure to empty the trapped air inside, then the cleaner can immerse into the pool floor.

ASN-AS-2021-Robotic-Pool-Cleaner- \(1\)When pulling the cleaner out of the water, suspend the cleaner above water for about 10-15 seconds to empty the water inside. Please holds the top handle only, never pull the cable. ASN-AS-2021-Robotic-Pool-Cleaner-
\(2\)

Introduction

The robotic pool cleaner AS-2021 is a new type of highly efficient and energy- saving swimming pool cleaning robot. Through its advanced computer-controlled program, it can clean the pool walls and bottom automatically. At the same time, it filters the pool water and gets rid of suspended particles without replacing the pool water. It’s totally environ­mental-friendly.
For safe operation, the cleaner works on 28V direct current. Please read
this user manual carefully before use.

Safety

  1. Power supply unit position
    • The power supply unit needs to be placed in a proper position to reach the distal end of the pool for the cleaner, meanwhile at least 3.Sm from @ pool edge.
  2. Free Safety Rope Comes with Machine
    • Please use the safety rope to fix the power supply unit, which can avoid the power supply unit drop off your pool.

Specifications

Rated input voltage 110V AC (120V AC)
Frequency 60Hz
Output voltage DC 28V
Power 150W
Cleaning cycle 1/2/3h
Filtering capacity Appr. 3963gal/h (15 M3/h)
Filter density 180microns
Moving speed Appr.33ft/min (10m/min)
IP grade Cleaner: I PX8; Power supply unit: IPX5
Max. water deepness 8.2ft (2.5m)
Working environmental temperature 50°F – 95° F (10-35 °C)

Operation Instructions

Panel

No. Indicator Description Function
ON/ OFF Power on/ off
  • Press this button, the cleaner starts to work;
  • Press a second time, the cleaner is off.

2| CYCLE| To choose working cycle| When the cleaner is on, use this button to choose preferred working time.
3| Indicator| Indicator| lH flashes| Working time of 1 hour
2H flashes| Working time of 2 hours
3H flashes| Working time of 3 hours
lH, 2H and 3H flash together| Working cycle finishes
| Fault Code| Meaning| Suggestions
Fault| lH and 3H flash with warning sound| Power supply overload| Stop the cleaner, check if anything is blocked in impeller or in transmission system

Filter Cleaning

  1. Slide the two clips according to the indications on the top cover to open it and take out the filters.
  2. ASN-AS-2021-Robotic-Pool-Cleaner- \(6\)Clean the filters.
    • Re-install the filters, pay attention to the good position and slide the two clips to close the top cover.ASN-AS-2021-Robotic-Pool-Cleaner- \(8\)
  3. Foam Installation
    • Attention : If your robot is in good performance, please ignore this instruction.
    • The following illustration is limited to the use of white foam blocks to increase coverage when the cleaning machine cannot completely clean and cover the pool table(Figure 3)
    • Stick two foams on the reverse surface of top cover (see below picture), make sure the two foams are in the middle part of top cover. ASN-AS-2021-Robotic-Pool-Cleaner- \(9\)
  4. Roller-Foam
    • In order to ensure the performance of the machine for the first time use, it is normal and all right if the two rollers of the machine are
      wet at your receipt of the robot. And it is recommended that before each use, if the rollers are dry, please immerse the machine into water for 15-20 minutes and wait for the rollers to fully absorb water, then switch on. (Figure 4)

Packing list

Item Name Model Quantity (pc) Note
Cleaner Cleaner AS-2021 1 In Carton
Power supply unit AS-2021 1 In Carton
Manual and safety rope AS-2021 1 In Carton

Trouble Shooting

Remark: The pool water conditon must be within the following parameters

  • PH :7.0-7.4
  • Temperature : lO·C(S0·F) to 3S·C(9S·F)
  • Salt : Max 5,000 ppm
  • Chlorine: Max 2 ppm
Symptom Possible reason Corrective action
Cable twists or coils up Cable not fully released Unplug power line and

release cable
Obstruction in pool| Remove obstruction in pool
Stuck on main drain outlet of the pool| Turn off pool filter system
Long time working| Release manually
Robot does not reach all pool area| Power supply unit improperly positioned| Place power supply in proper position so that cleaner can reach all area
Algae in pool floor| Before using Optimus at the beginning of the season you should brush any algae from the floor and walls of the pool
Customized pool shape| Ideal pool shape for Optimus is ROUND/ OVAL/RECTANGLE/KIDNEY SHAPE, please put the robot onto the position that need specific cleaning

  • Pool filter system and pump open
  • Cable not long enough in pool

| Turn off pool filter system
Release cable
Robot does not climb wall| Filter basket need to clean| Clean the filter basket
Rollers are worn or consumed too much| Replace new roller

ASN-AS-2021-Robotic-Pool-Cleaner- 11 ASN-AS-2021
-Robotic-Pool-Cleaner- 12 ASN-AS-2021-Robotic-Pool-Cleaner-
13

caution
“Working environment and application requirements

  1. Pool temperature : 10 C-35 C(50 F~95’F)
  2. Max. pool depth: 3m
  3. Pool type & materials: suitable for all pool types & materials
  4. Do not use the cleaner immediately after spraying the pool chemicals and do not use the cleaner as a dosing machine, which will damage and corrode the belts.
  5. Do not power on the cleaner when it is out of water.
  6. Do not operate the cleaner when there are people in the pool.
  7. The adapter or power supply should be connected to a leakage-protected and earthed socket.
  8. Fix the power supply at least 3.5m away from the pool edge and connect it with a fixed holder by the safety rope.
  9. The power connector must be pluggde in tightly.
  10. Avoid the collision and drop of the power supply and cleaner.
  11. Do not cover the power supply during working.
  12. Always clean and wash the filter tray after use.
  13. Take the cleaner out of the swimming pool after use. If the cleaner is immersed in the water for a long time, there will be microorganisms produced.
  14. The cable should be untwisted and wrapped properly after use.
  15. The cleaner should be placed in a shaded area, away from sunshine and heat during use, charging (for battery model) or storage.
  16. Use the original adapter only for Control box kit

Warranty

  1. This product is covered by Ausono warranty for 24 months ( only for driving kit and control box kit) from the date of purchase. Consumable parts are beyond of warranty which includes : Belt/ Filter basket/ Roller / Side cover
  2. This warranty is void if the product has been altered, misused, or has been repaired by unauthorized personnel

The following are excluded from Ausono warranty cover

  1. Device purchased as 2nd hand, used, or from unauthored
  2. Damage resulted from misused and abusive action.
  3. Damage resulted from chemical, fire, radioactive substance, poison, or liquid.
  4. Damage resulted from natural disaster.
  5. Damage caused to any 3rd party, person, object, and be we can only provide after sale services for products that are sold by Ausono, if you have purchased your unit from a different place, please for return and warranty issues.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals