VALBERG Plancha 984179 PLGAZ VAL-3B5934 Instruction Manual

VALBERG Plancha 984179 PLGAZ VAL-3B5934

Specifications

• Model: 984179 – PLGAZ VAL-3B5934
• Number of burners: 3
• Dimensions (W x D x H): 64 x 42 x 19 cm
• Cooking area (W x D): 59 x 34 cm
• Ignition: Manual (with Propane)
• Rated power (Qn): 0.70
• Injectors markings: PIN: 2575DO38762, 2575-23
• Others: Cat. I3+ ( ) 28-30/37, I3B/P (30)
• Gas Type: G30 – Butane: 28-30 mbar, G31 – Propane: 37 mbar, G30 – Butane /G30 – Propane: 30mbar

Product Usage Instructions

Before First Use
Assembly:

• Make sure all parts are in place according to the assembly manual.
• Use
  Connection to the Gas Cylinder:
  Connect the gas cylinder to the regulator following the correct pressure requirements.

Replacing the Gas Cylinder
Before changing the gas cylinder, ensure its valve is closed.

Leak Test
If a leak is detected, tighten the nuts and retest. Do not use the appliance until the leak is fixed. Do not use a flame to check for gas leaks.

Lighting the Appliance
Lighting of Main Burners:

• For models with a hood, light the barbecue with the hood open.
• Do not light with the hood down.
• For other models, remove the lid before lighting and place it behind the appliance to form a windbreak or on the floor.

FAQ

• Q: Can this product be used with both Butane and Propane gas?
  A: Yes, this product can be used with both G30 Butane and G31 Propane gas types.

• Q: How should I clean this product?
  A: The cooking plate, control knobs, and drip tray can be cleaned with warm soapy water and a soft cloth. Ensure the product is completely cooled before cleaning.

Thank you!
Thank you for choosing this VALBERG product. VALBERG products are chosen, tested, and recommended by ELECTRO DEPOT, so you can be sure you are getting a top-quality, easy-to-use product that won’t let you down.
We’re confident your new device will be a pleasure to use every day!
Welcome to ELECTRO DEPOT.

Product overview

Please read the regulatory instructions before using the product.

Parts

• A Control knobs x 3
• B Feet x 4
• C D rip tray
• D Cooking plate
• E Gas connector

Product overview

• Unpack and remove all labels from the unit. Please check that all product parts are included and undamaged. If the unit is damaged or faulty, do not use it and take it to your retailer or after-sales service centre.
• Keep all packaging out of the reach of children. There is a risk of accidents if children play with packaging materials.

Intended use

• This unit has been designed exclusively to cook food. It is designed to be used with butter, bacon, margarine, etc.Do not use it for any other purpose.
•  Any other use may damage the unit or cause injury.

Technical specifications

WARNING: This product was designed for use in the countries listed below:

France, United Kingdom, Spain, Italy, Portugal, Belgium, Luxembourg, Switzerland| I3+ (28-30/37)|

• G30 – Butane : 28-30 mbar G31 –
• Propane : 37 mbar

Netherlands| I3B/P (30)| G30 – Butane /G30 -Propane : 30mbar

Marking on injector, for example, 0.86 indicates that the size of the injector is 0.86mm.

Product usage

Before first use

• Run the unit for 5 minutes to remove all production residues. This will eliminate any residue created during the manufacturing process.
• The residue created during the manufacturing process may result in the unit emitting a faint burning smell when first turned on. This is completely normal and does not indicate a manufacturing defect or risk.
• Clean the unit and accessories (see Cleaning and maintenance).

Assembly

Product usage

Use

NOTE : Do not use this barbecue unless all parts are in place. The device must be correctly installed according to the assembly manual enclosed leaflet.
Connection to the gas cylinder
Cylinder/regulator

• The gas cylinder (NF compliant for France) can be put on the floor (next to the appliance) or on the bottom shelf/inside the trolley of your appliance (unless otherwise stated on the appliance). Indeed, it is necessary to keep a certain distance between the gas bottle and the burners during use. This is why some low shelves feature a location to put the gas cylinder by keeping a safe distance from the burners. The standard tablets are not suitable because the gas bottle is too close to the heating zone.
• The gas cylinder can be put on the bottom shelf/inside the trolley unless otherwise stated on the appliance and if its dimensions (included regulator) are according to the following drawing:
• If your gas cylinder doesn’t respect the required dimensions, put it on the floor, next to your appliance.
• Use only LPG cylinder.
• Do not obstruct the ventilation openings of the housing of the gas cylinder.
• Do not use a damaged or rusted gas cylinder. In case of damaged, please contact your gas cylinder supplier to make it checked. Do not use a gas cylinder with a damaged valve.
• Use a regulator with safety valve, in compliance with current national regulations (NF for France, BSEN 16129:2013 for other countries) of 37 mbar for Propane or 28-30 mbar for Butane.
• Note : For other countries, cylinder and regulator are dependant on the National Situations in countries of destination.
• NEVER USE YOUR PRODUCT WITH CITY GAZ. The gas circuit is produced only for Butane/Propane (G30/G31).
• NEVER USE TOOL TO TIGHTEN THE PRESSURE REGULATOR NUT ON YOUR PRODUCT: it can damage the product. A hand tight is sufficient.

Coupling head

• France: Use the G1/2 threaded gas inlet coupling head on the side or rear of your barbecue.
• Other countries: Use the ringed nozzle supplied as a spare part. Using an appropriate tightening tool (spanner), screw the ringed nozzle firmly onto the G1/2 threaded gas inlet G1/2 coupling head and then make a leakage test (see Leak test).

Supply hose
For all countries:

Note:

• Replace the main supply hose before its use-by date, if it is damaged, showing signs of cracks, or when required to do so by national regulations. It must be compliant with EN16436-1+A3:2020.
• Do not pull on the hose or kink it.
• Take care that the hose is not twisted or under any strain: the gas inlet coupling head being located on the left side, position the gas cylinder to the left of the appliance.
• Keep the hose away from parts of the appliance liable to become hot.
• Place the gas cylinder at least 1 metre away from the barbecue.
• A supply hose of a length of 1.2m or 1.5m (maximum) must be used for connection to the appliance.

France :

1. Use a hose with NF marking and a G1/2 threaded nut to screw onto the appliance, and an M20×1.5 threaded nut onto the regulator, in compliance with Norm XP D 36-125 or Norm XP D 36-112.
2. Screw the G1/2 threaded nut of the hose onto the inlet connection of the appliance and the M20×1.5 threaded nut (in black colour) onto the outlet connection of the regulator, following the instructions supplied with the flexible hose.
3. Check the gas-tightness of the entire system by making the leakage test (see Leak test).
   To regulator (black threaded head)
   To barbecue

Other countries :

1.  Use a flexible hose of a quality suitable for the use of Butane or Propane, in compliance with current national regulations. Connect the hose onto the ringed nozzle already installed on the appliance (see Connection to the gas cylinder), following the instructions supplied with the flexible hose.
2. Check the gas-tightness of the entire system by making the leakage test (see Leak test).

Replacing the gas cylinder
The gas cylinder must be changed in accordance with the following instructions:

• Do not change the cylinder when the appliance is in use (control knobs must be in OFF position (•))
• Wait until the appliance is completely cold
• Carry out replacement well away from any ignition source or heat source
• Replacement must only be carried out outdoors
• Before changing the gas cylinder, ensure that its valve is completely closed.

Leak test
It is imperative that you perform a “gas-tightness test”:

• Before using the barbecue for the first time (even if your barbecue has been assembled before purchasing)
• Every time the gas cylinder, hose or regulator is replaced.
• At least once a year, preferably at the beginning of the barbecue season.
• After the appliance has been left stored or unused for a long period of time.

Check that the hose is undamaged and is clear of the lower part of the barbecue.

• Perform leak tests outdoors only and keep away from any combustible materials. Do not smoke.
• Make sure all the control knobs are in «OFF» position (•).
• Make up a soapy solution of 50% washing up liquid and 50% water.
• Screw the regulator onto the gas cylinder.
• Connect the flexible supply hose to the appliance and to the regulator following the instruction (see Connection to the gas cylinder).
• With a paintbrush, apply the mixture to the gas cylinder/regulator/hose/coupling connections to the barbecue.
•  Turn on the gas cylinder valve.
• Observe the different gas cylinder/regulator/hose/coupling connections to the barbecue: if bubbles form, this indicates there is a gas leak.
• Turn off the gas cylinder valve.
• To correct the leak, tighten the nuts and perform the test again.
• If a part is faulty, get it replaced. The appliance must not be used until the leak is corrected. Should the problem continue, contact your dealer or a gas appliance technician.
• Important: Never use a flame to check for a gas leak.

Lighting the appliance

IMPORTANT before operation
Do not operate the appliance before you have carefully read and understood all the instructions. In addition, make sure that:

• the entire unit [cylinder/regulator/hose/appliance] is not leaking
• there is no blockage in the burners (venturi tube) and/or injectors (e.g. spiders’ webs)
• the supply hose is not damaged or past its use-by date, and is not touching any of the parts of the appliance that may become hot or sharp
• that the burners are connected correctly to the injectors by the orifice intended for this purpose.

Lighting of main burners

• IMPORTANT : for barbecue models with hood, light the barbecue with the HOOD OPEN. Never light the appliance with the hood down.
• For other models, remove the barbecue lid before lighting, and place it behind the main body of the appliance on the notch supplied for this purpose, in order to form a windbreak during cooking or put it on the floor. Never light the appliance with the lid down.

Automatic lighting:

1.  Remove the lid (open the hood) and make sure that all the knobs are in the “OFF” position (•) (push the knob and turn it in the direction of clockwise to the stop)
2. Turn on the gas cylinder valve →
3. Push on the left knob and rotate to the “CLICK” in order to ignite the 1st burner.
4. In the same way, continue to light the other burners proceeding from left to right.
5. If one or more burners fail to ignite after steps 2 and 3, turn the knob to the “OFF” position and repeat the operation 2 or 3 times.
6. If one or more burners still fail to ignite, shut off the gas supply, wait 5 minutes for the gas to clear and repeat steps 2 and 3 or light the burners with a commercial lighter (see  Lighting of side burner).

Manual lighting:

• Should automatic lighting fail to work, place all the control knobs on “OFF” (•). Place a lit match or a commercial lighter close to the burner ports, and then turn the control knob to the high position (represented by a large flame symbol).
• Should one or more burners fail to light after several attempts at automatic and/or manual lighting, check that the burners and/or injectors are not blocked.

Lighting of side burner

• IMPORTANT : make sure to open the side burner hood before lighting it. Never let the side burner hood closed during lighting or using of side burner. The side burner is designed for pan with a diameter from 10 to 22cm. Make sure to respect these dimensions.

Automatic lighting:

1. Open and make sure that the knob is in the “OFF” position (•) (push the knob and turn it in the direction of clockwise to the stop)
2. Turn on the gas cylinder valve
3. Push on the knob and rotate to the “CLICK” in order to ignite the burner.
4. If the burner fail to ignite after steps 2 and 3, turn the knob to the “OFF” position and repeat the operation 2 or 3 times.
5. If the burner still fail to ignite, shut off the gas supply, wait 5 minutes for the gas to clear and repeat steps 2 and 3 or light the burner with a commercial lighter (see §D2). Do not put anything on the hood of side burner. Only put stuff on the right side shelf.

Manual lighting:

• Should automatic lighting fail to work, place control knob on “OFF” (•). Place a lit match or a commercial lighter close to the burner port, and then turn the control knob to the high position (represented by a large flame symbol).
• Should one or more burners fail to light after several attempts at automatic and/or manual lighting, check that the burner and/or injector are not blocked.

Extinguishing the appliance

1.  Return all the knobs to the “OFF” position (•) (push the knob and turn it in the direction of clockwise to the stop)
2. Turn off the gas cylinder valve.
3. Wait until the appliance is completely cold before replacing the lid (depending on model).

Preheating/ Commissioning the appliance

• IMPORTANT : It is imperative that you perform the leak test before using the appliance for the first time (see Leak test).
• Before using the appliance for the first time, we recommend that you heat your appliance «blind» (i.e. without food) for 30 minutes on the highest setting with all the accessories.
• This may cause some odour and/or smoke emissions due to the carbonisation of material residues. Wait until the appliance is completely cold, clean with water and a soft cloth, and then lightly oil the cooking surfaces.

Cooking

• For barbecues equipped with a plancha: lightly oil the cooking surface to prevent food sticking. For barbecues with hood: there are 2 possible cooking modes:
  • Traditional grilling with the hood open.
  • Oven-type grilling with the hood closed: ideal for large cuts of meat.
  • WARNING! For traditional grilling like grilled sausages …, do not close the cover. This type of food gives off a lot of fat and oven-type grilling is not suitable.
  • Tip: To facilitate cleaning of the grease drawer, we advise you to line its surface with a sheet of aluminum foil, to be thrown away after each use once the appliance is completely cold.
  • If fat get burn, turn down the intensity of the heat to low and move the food to a cooler area. NEVER USE WATER TO TURN OFF THE FLAMES IN A GAS BARBECUE.

Cleaning and maintenance

Cleaning and storage

• Wait until the barbecue is completely cold.
• For hygiene and safety reasons: carefully clean your appliance and all its accessories (including the grease drawer) after each use, using hot soapy water and a soft non-abrasive cloth, in order to remove grease residue and using a soft non-abrasive cloth. Dry and oil cast iron surfaces.

WARNING! For barbecues equipped with a front panel, it may be necessary to remove it in order to take the grease drawer for cleaning.

To clean the plancha:

• never use scouring or abrasive objects or detergents. To remove cooked-on grease and meat juices efficiently, deglaze it just after cooking (the cooking plancha must be hot):
•  Switch off the appliance, wear suitable protective gloves against the heat of the plancha, and throw a small quantity of water on the surface to be cleaned. Be careful of the heat produced by the steam. Remove any residue with a spatula in the slit in the plancha. Finish cleaning with a soft sponge. Dry and lightly oil. You can replace the water by vinegar on a warm cooking plancha.

To clean the side shelves:

• clean these parts after each use, using hot soapy water and a soft non-abrasive cloth. Rinse and dry.
• The side shelves do not be use as cutting board.
• Do not clean the grills/planchas or accessories in a self-cleaning oven: you risk damaging them.
• Protect the appliance (after disconnecting from the gas cylinder) with a cover during warm weather and then store it in a cool and dry place.
• Turn off the gas cylinder valve after each use.
• Disconnect the gas cylinder when the appliance is not in frequent use. Check that the gas cylinder valve has been properly turned off.
• Store the gas cylinder in a dry, well-ventilated location, out of the reach of children and away from any combustible source. Do not store the gas cylinder in a cellar or basement.
• WARNING! Propane should only be stored outdoors, in a cool, dark place.
• Butane and Propane gas cylinders must not be place near or under the radiation of a heat source. Disconnected gas cylinders must be kept turned off, even when presumed empty, in a ventilated area.
• WARNING! Element in stainless steel (cooking grids, burners,…) will be colored in normal use. This is normal for this kind of material.

Maintenance
To maximise the life of your barbecue, we recommend that you:

• Clean all cooking surfaces after each use.
• Do not leave your barbecue out in the rain; do not allow water to stagnate on the cooking surfaces, the trays of the grease drawer: risk of deterioration and/or premature corrosion.
• Oil cast iron cooking surfaces to prevent rust.
• Frequent cleaning of the burner allows it to remain in good condition for numerous times of use and prevents premature oxidation (acid residues from grilled food).
• Oxidation of the burner is nevertheless a normal occurrence over time and an oxidised burner that works does not need replacing.
• Replacement is only necessary if it is not working properly despite the instructions of this manual having been followed.

WARNING! After a long storage period, check that the burners (venturi tubes) are not blocked by insects: risk of fire or flame flashback. If necessary, clean the inside of the burners (venturi tubes) with a pipe cleaner.
Damage caused by fat fires is not covered by the warranty.

Troubleshooting

IMPORTANT:

• NEVER DISMANTLE THE GAS RAMP
• FITTED INTO THE BARBECUE (located behind the front control panel)
• NOR THE VALVES OR INJECTORS

• Take off the burner that is not working and replace it for test purposes by one of the other (working) burners that you have also dismantled. Test to see if it will have good color of flame:
• If the «replacement» burner   (used for the test) does not light. This means that the injector is blocked. Clean it with compressed air (generally available from your dealer).
• If the « replacement » burner (used   for the test) lights. This means that the initial burner is blocked. Clean it with compressed air (generally available from your dealer).

Flames are coming out of one of the knobs on the front control panel| • Immediately close the gas valve. Do not perform any replacement tests on the knob in question, but take off the burner and clean both it and the injector with compressed air (generally available from your dealer).
Problem encountered| Possible causes| Proposed solutions
---|---|---

• I am unable to light my barbecue when using it for the 1st time or after having used it several times
• When using my barbecue for the first time or after having used it several times, none of the burners will light

| Refer to case n°2: Do not perform the replacement tests, but take off all the burners and clean both these and the injectors with compressed air (generally available from your dealer).

• Gas cylinder valve closed, not
• sufficiently open or not drained
• Gas cylinder empty
• Cylinder-barbecue connection hose blocked

|

• Open (or open further) the gas cylinder valve in order to release gas in the barbecue circuit. If it doesn’t work, you must drain your hose by pushing the knob situated on the hose at the level of the gas cylinder.
• Try lighting the barbecue using a new gas cylinder. If the barbecue lights   with the new cylinder , this means that your initial cylinder was empty.
• Try lighting the barbecue with another connection hose. If the   barbecue lights with the new   cylinder , this means that your initial cylinder was empty. Clean it with compressed air (generally available from your dealer).

The barbecue burners will not light with the (piezzo) ignition button but will light with a match| Faulty (piezzo) integrated electronic ignition system or misplaced| Gently move the tip of Piezzo so that it is located about 3-4mm of the burner and at a hole of the burner. If that does not work, it means that the Piezzo is defective. Contact your dealer.
Problem encountered| Possible causes| Proposed solutions
---|---|---
The flame of my barbecue is yellow instead of blue| Burner (venture tube) is blocked or injector not well placed|

• Take off the burner that have a yellow flame and replace it for test purposes by one of the other (working) burners that you have also dismantled. Test to see if it will have good color of flame:
• If the «replacement» burner (used   for the test) have yellow flames. This means that the injector is not well placed. Thus, there is too much air in the air/gas ratio which causes the
• appearance of yellow flames. Contact your dealer.
• If the « replacement » burner (used   for the test) does not have yellow   flames. This means that the initial burner is blocked. Clean it with compressed air (generally available from your dealer).

The barbecue has set on fire, there are flames coming from the barbecue|

• Grease build-up and insufficient cleaning and care of barbecue
• Food grease has fallen onto the burners during cooking

|

• Clean the barbecue
• Always use the barbecue with the flame protectors correctly positioned over the burners

I am unable to connect my barbecue to the regulator of the gas cylinder (France ONLY)|

• The peripheral hose is not suitable for the G1/2 standard screw connector on our barbecues.
•  The peripheral hose is suitable for the G1/2 standard screw connector on our barbecues, but is not being connected the right way round.

|

• Purchase a hose compliant with Norm NF D 36125 or Norm XP D 36112 (threaded nuts G1/2 and M20×1.5 respectively).
• Check which way round the hose must be connected. Attention the 2 nozzles on the hose are different: one (black-coloured) is for connection to the regulator, the other for connection to the G1/2 threaded gas inlet head of the barbecue.

been connected the right way round, and the black nozzle of the hose intended to be connected to the regulator has been forced on to the G1/2 gas inlet threaded coupling head of the barbecue|  Barbecue cannot be used, contact your dealer
Your connection is an American fitting|  Impossible|  All our gas barbecues are equipped with fittings compliant (respectively) with the different national regulations
I am unable to connect my barbecue to the regulator of the gas cylinder (Other countries)| The peripheral hose is not suitable for the universal coupling head supplied with our barbecues|  Purchase a flexible tube/hose suitable for the coupling nut supplied and compliant with current national regulations
My stainless steel burners have changed colour the 1st time I used the barbecue| This is absolutely normal as stainless steel is a material which reacts to being heated by a change in colour
My new barbecue seems to have already been used| Your barbecue has been part of a batch of samples tested under laboratory conditions, which could explain signs of use
My plancha is eroded| •  Contact your dealer|
Problem encountered| Possible causes| Proposed solutions
---|---|---
My plancha cracked the 1st time it was heated|  Manufacturing fault linked to the manufacturing process of cast iron parts: an air bubble may accidentally be present when the molten iron is placed in the mould| Contact your dealer

Storage

WARNING!

• Butane and Propane gas cylinders should only be stored outdoors, in a cool, dry place, and away from direct sunlight.
• Gas cylinder must not be place near or under the radiation of a heat source. Disconnected gas cylinders must be kept turned off, even when presumed empty, in a ventilated area.
•  Before storing the unit, ensure that it has cooled, cleaned and dried thoroughly.
• Turn off the gas cylinder valve after each use. Disconnect the gas cylinder from the unit when the unit will not be use for a long time.
•  Store the gas cylinder in a dry, well-ventilated location, out of the reach of children and away from any combustible source. Do not store the gas cylinder in a cellar or basement.
• Protect the unit (after disconnecting from the gas cylinder) with a cover during warm weather.
• Store the appliance in a cool, dry place.

WARRANTY CONDITIONS

This product is guaranteed against faults caused by defects in manufacturing or the materials used for a period of two years, starting from the date of purchase. This warranty does not cover defects or damage caused by failure to install the device correctly, incorrect use of the product, or excessive wear and tear.
proof of purchase required

ELECTRO DEPOT

Documents / Resources

| VALBERG Plancha 984179 PLGAZ VAL- 3B5934 [pdf] Instruction Manual
984179, VAL-3B5934, Plancha 984179 PLGAZ VAL-3B5934, Plancha 984179, Plancha PLGAZ VAL-3B5934, PLGAZ VAL-3B5934, Plancha, Plancha VAL-3B5934, PLGAZ VAL- 3B5934, VAL-3B5934, PLGAZ
---|---

References

• Alt innen reklame i over 25 år
• valberg.de is available for purchase - Sedo.com
• Electro Depot - Somos victimas de nuestro éxito.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>