HAVIS UT-1000 Series Universal Cradles Owner’s Manual

HAVIS UT-1000 Series Universal Cradles

Related Products

Havis offers a wide variety of accessory products for use with the UT-1000 & UT-2000 Series Universal Cradles.
For more information or to order, please visit www.havis.com.

LPS-211
Power Supply Mounting Bracket
Mount a power supply directly to your Universal Cradle with this versatile bracket.

DS-DA-421
Screen Support
Secure your laptop screen to prevent excess wear and reduce vibration while in use.
For use with UT-1000 Universal Cradles only.

DS-DA-218
Desktop Stand
Durable stand for mounting Havis Universal Cradles in the home or office.

Universal Cradle
Related Products
Please visit www.havis.com for a full list of all Derivative Products and Replacement Part Kits.

DS-DA-503
Replacement Keys
Set of two (2) replacement keys for the Havis Universal Cradle.

Before Beginning

Havis is pleased to provide this Owner’s Manual to aid in the proper installation and use of the Universal Cradles.
For questions regarding the set-up of your Universal cradle, please contact Havis at 1-800-524-9900 or visit www.havis.com for additional product support and information.

This Owner’s Manual applies to the following Part Numbers:
UT-1000 Series
UT-2000 Series

• NEVER STOW OR MOUNT THE HAVIS UNIVERSAL CRADLE DIRECTLY IN A VEHICLE AIRBAG DEPLOYMENT ZONE.

• DO NOT USE COMPUTER WHILE DRIVING
  

• READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION.

Specifications

UT-1001 Dimensions (Base Model Universal Cradle)

Overall Dimensions| 13.47” ( 34.21 cm) W x 11.30” ( 28.70 cm ) D x 2.14” ( 5.43 cm ) H
Weight| 3.72 lbs ( 1.69 kg )
Compatible Computer Dimensions
Width| 11.43” (29.0 cm) to 14.23” (36.1 cm)
Depth| 9.27” (23.5 cm) to 11.02” (27.9 cm)
Height| 0.66” (1.7 cm) to 1.86” (4.7 cm)
UT-2001 Dimensions (Base Model Universal Cradle)
Overall Dimensions| 10.41” ( 26.44 cm) W x 8.39” ( 21.31 cm ) D x 2.31” ( 5.87 cm ) H
Weight| 2.38 lbs ( 1.08 kg )
Compatible Computer Dimensions
Width| 9.30” (23.6 cm) to 11.24” (28.5 cm)
Depth| 6.83” (17.3 cm) to 8.13” (20.79 cm)
Height| 0.55” (1.4 cm) to 0.93” (2.4 cm)

For information about the specifications of your model Universal Cradle, please visit www.havis.com or contact Technical Support at 1-800-524-9900

Parts Included

Universal Cradle

(UT-1000 Series shown, UT-2000 Series similar)

Top View

A| Latch Release Handle/Lock
B| Front Fences (x2)
C| Rear Fence(s)
UT-1000 (x2), UT-2000 (x1)
D| Side Hold-down Lugs (x4)
E| Side Trays (x2)
F| Rear Tray

Bottom View

G| Rear Tray Adjustment Screws (x2)
H| Side Tray Adjustment Screws (x2)
I| Mounting Holes (VESA 75mm, 4x M4)
J| Strain Relief Holes (x4)
K| Front Fence Adjustment Screws (x2) UT-1000 Only
L| Rear Fence Adjustment Screw(s)
UT-1000 (x2), UT-2000 (x1)
M| Side Hold-down Lug Adjustment Screws (x4)

Hardware Kit

This Hardware Kit includes:

1. Zip Ties (2)
2. Integrated Zip Ties (4)
3. Pan Head Screws, M4 x 0.7 x 12mm long (5)
4. Washers, M4 (5)
5. Lock Washers (5)
6. L-shaped Wrench (1)
7. Keys (2)
   

Configuration

THE INFORMATION IN THIS MANUAL APPLIES TO ALL HAVIS UNIVERSAL CRADLE PRODUCTS.
IF YOU HAVE A DERIVATIVE PRODUCT, FIRST FOLLOW THE INSTRUCTIONS INCLUDED WITH YOUR SPECIFIC KIT, THEN PROCEED WITH THE CONFIGURATION, INSTALLATION, AND OPERATION INSTRUCTIONS IN THIS MANUAL.

1. Ensure the Universal Cradle is latched by pushing inward on both Side Trays.
   Trays should be up against top surface as shown.
   

2. Turn the Universal Cradle over and loosen both Side Tray Adjustment Screws and fully extend both Side Trays.
   

3. Retighten both Side Tray Adjustment Screws and unlatch the Side Trays by pulling out the Release Handle. The Side Trays are spring-loaded and should extend fully.
   

4. Loosen both Rear Tray Adjustment Screws and fully extend the Rear Tray.
   (DO NOT REMOVE SCREWS)
   

5. Before fitting your tablet or laptop on the Universal Cradle, make sure you turn the computer’s power off and remove any connected cords or peripherals.

6. If mounting a laptop, place in the center of Universal Cradle and open the screen.
   If mounting a tablet, choose the best orientation to prevent Front Fences and Side Hold-down Lugs from blocking access to crucial ports or controls.
   Next, ensure your computer is in contact with both Front Fences and centered on the tray. Latch both Side Trays by pushing in until a click is heard and the Side Trays maintain their latched position.
   

7. While holding computer in position, carefully flip the Universal Cradle over and adjust the Rear Tray inward until the Rear Fence(s) contacts the computer.
   Ensure contact is maintained with Front Fences. Retighten Rear Tray Adjustment Screws. Torque screws to 22 in-lbs (0.25 Nm) ± 10%.
   

8. Loosen Side Tray Adjustment Screws and push in the Side Trays equally until contacting both sides of computer. Retighten Side Tray Adjustment Screws.
   Torque screws to 22 in-lbs (0.25 Nm) ± 10%.
   

9. Carefully flip the Universal Cradle & computer over and adjust the four (4) Side Hold-Down Lugs vertically until firm contact is achieved with computer.
   NOTE : To verify proper set-up, pull Latch Handle to ensure Side Trays release fully. If they do not, too much downward pressure was exerted during adjustment. Loosen and re-adjust as needed.
   

10. If required to prevent blocking a crucial port or control, the Front, Side, and/or Rear Fences can be adjusted along the length of the computer.
    Loosen Fence Adjustment Screw and slide Fence laterally. For UT-2000 Series Universal Cradles, ONLY the Rear Fence can be adjusted. To move the Rear Fence to one of the other slots, remove the Rear Fence Adjustment Screw and move the Rear Fence to one of the outer slots. Retighten Fence Adjustment Screw(s). Torque screws to 22 in-lbs (0.25 Nm) ± 10%.
    

11. If you change computer model or add a protective cover for your tablet, you will need to reconfigure your Universal Cradle by following the Configuration instructions starting on Page 4 of this Owner’s Manual.

Installation

The Universal Cradles use a VESA 75mm hole pattern for mounting.
For additional technical support with mounting the Univeral Cradle in your specific work environment, please contact Havis at 1-800-524-9900.

1. Align the four holes on the mounting surface with the four Mounting Holes on the bottom of the Universal Cradle. Secure Universal Cradle to the mounting surface using four Pan Head Screws (Hardware Kit Item #3) . Torque screws to 36 in-lbs (0.4 Nm) ± 10%.
   
   

Cable Management

1. If it is necessary to strain relieve wires/cables, insert Integrated Zip Ties (Hardware Kit Item #2) into any of the Strain Relief Holes on the bottom of the Universal Cradle. Loop and tighten Zip Tie around wires/cables as required and trim excess Zip Tie as needed.
   

2. Additional Strain Relief Holes have been provided on each of the four corners of the Universal Cradle. If necessary, use these holes along with the provided Zip Ties (Hardware Kit Item #1) to strain relieve wires/cables.
   Loop and tighten Zip Tie around wires/cables as required and trim excess Zip Tie as needed.
   

Operation

1. Before placing your computer into your Universal Cradle, and before taking your computer out of your Universal Cradle, unlatch by pulling out the Latch Handle, extending each of the two Side Trays. The Rear Tray should remain fixed.
   

2. Place computer in center of unlatched Universal Cradle, ensuring the device is touching both Front Fences as well as the Rear Fence, then push inward on both Side Trays until a click is heard.
   

3. For theft deterrence, secure computer by locking the Universal Cradle with the supplied Key (Hardware Kit Item #6).
   

Customer Support

Havis, Inc.
75 Jacksonville Road
Warminster, PA 18974
www.havis.com 1-800-524-9900

References

• Rugged Vehicle Mounts, Consoles, Docking Solutions | Havis Inc. NRL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>