VALBERG 973766 Heater User Manual

: June 1, 2024
: VALBERG

Table of Contents

VALBERG 973766 Heater
Product Usage
Product overview
Specifications
Product usage
Operation
Cleaning and maintenance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VALBERG 973766 Heater

VALBERG-973766-Heater-product-image

Specifications

Model: Radiateur Heater
Operating voltage: 220-240V~,50Hz
Power: 2.0 kW
Current: 10 A (maximum continuous draw)
Dimensions (W x D x H): 530 x 170 x 380 mm
Weight: 2.70 kg
Protection class: Class I
Protection class (IP): IP20

Product Usage

Assembly
Before using the product, assemble the following components:

Air outlet
Feet (x2)
Air inlet (on the bottom)
Screw (x2)

Operation
Follow these steps to operate the Radiateur Heater:

Plug in the device to a power source with the specified voltage.
Turn on the heater using the designated switch or control.
Adjust the heat output as needed based on the desired temperature.
Monitor the device while in operation to ensure safe and efficient heating.

Cleaning and Maintenance
To keep your Radiateur Heater in good condition, follow these cleaning and maintenance tips:

Regularly clean the air outlet and air inlet to prevent blockages.
Avoid using abrasive cleaners that may damage the surface of the heater.
Check for any loose screws or parts and tighten them if necessary.
Store the heater in a dry and dust-free environment when not in use.

Frequently Asked Questions (FAQ)

Q: What should I do if the heater is not heating properly?
A: Check if the power source is functioning correctly and ensure that the heater is plugged in securely. If the issue persists, contact customer support for assistance.
Q: Can I leave the heater unattended while it is operating?
A: It is not recommended to leave the heater unattended while it is in operation for safety reasons. Always monitor the device when it is turned on.
Q: How can I adjust the heat output of the Radiateur Heater?
A: Most heaters have adjustable settings either on the device itself or through a remote control. Refer to the user manual for specific instructions on adjusting the heat output.

Thank you!
Thank you for choosing this VALBERG product. VALBERG products are chosen, tested, and recommended by ELECTRO DEPOT, so you can be sure you are getting a top-quality, easy-to-use product that won’t let you down.
We’re confident your new device will be a pleasure to use every day!
Welcome to ELECTRO DEPOT.

Product overview

Parts

$VALBERG-973766-Heater-$3$$

A Air outlet
B Handle
C Power dial
- O – Off
- I – Low power (800 W)
- II – Medium power (1200 W)
- III – High power (2 000 W)
D Temperature dial – MIN / MAX (low to high power)
E Feet (x2)
F Air inlet (on the bottom)
G Screw (x2)
Unpack and remove all labels from the unit. Please check that all the product’s parts are included and intact. If the unit is damaged or faulty, do not use it and take it to your retailer or after-sales service centre.
Keep all packaging out of the reach of children. There is a risk of accidents if children play with packaging materials.

Intended use

This product is for domestic use only. It has not been designed for industrial or professional use.
Any other use may damage the product or cause injury.

Specifications

Model: 973766 – VAL-CH20
Operating voltage: 220-240V~,50Hz
Power:
Low – 800 W
Medium – 1200 W
High – 2000 W
Current: 10 A (maximum continuous draw)
Dimensions (W x D x H): 530 x 170 x 380 mm
Weight: 2.70 kg
Protection class: Class I
Protection class (IP): IP20

This product complies with the requirements imposed by directives 2014/35 / EC (repealing the Directive 73/23 / EEC as amended by Directive 93/68 / EEC) and 2014/30 / EC (repealing the Directive 89/336 / EEC).

Information requirements for electric local space heaters| | | P
---|---|---|---
Model identifier(s): VAL-CH20| | |
Item| Symbol| Value| Unit
Heat output| | |
Nominal heat output| Pnom| 2.0| kW
Minimum heat output (indicative)| Pmin| 0.8| kW
Maximum continuous heat output| Pmax, c| 2.0| kW
Auxiliary electricity consumption| | |
At nominal heat output| elmax| N/A| kW
At minimum heat output| elmin| N/A| kW
In standby mode| elSB| 0| W
Type of heat input, for electric storage local space heaters only (select one)
Manual thermal load control with a built-in thermostat| | | No
Manual thermal load control with room and/or outdoor temperature feedback| No
Electronic thermal load control with room and/or outdoor temperature feedback| | No

Fan-assisted heat output

Fan-assisted heat output	No

Type of heat output/room temperature control (select one)|
Single-stage heat output with no room temperature control| No
Two or more manual states with no room temperature control| No
Room temperature control with a mechanical thermostat| Yes
With an electronic room temperature control| No
Electronic room temperature control and a daily programmer| No
Electronic room temperature control and a weekly programmer| No
Other control options (multiple selections possible)|
Room temperature control with a presence detector| No
Room temperature control with an open-window sensor| No
With remote control option| No
With delayed start control| No
With a limited operating time| No
With a black globe sensor| No

Contact details:
ELECTRO DEPOT
1 route de Vendeville
59155 FACHES-THUMESNIL- FRANCE

Note:
For electric local space heaters, the measured seasonal space heating energy efficiency η = cannot be less than the declared nominal heat output value of the unit.

Product usage

Assembly

Turn the heater upside down and place it on a protected surface to avoid scratching it.
Remove the 2 screws from the underside of the heater.
Align the hole on the feet with the screw holes on the heater. The open edge of the feet should be facing outwards. Insert the screws and tighten them until they are securely fastened in place.
Turn the heater upright.

Before using the product
WARNING!

Correctly connect the unit and do not leave it within the reach of unsupervised children.
It is normal for heaters to emit an odour and smoke when they are turned on for the first time or have not been used for a certain period of time. This will disappear after a short while.
The heater must always be placed in an upright position on a horizontal surface. If the heater tips over, turn it upright immediately.
Place the heater on a stable, heat-resistant and non-combustible horizontal surface that is at least 30 cm (sides and rear) and 50 cm (front) clear of objects such as walls, furniture and curtains.
Never place the heater below electrical sockets.
The heater is suitable for use in a 10-15 m² space, such as a living room or office.
Do not use the heater in a bathroom or near to a swimming pool or other body of water. The heater must never become wet. Do not use the heater in wet or humid conditions.
Make sure the air inlets are unobstructed. Do not cover the heater’s air inlet or outlet vents/grilles.

Operation

Fully unwind the power cable.
Check the heater’s rating plate for the correct voltage. Make sure the temperature dial is in the MIN position and the power dial is set to the off position (0). Connect the plug to a mains socket with a suitable voltage.
Turn the temperature dial clockwise towards the MAX mark until you hear a clicking sound and the heater starts to work. Turn the temperature dial up to increase the temperature.
Turn the power dial to select the power level: I (low), II (medium) or III (high).
Turn the temperature dial anticlockwise towards the MIN mark to decrease the heater temperature.
To turn the heater off, turn the temperature dial anticlockwise as far as it can go (MIN position) and turn the power dial to the off position (0). Unplug the unit from the mains socket.

NOTE:

When turning the temperature dial up, the clicking sound indicates that the thermostat is starting to work and the desired function is activated. Similarly, when turning the temperature dial down, the click indicates that the thermostat has turned off and the function is deactivated.

Heater safety features

The heater has a built-in overheating protection mechanism. A safety switch will cut off the power if the heater overheats (e.g. the air inlets/outlets are totally or partially blocked). Turn the power dial to the off position (0) and the temperature dial to the (MIN) position. Unplug the plug from the mains socket. Wait 30 minutes for the heater to cool down.
Remove the source of overheating (e.g. a blockage in the vent holes/grilles or excessive dust or dirt on the unit).
Turn the heater back on.

NOTE: If overheating continues or the unit repeatedly malfunctions, return the heater to an approved service centre.

Cleaning and maintenance

WARNING!

Before cleaning, always turn off and unplug the heater and allow it to cool down sufficiently.
Do not use flammable or abrasive detergents such as benzene or white spirit to clean the heater.
Never immerse the heater, power cable or plug in water.
Clean the exterior with a damp, soft cloth. Thoroughly dry the heater before using it again.
If you do not plan on using the heater for a long period of time, we recommend removing the feet and storing it in its original packaging in a cool, dry place, away from direct sunlight, excessive dust and dirt.

Storage

Always unplug the unit from the mains before storing it. Wait until the heater has cooled down before storing it.
Store the unit in a fresh, dry and dust-free place, out of the reach of children and pets.
Please retain the packaging and use it to store your unit when it is not in use for an extended period of time.

WARRANTY CONDITIONS
This product is guaranteed against faults caused by defects in manufacturing or the materials used for a period of two years, starting from the date of purchase. This warranty does not cover defects or damage caused by failure to install the device correctly, incorrect use of the product, or excessive wear and tear. proof of purchase required.