Westinghouse W-804 LED Indoor/outdoor Lighting Fixture Owner’s Manual
- August 4, 2024
- Westinghouse
Table of Contents
W-804
032823
Owner’s Manual
LED Indoor/outdoor Lighting Fixture
Installation Instructions
WARRANTY INFORMATION
This luminaire is warranted to be free from defects in materials and workmanship for 5 years. If the product fails during the warranty period, return defective product to seller. Warranty terms and conditions of seller apply. If replacement product is not available through seller, please contact www.westinghouselighting.com/contact-us.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed to give you many years of beauty and service. For questions and comments, please visit www.westinghouselighting.com/contact- us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any packing materials.
NOTE: THIS FIXTURE IS SUITABLE FOR USE WITH DIMMABLE SWITCHES, SEE BELOW FOR LIST OF COMPATIBLE DIMMERS.
Brand
| Model #| DIMMING RANGE
---|---|---
Lutron| DVCL-153P, MACL-153M, PD-6WCL, MRF2-6CL, |
10-100%
SCL-153P, DVCL-253P-WH, S-600, LECL-153P
Leviton
|
DDMX1-BLZ, C22-6672-1LW, C26-RNL06-TW, DW1KD,
|
10-100%
DL1KD, R62-6683-IW, DL6HD, DW6HD, R62-6674-POW,
002-6674-10W, RDL06-10Z, IPL06-10Z, 012-TSL06-1LW,
RNL06-10Z, DSL06-1LZ
Cooper
| DAL06P-C1|
10-100%
Not recommended for use with motion sensors, light sensors, timers or any other external controls.
WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
- Read all instructions carefully before installation and operation.
- If you are not familiar with state and local electrical codes, it is recommended that you consult with a qualified electrician.
- Suitable for wet location. The driver housing is mounted inside the ceiling, which can not be reached by the the water, which should be installed by qualified electrician.
- Non-replaceable LEDs.
- Caution: LEDs emit bright light. Avoid looking directly into the light source for prolonged periods to avoid eye damage.
- Not to be used with electronically controlled switch.
INSTALLATION STEPS
1. Use the hole size template included in box to drill the hole in ceiling. Prepare supply wires: Install and unshield the line feed cable 6” (15cm) and strip wires 5/8” (1.6cm). (Fig.1)
Fig. 1
A: 52261: Ø4.25″±0.1″
B: 52271: Ø 6.30″ ±0.1″
2. Open the cover of the junction box. Push and remove one of the knockouts on the side panel of the junction box. Install the supply wire strain relief (not included). (Fig. 2)
Fig. 2
3. Bring supply power into junction box through the strain relief. Use the wirenuts to connect the white wire from the supply wire with the white wire of the junction box. With a wirenut, connect the black wire from the supply wire with the black wire of the junction box. With a wirenut, connect the copper wire from the supply wire and with the green wire of the junction box. (Fig. 2)
4. Put all wires and connections back into the junction box and close the cover securely. (Fig. 2)
5. Connect junction box to recessed LED panel with the quick lock connector. (Fig. 3)
Fig. 3
6. Move the slide switch to your appropriate light color (2700K /3000K /3500K /4000K /5000K). Place junction box into the ceiling through cut-out. (Fig. 3)
7. Pull the spring clips on the fixture up and through the cut-out. Spring clips should close above the ceiling and secure recessed LED panel in place. (Fig. 4)
Fig. 4
CLEANING AND CARE
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to clean this fixture.
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
and Westinghouse are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting.
All Rights Reserved. Made in Cambodia
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>