Hotpoint AH12E15D5B PTAC with Electric Heat Instructions

Hotpoint AH12E15D5B PTAC with Electric Heat

Product Information

Product Model: AH12E15D5B

Dimensions and Installation Information:

• Wall Case Dimensions:
  • A: 70 inches
  • C: 30 inches
• Maximum Cord Extension: 30 inches
• Wall Opening Dimensions: Add 1/4 to A and C dimensions for all cut-outs. RAB80 16-1/4 Min. H x 42-1/4 Min. W

AH12 Electric Heater Specifications:

• Voltage: 230/208 Volt
• Line Cord Connected Units
• Heater Watts: 5,000 / 4,100
• Heater BTU: 15,000 / 12,000
• Heater Amps: 22.3 / 20.1
• Minimum Circuit: 30 Amps
• Recommended Protective Device: 30 Amp Time-Delay Fuse or Breaker

Product Usage Instructions

To install the AH12E15D5B electric heater, follow these steps:

1. Measure the wall case dimensions A and C, which should be 70 inches and 30 inches respectively.
2. Ensure the wall opening dimensions are appropriate by adding 1/4 inch to A and C dimensions for all cut-outs. The minimum required dimensions are 16-1/4 inches in height and 42-1/4 inches in width.
3. Connect the unit to a 230/208 Volt power source using the line cord.
4. Take note of the heater specifications:
   • Heater Watts: 5,000 / 4,100
   • Heater BTU: 15,000 / 12,000
   • Heater Amps: 22.3 / 20.1
   • Minimum Circuit: 30 Amps
   • Recommended Protective Device: 30 Amp Time-Delay Fuse or Breaker
5. Ensure the electrical circuit can support the required amps and install a 30 Amp time-delay fuse or breaker as the recommended protective device.

Please refer to the user manual for additional information or troubleshooting tips.

DIMENSIONS AND INSTALLATION

INFORMATION (IN INCHES)

WALL CASE DIMENSIONS
RAB80 WALL SLEEVE Heavy-gauge galvanized steel, with insulation, for quick self-assembly. A – 42”, B – 13-3/4”, C – 16”

MAXIMUM CORD EXTENSION
WALL OPENING DIMENSIONS Add 1/4” to A and C dimensions for all cut-outs. RAB80 16-1/4” Min. H x 42-1/4” Min. W

ELECTRICAL WIRING

All wiring, including installation of receptacle, must be made in accordance with local electrical codes and regulations.
NOTE : Aluminum wiring may pose special problems – consult a qualified electrician.

GRILLE OPTIONS

• Stamped Aluminum Grille – RAG70

ELECTRICAL CONNECTION

• 230/208 volt units must be plugged into a receptacle. Installation must comply with local electrical codes and regulations.
• Power cord is permanently attached on all Hotpoint chassis

FEATURE AND BENEFITS

• 14,500 / 14,300 cooling BTU
• 10.3 / 10.4 EER
• R32 Refrigerant – Environmental friendly, low GWP (Global Warming Potential)
• 3-Speed Fan – Give guests control over their comfort with three fan speeds to choose from
• 4-Temperature Limiting Options – Easily select one of four temperature ranges for peak efficiency and total customer comfort
• Intuitive Display – Allow guests to easily customize their preferred settings and reduce maintenance calls with an easy-to-use control panel
• Power Cord (LCDI) Included – Hotpoint PTACs come with everything needed for a quick and easy installation
• Automatic Emergency Heat – Keep guests comfortable with a heating option that uses electric resistance heat in heat pump mode
• Freeze and Frost Protection – Automatic freeze and indoor frost control keep units operating in peak condition
• Auto Power Recovery – In case of power failures, units automatically resume their operation when power restores, reducing maintenance calls
• Self Diagnostics – Quickly and easily identify service needs with a nine-point diagnostic code system
• Backed by an Industry Leader – With a long history of creating durable products at an affordable price, Hotpoint is your trusted PTAC brand

PRELIMINARY SPECIFICATIONS – SUBJECT TO CHANGE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>