jlrgear STG-7074-KB 3 In 1 Wireless Charging Clock Instruction Manual

jlrgear STG-7074-KB 3 In 1 Wireless Charging Clock

Specifications

• Input: 5V 3A / 9V 3A
• Phone Charger Output: 5W/7.5W/10W/15W
• AirPods® Charger Output: 5W
• Watch Charger Output: 2.5W
• Charging Standard: Qi™ Wireless
• Charging Distance: 3-8mm
• USB-A Output: 5W
• Power Port: USB-C
• Power Cord: 3FT (1M)
• Net Weight: 124g

Connecting Power

1. Connect USB cable to USB-C port on bottom back of charging clock.
2. Connect to USB power source 5V 3A or greater. For best results and faster charging speeds, connect to 9V 3A USB power source.

Your Devices

1. Fold stand open and place on flat surface.
2. Place smartphone on the phone charging pad to charge wirelessly. LED light will indicate device is charging. Your device will display the charging progress on screen.
3. Place Apple Watch® flat on top of the watch charger as shown.
4. Place AirPods® on the bottom charging pad of the clock to charge wirelessly.
5. Connect to USB-A output to charge or power other small devices.

Setting Clock

1. To set the clock, hold MODE (M) button for 3 seconds and use the up and down arrow keys to set the hour. Tap mode again to adjust the minutes. Hold MODE again to exit time setting mode.

Setting Alarm

1. Short press the mode button for one second until the alarm clock starts to flash. Use the up and down arrow keys to set the hour. Tap mode again to adjust the minutes. Hold MODE again to exit alarm setting mode.
2. Press and hold the up arrow to turn the alarm function on. Press and hold the down arrow to turn the alarm off. Press any button to turn off alarm when it sounds.

Replacing Backup Battery

1. This clock is equipped with a backup battery that will hold time settings during power outages.
2. Clock requires 1 “CR2025” 3V lithium battery (included). To replace, use a screwdriver to open the battery compartment and replace the battery following the polarity markings.

CAUTION! Device must have  enabled charging. Check with manufacturer for compatibility. Never use the charger to charge smartphones with metal cases or metal plates between the case and the phone. Some additional non-metal protective cases may also interfere with proper charging. The charger, phone and accessories will feel warm during or after charging.

WARNING! IMPORTANT CARE AND SAFEGUARDS
Failure to follow the safety instructions can lead to fire, electrical shock, personal injury or property damage and damage to this product.

• Do not use this wireless charger for anything other than it’s intended use
• Always use the specified power
• Always use this product in operating source and voltage
• This product is not intended charge batteries or other devices
• Do not use a voltage converter /temperatures of 32’F (0°C) 95’F (35’C) travel adapter
• Do not handle charging clock, USB power
• If you have an electrical device, such
• Always place the charging clock cord or power source with wet hands
• Do not let dust or other things accumulate as a pacemaker, consult a physician on a sturdy and level surface on charging clock and power cord before using this product.
• This product contains small parts
• Do not place magnetic cards or similar items near this product and is not suitable for children
• Do not use the charging clock if it has
• Keep all foreign objects, small metal
• Do not expose this product to rain, been dropped or damaged in any way
• Never take this device apart and always water or excessive humidity get repaired by a qualified technician pieces and debris away from
• If the charger becomes wet, immediately
• Always unplug the charging clock when charging surfaces at all times unplug it from the power source not in use for a long period of time
• Make sure charging surfaces are clear prior to use and at all times
• Keep charging clock away from heat sources and direct sunlight.

FCC Disclaimer : This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

NOTE : THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT. The ‘Qi’ symbol is a trademark of the Wireless Power Consortium. iPhone, Apple Watch, AirPods and MagSafe are registered trademarks of Apple Inc., registered in the U.S. and other countries. Android is a trademark of Google Inc.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  Caution : Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>