jlrgear Sleep, Relaxation Sleep Sound Mask Installation Guide

jlrgear Sleep, Relaxation Sleep Sound Mask

Specifications

• Range: 30 Ft (10 Meters)
• Power Input: USB 5V / 1A
• Battery Type : Lithium Battery
• Battery Capacity: 200 mAh
• Charging Time : Up to 2 hours
• Playback Time: Up to 10 hours

OVERVIEW

Please see the reverse side for important washing instructions

Charging

• Slide the wireless controller out of the eye mask enough to expose the USB port
• Connect the USB cable to the USB port on the controller and standard SV / lA USB power source (not included). Do not exceed SV / 2A charger
• The power indicator light will turn red while charging and will turn off when complete
• Do not charge with a USB-C PD fast charger. The device may not charge due to higher voltage output and could cause damage to the battery
• Replace the controller making sure control buttons are aligned with stitched buttons on an eye mask

Pairing Sound Mask

• Press and hold the Power/Play/Pause button to turn On
• The indicator will flash red and blue while in paring mode
• Open the Bluetooth®menu on your smartphone and search for new devices
• Connect to SLEEP SOUND MASK. An alert will sound ind1cat1ng 1s connected
• Sound Mask will reconnect to the smartphone automatically after the initial pairing
• If auto-reconnect does not occur then repeat the steps above

Sound/ Music Playback

• Power mask On and connect to a smartphone via Bluetooth®

• Open your favorite sound or music player App on your smartphone.
  Control sound/music playback and volume with your smartphone Use control buttons on a mask to play/pause music, select track, adjust volume, and power On/Off

• Short press the Next / Last Track buttons to select the track.
  Press and hold the Next / Last Track buttons to ad丿ust volume

• Built-in microphone for calls Short press Play/Pause button to answer / end calls

Wearing Mask

• Power mask On, connect to a smartphone, and begin playback
• Wrap the mask around the head with eye covers centered over the eyes.
• Pull straps tight around the head and securely fasten them in place
• Adjust earphones into pos巾on over ears by sliding inside the strap
• Adjust the mask to rest comfortably on the nose and over eyTheThe mask can be used with or without electronics.

Removing Electronics

• Remove earphones one at a time from straps by sliding them out carefully Do not pull hard on wires
• Use your fingers to slide the controller out to one side
• Follow with an earphone that still needs to be removed

Replacing Electronics

• Slide earphones with a longer wire carefully through the center of the mask to the opposite side.
• Follow with the controller by sl1d1ng with fingers and secure in the center of the mask
• Make sure control buttons are aligned with stitched buttons on an eye mask
• Slide earphones into a pocket on straps with speakers facing in toward ears

The illustration shows the sequence of removing electronics. Reverse steps to replace

Cleaning Eye Mask Cover

• Remove electronics completely before cleaning
• Hand wash eye mask with mild soap and water or clean in washing machine
• Air dry only. Do not dry with a dryer
• Allow to air dry completely before replacing electronics

CAUTION: Never dry mask,n dryer Never wash or get electronics wet Permanent damage may occur
WARNING! IMPORTANT CARE AND SAFEGUARDS
Failure to follow the safety instructions can lead to personal injury or property damage and damage to this product

• This product is not suitable for children or individuals with d1sab邮es
• This product contains small parts and 1s, not su, table for children
• Do not use this product for anything other than its intended use
• The product 1s not waterproof
• Do not expose this product to rain, water, or excessive hum心ty
• Do not store this product next to heat sources or in direct sunlight
• Do not handle this product with wet hands
• Extreme hot and/or cold weather may damage this product
• Always use this product 1n operating temperatures of 32° F(0°C) – 95° F(35°C)
• Never take this device apart and always get repaired by a qualified technician
• Do not use this product 1f 1t has been damaged 1n any way
• This product contains one or more internal batteries, please dispose responsibly

This FCCDtsclalmet de, ce comes with part 15 of the FCC Roles. Operation is subject into the following two categories (1) Th,s de, ice,otetfeteoce may oot that case may” harmful desired iotetfeteoce, operation. and (2) NOTE, this THE de, ce mos< MANUFACTURER accept any IS NOT iotetfeteoce RESPONSIBLE time, ed, FOR melodeon ANY RADIO MODIFICATIONS OR TV COULD INTERFERENCE VOID THE CAUSED USER BY AUTHORITY UNAUTHORIZED TO OPERATE MODIFICATIONS THE EQUIPMENT TO THIS EQUIPMENT. SUCH

The tcademaBloetoothks ®owoed wood by Mack Bluetooth and SIG, logos loc, ace, eg, sliced

CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Any questions, please call customer service at 1-800-254-0111
8:30 am – 5pm, PST. Monday – Friday, or email us at customerservice@jIrgear.com

2434 Research Dr., Livermore, CA 94550
© 2024 JLR Gear – Made in China

FAQ

• Q: How do I adjust the volume or switch tracks on the Sleep Sound Mask?
  • A: Use the designated buttons on the device for adjusting volume, switching tracks, or controlling playback.
• Q: What should I do if I have questions or issues with the product?
  • A: Contact customer service at 1-800-254-0111 for assistance with any inquiries or problems related to the Sleep Sound Mask.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>