jlrgear DT6967KB Car Interior Light Strips Instruction Manual

jlrgear DT6967KB Car Interior Light Strips

Product Usage Instructions

Setup

1. Place the product on a stable surface near a power outlet.
2. Ensure the power switch is in the OFF position.
3. Insert the power plug into the outlet.

Operation

1. Fill the product with ingredients according to the user manual.
2. Turn the power switch to the ON position.
3. Select the desired settings using the control panel.
4. Monitor the progress through the viewing window.
5. Once done, switch the power off and unplug the device.

Cleaning and Maintenance

• Always clean the product after each use.
• Use a damp cloth to wipe the exterior and removable parts.
• Refer to the manual for detailed cleaning instructions.

FAQ

• Q: How often should I clean the product?
• A: It is recommended to clean the product after each use to maintain hygiene and prolong its lifespan.
• Q: Can I use this product for both sweet and savory dishes?
• A: Yes, you can use this product for a variety of dishes. Refer to the recipe book for specific suggestions.

overwiew

Specifications

• Bluetooth® 5.3
• Length: 9 Inch x 4 strips
• 48 RGB LEDs (12 LEDs per strip)
• Power Input : 5V / 2A or 12V
• Connector Type: USB-A or 12V plug
• IR Remote: Sound Reactive
• Remote Battery : CR2025 Button Cell

Light Strip Setup

• Choose smooth and hard surfaces in the vehicle to mount LED strips. Smooth plastic and metal are ideal mounting surfaces.
• Position LED strips around the vehicle to make sure power cables can reach mounting locations. There are 2 shorter cables for the front of the cabin and 2 longer cables reach to the rear.
• Run cables in location that do not interfere with vehicle or seat operation.
• Carefully peel off the adhesive backing without removing a clear adhesive layer. The adhesive layer is very thin, and clear and can come off inadvertently while removing backing.
• Apply pressure while sticking the LED strip.
• Connect the USB plug to a 5V / 2A USB power source or 12V power outlet with included power cables.
• Installation Tip: For best results and long-lasting adhesion, go back over the LED strip one more time by carefully running your finger over the entire strip to make sure the strip is securely attached to a mounting surface. Apply pressure to any areas that are not fully attached to the surface until firmly stuck.

BE CAREFUL WHEN PEELING OFF THE BACKING THAT YOU DON’T REMOVE THE CLEAR ADHESIVE LAYER!|

Sound Reactive Remote Control

• Make lights dance to the music!
• Remove the plastic battery protector from the remote control before use.
• Point the remote toward a light that is already set and press the ON button to test.
• Remote controls light up to 30 feet away. Make sure to point the remote at the IR sensor light and that there is a clear line of sight.
• Choose colors, adjust brightness level, or select preset color or color flow light modes.
• Press the music button for a sound-reactive mode that makes lights change colors to sound.
• Place the remote less than 20 inches away from a speaker or other sound source and less than 30 feet away from the lights with clear line of sight.

Scan the above QR code or download the Smart Life App for your lOS® or Android™ device available for free download from the App Store® or Google Play™™

Connecting Smartphone

• Download the Smart Life App from the App Store or Google Play.
• Allow App access. You may choose to register or continue as a guest.
• Connect the light strip to the USB power source. Press and hold a button on the controller until the light strip starts flashing. Discovering devices…
• Tap + in the upper right to add the device.  tile with the quick Add button will automatically appear in the upper screen area if the light is flashing in pairing mode and device is discoverable. Tap the Add button to connect automatically.
• Follow the prompts in the App to connect and proceed to the home screen.
• Select Strip Lights. Lights can connect via Bluetooth®
• Mako citro flashing light strain and smartphone aro nearly.

Advanced App Control

• Advanced lighting controls and customization using the App.
• Tap the power button in the bottom left of the screen to turn the light On/Off.
• Tap color, color preset, and music sync at the bottom of the screen. Each menu has custom light settings.
• Choose the color at the bottom of the screen to select a color from the spectrum. Tap color type and adjust by tapping the wheel.
• Choose at the bottom of screen to select from preset color modes
• Choose music sync at the bottom of the screen. Select microphone sensitivity or select from preset light colors and patterns to customize.
• Choose to access timer menu settings for the lights to automatically turn off at a preset time.

Control lights with a Smart App, or remote control or turn them on and off with a power button.

Replacing Remote Control Battery

• Pinch end of battery tray with finger nail and pull out by sliding.
• Insert new “CR2025” button cell battery with positive side facing upwards in tray.
• Slide battery tray back into remote and test.
• Care Tip: Periodically wipe clean with soft cloth. Never use abrasive cleaning agent or get wet.

WARNING: KEEP AWAY FROM CHILDREN. CAUTION: LED’S ARE VERY BRIGHT. AVOID DIRECT EXPOSURE OF LED LIGHTS TO EYE. INJURY TO EYES MAY OCCUR. DO NOT SHINE IN THE EYES OF OTHERS.

WARNING! IMPORTANT CARE AND SAFEGUARDS
Failure to follow the safety instructions can lead to personal injury or property damage and damage to this product.

• Make sure lights and cables do not interfere with vehicle or seat operation
• Use inside vehicle only, not rated for use outside of vehicle
• Unplug light strips when not in use to avoid draining vehicle battery
• Do not use the lights for anything other than intended use
• Always use the specified power source and voltage
• This product contains small parts and is not suitable for children
• Do not expose this product to rain, water or excessive humidity
• Do not handle power plug or connectors with wet hands
• Do not use lights if they have been dropped or damaged in any way
• Never take this device apart and always get repaired by a qualified technician
• Keep light away from heat sources and direct sunlight

FCC STATEMENT

FCC Disclaimer:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries. Android, Google Assistant, Google Play and the Google Play logo are trademarks of Google Inc. IOS is a registered trademark of Cisco in the U.S. and other countries and is used under license. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.

Any changes or modifications not expressly approve

NOTE: This equipment has been tested and four These limits are designed to provide reasonable protection against harmful interference in a residential installation  .. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipmentoff and on, the useris encouraged to try to correct the interference by one or more of the following measures: v

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>