MEANWELL HLG-150H-12 LED Driver Installation Guide
- July 29, 2024
- MeanWell
Table of Contents
MEANWELL HLG-150H-12 LED Driver
Product Usage Instructions
Installation
- Ensure power is turned off before installation.
- Connect the input wires to the appropriate power source within the specified voltage range.
- Connect the output wires to the LED lighting system following the correct polarity.
- Securely mount the LED driver in a well-ventilated area.
Operation
- Once installed, turn on the power source to activate the LED driver.
- Adjust the voltage and current settings if necessary for your LED lighting system.
- Monitor the LED driver for any irregularities in performance or temperature.
Maintenance
- Regularly inspect the LED driver for any signs of wear or damage.
- Clean the exterior of the LED driver with a soft, dry cloth to remove any dust or debris.
- Ensure proper ventilation around the LED driver to prevent overheating.
FAQ
- Q: Can I adjust the voltage and current settings on all models?
- A: No, voltage and current adjustments are only available for A and AB-type models via the built-in potentiometer.
- Q: What is the maximum number of units that can be connected to a 16A circuit breaker?
- A: For type B circuit breakers, you can connect up to 4 units; for type C circuit breakers, you can connect up to 7 units at 230VAC.
Features
- Constant Voltage + Constant Current mode output
- Metal housing with class I design
- 1P67 / IP65 rating for indoor or outdoor installations
- Function options: output adjustable via potentiometer; 3 in 1 dimming
- Typical lifetime > 62000 hours
- 7 years warranty
Applications
- LED street lighting
- LED high-bay lighting
- Parking space lighting
- LED fishing lamp
- LED greenhouse lighting
- Typ “HL” for use in Class I , Division 2 hazardous (Classified) location.
GTIN CODE
- MW Search: https://www.meanwell.com/serviceGTIN.aspx
Description
HLG-150H series is a 150W AC/DC LED driver featuring the dual mode constant voltage and constant current output. HLG-150H operates from 90 ~ 305VAC and offers models with different rated voltages ranging between 12V and 54V. Thanks to the high efficiency up to 94%, with the fanless design, the entire series can operate for -40°C ~ +90°C case temperature under free air convection. The design of metal housing and IP67/|P65 ingress protection level allows this series to fit both indoor and outdoor applications. HLG-150H is equipped with various function options, such as dimming methodologies, to provide the optimal design flexibility for LED lighting systems.
Model Encoding
SPECIFICATION
NOTE
- All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
- Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
- Tolerance: includes set up tolerance, line regulation and load regulation.
- Please refer to “DRIVING METHODS OF LED MODULE”.
- De-rating may be needed under low input voltages. Please refer to the “STATIC CHARACTERISTIC” sections for details.
- The length of set-up time is measured at the first cold start. Turning ON/OFF the driver may lead to an increase of the set-up time.
- The driver is considered as a component that will be operated in combination with the final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify the EMC Directive on the complete installation. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)
- To fulfill the requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without being permanently connected to the mains.
- This series meets the typical life expectancy of >62,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 80℃ or less.
- Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com.
- The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitudes higher than 2000m(6500ft).
- For any application note and IP waterproof function installation caution, please refer to our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf
Product Liability Disclaimer: For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx
BLOCK DIAGRAM
DRIVING METHODS OF LED MODULE
-
This series is able to work in either Constant Current mode (a direct driveway) or Constant Voltage mode (usually through an additional DC/DC driver) to drive the LEDs.
-
In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems.
-
Should there be any compatibility issues, please contact MEAN WELL.
-
Typical output current normalized by rated current (%)
DIMMING OPERATION
3 in 1 dimming function (for B/AB-Type)
- Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 1 ~ 10VDC, or 10V PWM signal or resistance.
- Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.
- Dimming source current from power supply: 100μA (typ.)
Applying additive 1 ~ 10VDC
- Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):
- Applying additive resistance:
Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follows, or please contact MEAN WELL for other options.
- Using a switch and relay can turn ON/OFF the lighting fixture.
OUTPUT LOAD vs TEMPERATURE(Note.10)
STATIC CHARACTERISTICS
- De-rating is needed under low input voltage
POWER FACTOR(PF) CHARACTERISTIC
TOTAL HARMONIC DISTORTION (THD)
- 48V Model, Tcase at 80℃
EFFICIENCY vs LOAD
- HLG-150H series possess superior working efficiency that up to 94% can be reached in field applications.
- 48V Model, Tcase at 80℃
LIFETIME
MECHANICAL SPECIFICATION
※Blank/D-Type
A-Type
B-Type
AB-Type
WATERPROOF CONNECTION
Waterproof connector
The waterproof connector can be assembled on the output cable of HLG-150H to
operate in dry/wet/damp or outdoor environments.
Cable Joiner
- CJ04 cable joiner can be purchased independently for the user’s own assembly.
- MEAN WELL order No. : CJ04-1, CJ04-2.
Junction Box Option
- Junction box option is available for A / Blank – Type. Please contact MEAW WELL for details.
INSTALLATION MANUAL
- Please refer to: http://www.meanwell.com/manual.html.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>