Sky Wing K2 Upgraded Wireless Headphones User Guide

June 13, 2024
SKY WING

Wing K2 Upgraded Wireless Headphones
User Guide

AFTER-SALES MAIL: dllbkm1@163.com

PACKAGE CONTENTS

Does not include wall charger, please prepare a wall charger with a specification of 5v 0.5-2A for charging

Charging

2.1 Type-C
DO NOT charge the headphone through apple Type-C cable, charge it via the type-C cable which is in includes.
Headphone is charging via Type-C cable, when finished, LED Indicator light will be changed from red (Long bright) to blue (Long bright).

  • Charging time: when charge it for the first time, it should be more than 4 hours and less than 8 hours, to activate the best use of the battery, and after that, each charging only needs 2-3 hours.
  • Low battery: Alarming once for each 3 minutes and accompanied by a ” Low battery please charge” voice prompt.
  • Please disconnect the Type-C cable when the headset is fully charged, since overcharge will shorten the battery life.

2.2 Base

  1. Find the charging pins of the headset and base, and put the headset down.
  2. The LED lights of the base and headphones are red, indicating that they are charging.
  3. After fully charged, the base and headphones of LED lights wilt be green and blue respectively.
  4. Hold the headset close to the base when picking it up. The base and headset will enter an automatic connection state(LED lights of the base and headphones breathe blue). If the LED light of the headset or base flashes red and blue alternately, please refer to the troubleshooting on page 17.

Check your Device’s Output Ports

Connection and Use

NOTE: If the light of the Transmitter or headphone is red and blue alternately and cannot be connected, please refer to page 17 (Troubleshooting).
4.1 Optical Connection (Recommended)

  1.  Remove the plastic caps

  2. Plug in
    Make sure the optical cable connects correctly to your TV.

  3.  Turn on

  4. Get power to the transmitter with the wall charger/PC, then turn on the headset. You will hear the “power on from the headphones.

  5. Pairing LED lights of the base and headphones breathe blue). The blue light on the transmitter remains steady, and the blue light on the headset flashes occasionally. They are paired.

  6. Turn on TN/ and play sound, enjoy it.

NOTE: If not sound, please set the TV System to “Headphone” and TV Audio Format to “PCM”.
The base is connected to a 3.5mm audio cable and an optical cable at the same time, the base will output the 3.5mm audio cable first. if only the optical fiber output is used, the 3.5mm cable should be unplugged.
4.2 RCA(red/white) Connection

  1. Plug in
    Please check whether the RCA interface of your TV is an audio output interface before connecting.

  2. Turn on

  3. Get power to the transmitter with the wall charger/PC, then turn on the headset You will hear the “power on” from the headphones.

  4. Pa irking(LED lights of the base and headphones breathe blue). The blue light on the transmitter remains steady, and the blue light on the headset flashes occasionally. They are paired.

  5. Turn on TV and play sound, enjoy it

NOTE: If not sound, please set the TV System to “Headphone” and TV Audio Format to “PCM”.
4.3 3.5mm Connection

  1. Plug in

  2. Term on
    1. Get power to the transmitter with the wall charger/PC, then turn on the headset. You will hear the “power on” from the headphones.
    2. Pacing LED lights of the base and headphones breathe blue). The blue light on the transmitter remains steady, and the blue light on the headset flashes occasionally. They are paired.
    3. Turn on TV and play sound, enjoy it.

NOTE: If not sound, please set the TV System to “Headphone” and TV Audio Format to “PCM”.
4.4 Connect to mobile phone bluetooth

  1. Please confirm whether the LEO light of the headset is red and blue alternately before connecting. If not, please long press Multifunction Key for 5 seconds. Then turn on the mobile phone bluetooth. Keep the headset as close to the Phone as possible.
  2. Search for a device named ‘IiIKM500° on your phone, then click connect.
  3. A few seconds later the connection was successful The LEO of headphone is blue and flashes slowly, and the phone shows that it Is connected. You Can hear it In your headphones: Your headset is connected.

NOTE: Need to manually connect to mobile phone every time. When the mobile phone and the transmitter are turned on at the same time, the headset will automatically connect to the transmitter.

TV Setting

NOTE: Other TVs are similar to the settings. Or contact your TV manufacturer for more details.

|
---|---
|

Operating Instructions

Multifunction Key

  1. Pause/Play music
  2. Clear pairing history: Press the Multifunction key and ” -” key at the same time. Unable to connect again after clearing, you need to re-pair. This function cannot be used in the call state.
  3. Pairing mode: Long press the Multifunction Key for 5 seconds
  4. Voice dialing system: Long press the Multifunction key for 1 second. You can hear the beep in the headphone. (Only available when connected to the mobile phone)
  5. Restart the headphone: Long press the Multifunction key for 10 second.
  6. DUT model: in the pairing mode, press the Multifunction key and “-” key at the same time for 5 seconds to enter the DUT mode. Exit DUT mode after turning off the headset.

Equalizer Mode Key
In the connected state, click the EQ mode key to switch to different EQ modes to experience different sound effects.
Witching sequence: Pop-Rock-Movie. Defaults 10 popular mode at the startup.

Power On/Off Key:
After the startup, it automaticaly enters the pairing state when no device is bound. Enter the connection back state when there is a bound device.
Multifunction Key

  1. Clear pairing history: Please turn off the paired headset first, and long press the Multifunction Key for 10 seconds to clear all connected devices ( Red and blue lights are on for 3 seconds at the same time ) . After clearing, it will automatically enter the pairing state.
  2. Pairing mode: Long press the Multifunction Key for 5 seconds.

Automatic connection:
After power on, the base will automatically connect to the last successfully paired device when there is a pairing record. The base will automatically connect to the bound device after binding
Note: After Clear pairing history, you need to re-pair and bind the device, otherwise the base will not be able to enter the automatic connection state when it is turned off and then turned on.

Replace the bound device

The supporting equipment has been bound at the factory, and the base and the headset can be automatically connected after turning on. If you need to bind the base with another BKI4500 headset, please refer to the following steps:

  1. Clear pairing history: Please turn off the paired headset first. Then long press the Multifunction Key for 10 seconds, the red and blue rights are on for 3 seconds at the same time, which means that the base has been emptied successfully.
  2. Phal The base automatically enters the pairing mode after clearing successfully, please check whether the LED light of the headset is flashing red and blue alternately, if not, please long press the Multifunction Key for 5 seconds.
  3. Connected successfully: The blue LED light of the base is always on, and the blue LED light of the headphone flashes occasionally. You can hear the sound. Represents a successful connection.
  4. Headphones bound to the base: After the pairing is successful, you need to bind the headset to automatically connect the next time you turn it on. please double-click the base to bind (the LED light of the base will flash red 5 times).
    NOTE: Re-binding another headset may result In prolonged connection times In the future.

Troubleshooting

Issue Solution
Unable to automatically connect due to disconnection due to distance. If not

connected, please check whether the headphone and transmitter are in pairing mode (red and blue lights flash alternately), if net. please long press the Multifunction Key for 5 Seconds of the transmitter and ihe headphone to enter the pairing mode and connect.
Password reminder| If a password prompt appears when connecting the headset, you can try entering 00018888, 111I, or 1234.
How to charge| 1. 8104500 can be charged by car charger, travel charger, computer US8, etc. with a DC voltage of SY and a current of more than Soon
2. use the base to charge.
Don’t connect| 1. Red and bluealternately of headphone/ Breathing blue of base:
long Press the Multifunction Key on the base For 5 seconds until the LED lights flash red and due alternate* they will automatically connect.
2. Breathing blue of headphone/Red and blue alternately of base:
Long Press the Multifunction Key on the headphone for 5 seconds untap the LED lights gash red and blue alternate they will automatically connect.
3. Auto connect failed:
Please refer to uoubleshootng point 0 to reconnect. After successful connectome, please double. click the base to on Ate LED light of the base will flash red 5 times).

LED Indication

Headphone

Low battery: Red flash
Charging: Steady Red
Full charged: Steady blue
Pairing status: Red and blue alternately
Automatic connection status: Breathing blue
Standby after connecting the device: Blue light flashes once every 10 seconds
Pairing successful: Blue light flashes two every 10 seconds
Calling: Blue light flashes once every 10 seconds
Clear pairing history: Steady red for 1 second
DUT mode: Steady Red
Link loss: Breathing blue

Base

Pairing status: Red and blue alternately
Pairing successful: Steady blue
Charging: Steady Red
Full charged: Steady green
Clear pairing history: Red and blue lights are on for 3 seconds at the same

time
Automatic connection status:| Breathing blue

Product specifications

10.1 Headphone

Bluetooth Version V5.2
Frequency Range 2.402-2.48OG-1z
Bluetooth Chip 8925B2
Wireless Range 10in
Bluetooth Protocol HSP HFP A2DP AVRCP
Decoding Method mSBC MC
Built-In Battery 420mAtr3.7V
Charging Time 2-3 Hour
Standby Time About 400 hours
Working Hours About 45 hours(70%. volume)
Headphone Weight 202g
Headphone Size 19.2`17.311.03cm

10.2 Base

Bluetooth Version V5.0
Frequency Range 2.402-2.4B0GHz
Bluetooth Protocol A2DP AVRCP
Bluetooth Chip BT8818
Wireless Range 30m
Decoding Method SBC
Base Site 17*10’4.07cm
Base Weight 145g

After-Sale Service

1 Year Full Warranty
Any problem? Reach out to us at dltbkm1@163.com, our specialists will be sincere to help you.
Your satisfaction is our number one priority!
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

E-mail: dillskml@l63.com
Address: jinglongdadao 16hao dong sheng shi dal 6 A 25D ping shan qu Shenzhen guangdong, China
Bluetooth Headset FCC ID: WSG-K2 ;
Bluetooth transmitter FCC ID: WSG-K2A

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals