ICON PROCESS CONTROLS PA5000 Audible and Visual Alarm Plus Display Controller Owner’s Manual

July 22, 2024
ICON PROCESS CONTROLS

ICON PROCESS CONTROLS PA5000 Audible and Visual Alarm Plus Display

Controller

Specifications

General|
---|---
Display| Displayed Values Stability Transmission Parameter Protection
Class
Input Signal | Supply| Standard Voltage
Current: 4-20mA (std.) | 0-20mA | 0-5V | 0-10V
85 – 260V AC/DC | 16 – 35V AC, 19 – 50V DC*
Output Signal | Supply| Standard Voltage
4-20mA 24VDC
Performance| Accuracy
Accuracy According to IEC 60770 – Limit Point Adjustment |
Non-Linearity | Hysteresis | Repeatability
Temperatures| Operating Temperatures
Materials | Wetted| Housing
Polycarbonate
Part Number| PA5000

Product Usage Instructions

Basic Requirements and User Safety Guidelines

  • Do not use the unit in areas threatened with excessive shocks, vibrations, dust, humidity, corrosive gases, and oils.
  • Avoid using the unit in areas where there is a risk of explosions.
  • Avoid using the unit in areas with significant temperature variations, exposure to condensation, or ice.
  • The manufacturer is not responsible for damages caused by inappropriate installation or not maintaining proper environmental conditions.
  • If there is a risk of serious threats due to unit malfunction, use additional systems to prevent accidents.
  • Ensure to switch off and disconnect the unit from the power supply before troubleshooting.
  • Do not attempt to disassemble, repair, or modify the unit yourself.

Programming the 4-20mA Input
Steps:

  1. Press ESC/MENU Button for 3 Sec.
  2. Press DOWN Arrow 2 times.
  3. Press ENTER Button.
  4. Press DOWN Arrow 4 times.
  5. Press UP or DOWN Arrow to adjust value.
  6. Press ENTER Button for 2 Sec.
  7. Press DOWN Arrow.
  8. Press ENTER Button.
  9. Press ENTER Button for 2 Sec.
  10. Press ESC/MENU Button twice.

Quick Start Manual

Read the user’s manual carefully before starting to use the unit. Producer reserves the right to implement changes without prior notice.

Symbol Explanation

This symbol denotes especially important guidelines concerning the installation and operation of the device. Not complying with the guidelines denoted by this symbol may cause an accident, damage or equipment destruction.

Basic Requirements | User Safety

  • Do not use the unit in areas threatened with excessive shocks, vibrations, dust, humidity, corrosive gasses and oils.
  • Do not use the unit in areas where there is risk of explosions.
  • Do not use the unit in areas with significant temperature variations, exposure to condensation or ice.
  • The manufacturer is not responsible for any damages caused by inappropriate installation, not maintaining the proper environmental conditions and using the unit contrary to its assignment.
  • If in the case of a unit malfunction there is a risk of a serious threat to the safety of people or property additional, independent systems and solutions to prevent such a threat must be used.
  • The unit uses dangerous voltage that can cause a lethal accident. The unit must be switched off and disconnected from the power supply prior to starting installation of troubleshooting (in the case of malfunction).
  • Do not attempt to disassemble, repair or modify the unit yourself. The unit has no user serviceable parts.
  • Defective units must be disconnected and submitted for repairs at an authorized service center.

Specifications

General

Display| LED | 4 x 20mm High | Red | Adjustable Brightness
Displayed Values| -999 ± 9999
Stability| 50 ppm | °C
Transmission Parameter| 1200…115200 bit/s, 8N1 / 8N2
Protection Class| NEMA 4X | IP67
Input Signal | Supply

Standard| Current: 4-20mA (std.) | 0-20mA | 0-5V | 0-10V
Voltage| 85 – 260V AC/DC | 16 – 35V AC, 19 – 50V DC*
Output Signal | Supply

Standard| 4-20mA
Voltage| 24VDC
Performance

Accuracy| 1% @ 25°C One Digit
Accuracy According to IEC 60770 – Limit Point Adjustment | Non-Linearity | Hysteresis | Repeatability
Temperatures

Operating Temperatures| -40 – 158°F | -40 – 70°C
Materials | Wetted

Housing| Polycarbonate
Part Number| Input| Display
---|---|---
PA5000| 4-20mA| Single

Front Panel Description

ICON-PROCESS-CONTROLS-PA5000-Audible-and-Visual-Alarm-Plus-Display-
Controller- \(2\)

Wiring Diagram

Function of Push Buttons

ICON-PROCESS-CONTROLS-PA5000-Audible-and-Visual-Alarm-Plus-Display-
Controller- \(4\)

Programming 4-20mA Input

ICON-PROCESS-CONTROLS-PA5000-Audible-and-Visual-Alarm-Plus-Display-
Controller- \(5\)

Programming 4-20mA Output ICON-PROCESS-CONTROLS-PA5000-Audible-and-
Visual-Alarm-Plus-Display-Controller- \(6\)

Calculating 4-20mA Input

SENSOR TYPE 20mA Set Point
Submersible Range of sensor / Specific Gravity = 20mA
Ultrasonic Tank Height
Radar Tank Height

Programming Relays

ICON-PROCESS-CONTROLS-PA5000-Audible-and-Visual-Alarm-Plus-Display-
Controller- \(1\)

24-0188 © Icon Process Controls Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals