ICON PROCESS CONTROLS ShoPro Series Level Display and Controller Instruction Manual
- August 22, 2024
- ICON PROCESS CONTROLS
Table of Contents
- Safety Information
- Technological Progress
- Product Description
- Features
- Technical Specifications
- Installation Instructions
- Wall Mounting
- Pipe Clamp Installation
- Quick Wire Connection
- Internal Wire Connection
- Front Panel Description
- Programming Display
- Alarm Set
- Warranty, Returns & Limitations
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ShoPro® Series
Level Display | Controller
Operating Manual
Safety Information
| Warning | Caution | Danger
Indicates a potential hazard. Failure to follow all warnings may lead to
equipment damage, injury, or death
---|---
| Note | Technical Notes
Highlights additional information or detailed procedure.
| IMPORTANT!
indicates situations or cases which, if not avoided, could result in damage or
failure of the Products equipment.
| Do Not Use Tools
Use of tool(s) may damage product beyond repair and potentially void
product warranty.
Basic Requirements & User Safety
Do not use the unit in areas threatened with excessive shocks, vibrations,
dust, humidity, corrosive gasses and oils.
Do not use the unit in areas where there is risk of explosions.
Do not use the unit in areas with significant temperature variations, exposure
to condensation or ice.
Do not use the unit in areas exposed to direct sunlight.
Make sure that the ambient temperature (e.g. inside the control box) does not
exceed the recommended values. In such cases forced cooling of the unit must
be considered (e.g. by using a ventilator).
The manufacturer is not responsible for any damages caused by inappropriate
installation, not maintaining the proper environmental conditions and using
the unit contrary to its assignment.
Installation should be conducted by qualified personnel . During installation
all available safety requirements should be considered.
The fitter is responsible for executing the installation according to this
manual, local safety and EMC regulations.
GND input of device should be connected to PE wire;
The unit must be properly set-up, according to the application. Incorrect
configuration can cause defective operation, which can lead to unit damage or
an accident.
If in the case of a unit malfunction there is a risk of a serious threat to
the safety of people or property additional, independent systems and solutions
to prevent such a threat must be used.
The unit uses dangerous voltage that can cause a lethal accident. The unit
must be switched off and disconnected from the power supply prior to starting
installation of troubleshooting (in the case of malfunction).
Neighboring and connected equipment must meet the appropriate standards and
regulations concerning safety and be equipped with adequate overvoltage and
interference filters.
Do not attempt to disassemble, repair or modify the unit yourself. The unit
has no user serviceable parts. Defective units must be disconnected and
submitted for repairs at an authorized service center.
The unit is designed for operation in an industrial environment and must not
be used in a household environment or similar.
Technological Progress
The manufacturer reserves the right to revise, alter, or modify the flow meter
to the most current technology without special prior notice.
Further information about the latest updates and potential additions to these
operating instructions are available from
www.iconprocon.com
Product Description
The ShoPro® Series Flow Display & Batcher is the industry’s most rugged and
reliable wall-mount remote display. The ShoPro ®Series will display both Flow
Rate and Flow Total up to 16 digits.
The ShoPro® Series comes as a complete all-in-one unit, out of the box it is
ready to use. Included is a bright LED Display, NEMA 4X Enclosure,
Polycarbonate Faceplate, Cord Grips and Plastic Captive Screws.
The industrial design ensures that it will withstand the industry’s most
corrosive environments. Available with Two 5A Relay + 4-20mA Output
Features
All-in-One | Out of the Box Ready to Use
Visual Alarm – High | Low Level
NEMA 4X Enclosure
New Easy-Learn® Programming
SunBright Technology for Outdoor Applications
No Assembly Required
2 Wire Cord Grips – No Tools Required
Corrosion Resistant Thermoplastic
Two 5A Relay + 4-20mA Output
Flow Rate and Flow Total up to 16 digits
Working Principle
Technical Specifications
General
Display| LED | 5 x 13mm High | Red
Displayed Values| -99999 ± 99999
Stability| 50 ppm | °C
Transmission Parameters| 1200…115200 bit/s, 8N1 / 8N2
Protection Class| NEMA 4X | IP67
Input Signal | Supply
Standard| Current : 4-20mA
Voltage| 85 – 260V AC/DC 16 – 35V AC, 19 – 50V DC
Output Signal | Supply
Standard| 2 x Relays 5A | +4-20mA
Voltage| 24 VDC
Passive Current Output| 4-20mA (Operating Range Max. 2.8 – 24mA)
Performance
Accuracy| 0.1% @ 25°C One Digit
Accuracy According to IEC 60770 – Limit Point Adjustment | Non-Linearity |
Hysteresis | Repeatability
Temperatures
Operating Temperatures| -40 – 158°F | -40 – 70°C
Materials
Housing| ABS | Polycarbonate
Installation Instructions
The unit has been designed and manufactured in a way assuring a high level of
user safety and resistance to interference occurring in a typical industrial
environment. In order to take full advantage of these characteristics
installation of the unit must be conducted correctly and according to the
local regulations.
Read the basic safety requirements on page 3 prior to starting the
installation.
Ensure that the power supply network voltage corresponds to the nominal
voltage stated on the unit’s identification label.
The load must correspond to the requirements listed in the technical data.
All installation works must be conducted with a disconnected power supply.
Protecting the power supply connections against unauthorized persons must be
taken into consideration.
UNPACKING
After removing the unit from the protective packaging, check for
transportation damage. Any transportation damage must be immediately reported
to the carrier. Also, write down the unit serial number located on the housing
and report the damage to the manufacturer.
User’s Manual
Warranty
Wall Mounting
Pipe Clamp Installation
Quick Wire Connection
Internal Wire Connection
Wiring to a Loop Powered Display : Shielded cable is recommended for
control loop wiring.
Use the Red wire as the (+) and the Black wire as the (-).
Front Panel Description
Symbols & Functions of Push Buttons:
Programming Display
dSPL = Low Value – Empty or Lowest Liquid Level – Factory Default is 0
dSPH = High Value – Enter Figure for Maximum Tank Fill Height
Alarm Set
Warranty, Returns & Limitations
Warranty
Icon Process Controls Ltd warrants to the original purchaser of its products
that such products will be free from defects in material and workmanship under
normal use and service in accordance with instructions furnished by Icon
Process Controls Ltd for a period of one years from the date of sale of such
products. Icon Process Controls Ltd obligation under this warranty is solely
and exclusively limited to the repair or replacement, at Icon Process Controls
Ltd option, of the products or components, which Icon Process Controls Ltd
examination determines to its satisfaction to be defective in material or
workmanship within the warranty period. Icon Process Controls Ltd must be
notified pursuant to the instructions below of any claim under this warranty
within thirty (30) days of any claimed lack of conformity of the product. Any
product repaired under this warranty will be warranted only for the remainder
of the original warranty period. Any product provided as a replacement under
this warranty will be warranted for the one year from the date of replacement.
Returns
Products cannot be returned to Icon Process Controls Ltd without prior
authorization. To return a product that is thought to be defective, go to
www.iconprocon.com, and submit a customer return
(MRA) request form and follow the instructions therein. All warranty and non-
warranty product returns to Icon Process Controls Ltd must be shipped prepaid
and insured. Icon Process Controls Ltd will not be responsible for any
products lost or damaged in shipment.
Limitations
This warranty does not apply to products which: 1) are beyond the warranty
period or are products for which the original purchaser does not follow the
warranty procedures outlined above; 2) have been subjected to electrical,
mechanical or chemical damage due
to improper, accidental or negligent use; 3) have been modified or altered; 4)
anyone other than service personnel authorized by Icon Process Controls Ltd
have attempted to repair; 5) have been involved in accidents or natural
disasters; or 6) are damaged during return shipment to Icon Process Controls
Ltd reserves the right to unilaterally waive this warranty and dispose of any
product returned to Icon Process Controls Ltd where: 1) there is evidence of a
potentially hazardous material present with the product; or 2) the product has
remained unclaimed at Icon Process Controls Ltd for more than 30 days after
Icon Process Controls Ltd has dutifully requested disposition. This warranty
contains the sole express warranty made by Icon Process Controls Ltd in
connection with its products. ALL IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION, THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSLY DISCLAIMED. The remedies of repair or replacement as
stated above are the exclusive remedies for the breach of this warranty. IN NO
EVENT SHALL Icon Process Controls Ltd BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING PERSONAL OR REAL PROPERTY OR FOR
INJURY TO ANY PERSON. THIS WARRANTY CONSTITUTES THE FINAL, COMPLETE AND
EXCLUSIVE STATEMENT OF WARRANTY TERMS AND NO PERSON IS AUTHORIZED TO MAKE ANY
OTHER WARRANTIES OR REPRESENTATIONS ON BEHALF OF Icon Process Controls Ltd.
This warranty will be interpreted pursuant to the laws of the province of
Ontario, Canada.
If any portion of this warranty is held to be invalid or unenforceable for any
reason, such finding will not invalidate any other provision of this warranty.
We Measure & Control
All Kinds of Corrosive Liquid S#*%
Industry’s Most Extensive Line of Corrosion-Free instrumentation Equipment.
For additional product documentation and technical support
visit www.iconprocon.com
e-mail: sales@iconprocon.com
support@iconprocon.com
Ph: 905.469.9283
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>