PROLED LL800xx2xP Ed Panel Premium Installation Guide

PROLED LL800xx2xP Ed Panel Premium

Specifications

• Product Name: PROLED LED PANEL 600-x PREMIUM
• Models: L800xx2xP and L800xx2xPD
• Dimensions: 600-x
• Type: LED Panel
• Quality: Premium

Product Usage Instructions

Step 1: Unboxing
Remove the LED panel from the packaging carefully to avoid any damage.

Step 2: Installation
Mount the LED panel securely on a flat surface using the provided mounting hardware. Ensure it is properly aligned to avoid any issues during operation.

Step 3: Power Connection
Connect the LED panel to a power source following the manufacturer’s guidelines. Make sure the power supply matches the panel’s requirements.

Step 4: Testing
Turn on the LED panel and test its functionality. Check for any flickering or abnormalities in the light output.

Frequently Asked Questions (FAQ):

• Q: What is the recommended mounting height for the LED panel?
  

  • A: The recommended mounting height for optimal performance is between 2.5 to 3 meters above the ground.

• Q: Can the LED panel be dimmed?
  

  • A: Yes, the LED panel supports dimming functionality. Refer to the user manual for instructions on how to dim the panel.

• Q: What is the warranty period for the PROLED LED PANEL 600-x PREMIUM?
  

  • A: The warranty period is 2 years from the date of purchase. Please retain your proof of purchase for any warranty claims.

PROLED LED PANEL 600-x PREMIUM L800xx2xP and L800xx2xPD

Characteristics

• SMD CHIP Warm White or Neutral White
• Power supply 110-240 VAC, 50/60 Hz, 40 Watt (600-4) or 47 Watt (600-5)
• LED-power 35 Watt (600-4) or 40 Watt (600-5)
• Metals housing square white
• Panel PMMA white Opal (Primatial surface UGR<19)
• Beam angle 120°
• Constant current driver 1050 mA (600-4) or 1200 mA (600-5) already included
• L800xx2xPD Version: Dimmable with DALI oder PUSH-DIM
• DALI-features: up to 64 single units, up to 16 groups, Status requests
• Operating temperature range -10° C till +45° C
• CE compliant with applicable European directives

Warning

1. For indoor use only
2. Please ensure that the packaging is disposed of in a safe environment
3. If cable is defected, do not use the luminaire
4. We do recommend that a qualified electrician should be used to install the products
5. Do not look at the lighted lamp directly

Safety indices
Be sure to have a qualified electrician complete installation. The customer is not entitled to claim for any lights installed without observing European safety directives. The manufacturer is then discharged from liability when damage is caused by improper use or installation. If any luminaire is subsequently modified, the person responsible for the modification shall be considered as manufacturer. Do not cover lamp with heat-insulating materials. For indoor use only. Protection class IP40.

Installation

Please follow the sequence of installation step by step. Non-observance can lead to damage of LED.

1. Switch off the electricity at the mains before commencing installation or lamp change and (if a fuse box is installed) remove the appropriate circuit fuse to avoid accidental switching on of the mains supply.
2. Connect the constant current driver 1050 mA (600-4) or 1200 mA (600-5) (secondary side)
3. Connect connector to power supply (110-240VAC)
4. Make sure all connections are tight with no loose strands
5. Ensure fire regulations are not breached when fitting your lights
6. If you are in any doubt regarding these instructions, consult a qualified electrician

Please follow the sequence, if not destroying of LED:

Mounting possibilities

Recessed mounting

First check if the recessed ceiling meets the requirements:

Panel size  Channel dimension           Weight 595 x 595 mm 580 x 580 mm ±1 mm ca. 4 kg

622 x 622 mm  605 x 605 mm ±1 mm        ca. 4,2 kg

| Take out a ceiling panel

---|---
Insert the panel under a tilt of around 30-45°

| Check that panel rests everywhere with entire surface. Side distance can’t be more than 3mm, otherwise the luminaire may fall down.

Fixing with spring mounting clips

Make a cutout in the suspended ceiling according to below dimensions:

Panel size  Needed cutout  Weight 595 x 595 mm 575 x 575 mm ±3 mm  ca. 4 kg

622 x 622 mm  600 x 600 mm ±3 mm       ca. 4,2 kg

The ceiling must have a thickness of min. 1-2 cm, else the luminaire may fall down.

| Insert one side with spring mounting clip into ceiling

---|---
Lift up the opposite spring mounting clips and insert the luminaire.

ATTENTION: Driver can’t lay on the luminaire

| Adjust the lamp so that it covers the ceiling cut.

Rope suspension

Drill holes Ø6mm, 35mm deep. Distance according to slots

Ceiling thickness must be min. 50 mm, else the luminaire might fall down

| Insert the dowel and make sure it is installed flush

---|---
Put the rope end into flange and make sure, that a rope end secure exists.

| Fix the flange at the ceiling

Attach the hangers to the luminaire. The safety lock must be closed, otherwise the luminaire might fall down.

| Insert the ropes into the fixings.

Align the luminaire in the desired height and| Distance between rope fixings
horizontally.|
| Panel size      Rope distance
| 595 x 595       535 mm

622 x 622       550 mm

Frame mounted on ceiling

Technical amendments reserved

• MBN GmbH, Balthasar-Schaller-Str. 3, 86316 Friedberg – Germany
• www.proled.com

References

• PROLED: proled.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>