PROLED L51511 Dmx Pwm Dimmer Rgb Din Rail 3 Kanal User Manual
- July 21, 2024
- PROLED
Table of Contents
PROLED L51511 Dmx Pwm Dimmer Rgb Din Rail 3 Kanal
Specifications:
- Model: PROLED DMX PWM DIMMER RGB DIN RAIL 3-CHANNEL
- Input Voltage: DC 5 – 24 V
- Output Voltage: DC 5 – 24 V
- Output Current: max. 3x 5 A
- Output Power: 75 W / 180 W / 360 W (5V / 12 V / 24 V)
- Dimensions: 100mm x 112mm x 24mm
- Net Weight: 120 g
Product Description:
The PROLED DMX PWM DIMMER RGB DIN RAIL 3-CHANNEL is a versatile dimmer
suitable for controlling RGB lighting setups with DIN rail mounting
capabilities. It features an OLED display, PWM frequency of 850 Hz, and
various test programs for easy setup.
Product Features:
- OLED Display
- DIN Rail Mounting on TS-35/7.5 or TS-35/15 rails
- PWM Frequency: 850 Hz
- Test Programs
- IP Rating: IP20
Usage Instructions
DMX Mode:
To set the address in DMX mode, follow these steps:
- Select the address using the +/- buttons.
- Press the “M” button to confirm the address.
Self-test Mode:
The dimmer has various self-test modes that can be accessed through the
digital display. Use the + and – buttons to navigate between different test
programs.
LED Power Selection:
The output current can be adjusted from 0 to 15 A, allowing for different
power outputs based on the LED voltage. For example, at 5 VDC, the power
output can range from 0 to 75 W.
FAQ:
-
Q: What should I do if the device is damaged during transport?
A: If the device is damaged during transport, please report it to your supplier immediately before taking any action. -
Q: What is the warranty coverage for this product?
A: We provide free repair or replacement within one year from the purchase date for quality problems if the product has been used according to the user manual.
Preface
Thank you for choosing PROLED DMX PWM DIMMER RGB DIN RAIL 3-CHANNEL. Before
installation and use, we strongly recommend you to read this manual carefully.
If the device has been damaged during transport, please report this to your
supplier immediately. Please don’t take any action without contacting your
supplier first
Limited Warrenty
In case of quality problems we provide free repair or replacement within one year from the day of purchase, if this product has been used properly in accordance with the user’s manual, except in following cases:
- Any defects caused by wrong operation.
- Any damages caused by unauthorized removal, maintenance, modifying, incorrect connection and replacement of chips.
- Any damages due to transportation, vibration etc. after purchase.
- Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage.
- Any damages caused by negligence, inappropriate storing at high temperatures and humidity or near harmful chemicals.
- Product has been updated
Safety Warnings
- Please don’t install this dimmer during thunderstorms, intense magnetic or high-voltage electrical fields. To reduce the risk of component damage and fire caused by a short circuit, make sure, that all connections are correct.
- Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
- Check voltage and power requirements of the dimmer as well as the polarity of the power supply.
- Never connect any cables while power is on and always assure correct connections to avoid short circuits before switching on.
- Never attempt any repairs yourself; otherwise the manufacturer’s warranty will be void.
- For update information please consult your supplier.
Product Description
PROLED DMX PWM DIMMER RGB DIN RAIL 3-CHANNEL allows dimming of LED-luminaires
or Flex Strips which use up to 3 channels. Setup or starting of Test-Programs
can be done by using 3 buttons at the dimmer.
Technical data
- Modell PROLED DMX PWM DIMMER RGB DIN RAIL 3-CHANNEL
- Input voltage DC 5 – 24 V
- Output voltage DC 5 – 24 V
- Output current max. 3x 5 A
- Output power 75 W / 180 W / 360 W (5V / 12 V / 24 V)
- Ambiente temperature -10°C – 45°C
- Dimensions 35 mm × 67 mm x 112 mm (BxTxH)
- Net-weight 120 g
Specifications
- OLED-Display
- DIN RAIL installation on TS35/7.5 or TS35/15 rail or with screws
- PWM frequency 850 Hz
- Test programs
Dimensions
Connections
Technical amendments reserved
Usage
DMX Mode Address setting:
First press in DMX-Mode “+” or “-” key to enter address setting. As soon as
all 3 digits are blinking, you can set the DMX-address. Address range 001 –
512.
Short press + , slowly increasing, long press + , quick increasing of values.
Short press – , slowly decreasing, long press – , quick decreasing of values.
Short press M to quit.
-
Long press of M and + key at the same time, set a linear brightness curve (C-L).
-
Long press of M and – key at the same time, set a logarithmic brightness curve (C-E).
-
Long press of + and – key at the same time, shows the present brightness curve (C-L or C-E).
Selftest Mode.
Long press of “M”-key to enter the selftest mode.
Changing of programs by pressing + – keys.
| No. | Digital Display (+/- press to change) | Mode | Description |
|---|---|---|---|
| 1 | P-1 | RED | |
| 2 | P-2 | GREEN | |
| 3 | P-3 | BLUE | |
| 4 | P-4 | YELLOW | RED + GREEN = YELLOW |
| 5 | P-5 | PURPLE | RED + BLUE = PURPLE |
| 6 | P-6 | TURQUOISE | GREEN + BLUE = TURQUOISE |
| 7 | P-7 | WHITE | RED + GREEN + BLUE = WHITE |
| 8 | P-8 | 7 colour change | Fixed speed, 1 colour per second |
| 9 | P-9 | 7 colour smooth | Fixed speed, colour change 2 sec., wait time 1 |
sec. until colour change
Restore factory default: Long press of M + – keys together set back the factory default values. Display shows “RES”.
Factory default: DMX Mode, DMX-Startaddress is 1, Gamma curve,
Selftest No. 1 is set.
Technical amendments reserved
Connection diagram
LED chose of voltage
Voltage output is always same as voltage input.
If the luminaire need 5 VDC, please choose a power supply with 5 VDC. If the
luminaire need 12 VDC, please choose a power supply with 12 VDC. If the
luminaire need 24 VDC, please choose a power supply with 24 VDC.
LED chose of power
- Output current can of load has a range of 0 – 15 A.
- At 5 VDC the power output can be between 0 – 75 W.
- At 12 VDC the power output can be between 0 – 180 W.
- At 24 VDC the power output can be between 0 – 360 W.
- The choosen power should be min. 20% above the connected load.
- The more power you have, the better it works.
- Technical amendments reserved
MBN GmbH, Balthasar-Schaller-Str. 3, 86316 Friedberg – Germany www.proled.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>