RAB xxR-xx-9CCT-120-W Flush Mount Ceiling Light Instructions
- July 15, 2024
- RAB
Table of Contents
RAB xxR-xx-9CCT-120-W Flush Mount Ceiling Light Instructions
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
RAB fixture must be wired in accordance with the National Electrical Code and
all applicable local codes.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED.
TO PREVENT ELECTRICAL SHOCK, POWER SHOULD BE TURNED OFF AT THE FUSE BOX
BEFORE INSTALLATION.
SAFETY WARNINGS:
Read all product labels and directions.
- WARNING – Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
- Installation should be performed only by a qualified electrician in accordance with the National Electrical Code and relevant local codes. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
- WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- INSTALLATION SHOULD ONLY BE PERFORMED AFTER POWER TO THE FIXTURE HAS BEEN DISCONNECTED.
- These instructions shall be included on an information sheet packaged with each unit.
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
WHAT’S IN THE BOX
TOOLS NEEDED
Installation with J-BOX A screw driver is needed for installation
INSTALLATION WITH J-BOX
- Make sure the POWER IS TURNED OFF at the source to the J-box in which you are installing the product.
- Disassemble the surface mount cover(Fig.1)
- Select desired CCT level using switch(Fig.2)
- Insert screws into J-Box holes, leaving about 15mm of space between the screw heads and J-Box. (Fig.3)
- Wire the surface mount, white-white, black – black. Once wire connections are made, secure each with a wire nut. (Fig.4)
- Lift fixture to ceiling and carefully tuck wires into J-Box. Align keyholes on surface mount with screws, then twist fixture until the crews engage the narrow end of the keyholes. Tighten screws to secure. (Fig.5)
- Reassemble the lamp cover. (Fig.6) Caulk around the mounting surface edge with silicone sealant (Fig.7)
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
Cranbury, New Jersey 08512 USA
CRVFA-IN-0821
Easy Answers
rablighting.com
Visit our website for product info
Tech Help Line
Call our experts: 888 722-1000
e-mail
Answered promptly- sales@rablighting.com
Free Lighting Layouts
Answered on line or by request
RAB WARRANTY: RABs warranty is subject to all terms and conditions found at rabighting.com/warranty.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>