Trudian Wiegand Access Controller User Manual
- July 11, 2024
- Trudian
Table of Contents
Trudian Wiegand Access Controller
Specifications
- Input: DC12V/500MA
- Working Mode: Networked, offline multi-mode selectable
- Card Issuing Mode: Management platform card issuing
- Card Capacity: 40000
- Password Capacity: 20000
- Working Temperature: -20°C to 70°C
- Relative Humidity: 20% to 93%
- Size: 16210538.5mm
Product Overview
The Wiegand Access Controller is designed for access control applications with a capacity for up to 40000 cards and 20000 passwords. It operates on DC12V/500MA input power and supports networked and offline working modes. The device allows card issuing through a management platform and can function in various temperature and humidity conditions.
Controller Interface Description
The controller interface includes connections for power input, Wiegand Readhead, indicator LED, locks, exit buttons, magnetic door detection, and dip switch settings. Each interface serves a specific function related to access control operations.
System Wiring References
Refer to the user manual for detailed system wiring references to ensure proper installation and connection of the Wiegand Access Controller.
Multi-door Control Function Description
The multi-door control function allows for configuring the device for offline or TCP/IP LAN networking modes. Proper switch settings ensure the access control system operates as intended.
Multi-door Control Configuration
To configure multi-door control, add users and set permissions in the management center. Users can then access controlled areas by swiping cards, using the app, entering passwords, etc. Detailed controller management is essential for effective access control.
FAQ
- Q: What should I do if the device is not recognize access cards?
- A : If the device is not recognizing access cards, check the card capacity limit and ensure that the cards are properly programmed in the management platform.
Product Overview
Parameter:
| Input | DC12V/500MA |
|---|---|
| Working mode | networked, offline multi-mode selectable Card |
| issuing mode | management platform card issuing |
| Card capacity | 40000 |
| Password capacity | 20000 |
| Working temperature | -20℃~-70℃ |
| Relative humidity | 20%~93% |
| size | 16210538.5mm |
Controller interface description
Interface descripZon:
Interface
Name
| Function
Description
| Remarks| Interface
Name
| Function
Description
| Remarks
---|---|---|---|---|---
+12V| DV12V power
input
| | GND| groud|
12V| Wegen Readhead
Power Supply
| | ALARM| Firefighting linkage
signal
|
GND| Wegen Reading Headland| A total of 4 groups o signals for 4
redheads
| NO| Relays normally open|
Total of 4
signals for 4 locks
D1| Wegen Readhead D1| COM| Relay Common
D0| Wegen Readhead D0|
NC
| Relay normally closed terminal
LED| Indicator Synchronization signal| |
EXITx
|
Exit button signal
| Total of 4 signals for 4 gates|
DSWx
| Door magnetic detection signal| Total of 4
signals for 4 gates
---|---|---|---|---|---
GND| Go out button ground| GND| Magnetic door detection ground
SW1 dip switch: (dip code does not dial means 0, dip code dial to ON means 1)
00: TCP/IP LAN networking 01: Offline
System wiring references
Multi-door Controll Function Description
Switch Setting：
Startup status:
TCP/IP LAN networking : When the power is on, the blue LED flashes,
indicating that it is looking for the network. When normally connected to the
network, the buzzer “tick ~ tick” two short beeps, the LED red light is always
on, indicating that the cloud access control has started normally; when 20
seconds later is not normally connected to the network, the buzzer “tick tick
tick” three beeps, the LED red light is always on, indicating Connection
network failure, the controller forced to start. After the controller is
normally connected to the network, the LED green light will flash once every
20 seconds, indicating that there is data and the cloud platform interactive
communication.
Offline working: When the power is started, the buzzer “beep” a short
beep, the LED red light is always on, indicating that the cloud access control
has started normally.
Unlock status:
When the lock is opened legally, the buzzer of the controller and the reading head will be “beep” at the same time, accompanied by a green LED flashing once, and the corresponding relay will be jumped, which means that the lock is opened successfully; when the lock is opened illegally, the buzzer of the controller and the reading head will be “beep beep beep” three times at the same time, accompanied by a red LED flashing three times, which means that the lock is opened and failed.
Unlock method:
The device can be unlocked by swipe card, remote APP, out door button, management center platform remote, cloud server platform remote, password (optional), and many other ways.
Multi-door Control Configuration
Management Center Add Controller
Connect the controller to the PC with a network cable, open the controller management software, and click Add Controller by Search. At this time, the management software can automatically search for the multi–door controllers connected to the LAN and assign them to the corresponding IP. Then configure the controller to the corresponding area. Click to confirm that the controller can be bound to the corresponding regional access control.
Add the user and configure his permissions
In the management center, add users to configure the rights of thecorresponding area controllers for them. After the configuration is completed, users can open the door in the room where these controllers are installed by swipe card, APP, password, etc. More detailed controller management and
Add user：
Configuration Permissions:
Documents / Resources
|
Trudian Wiegand Access
Controller
[pdf] User Manual
Wiegand Access Controller, Access Controller, Controller
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>