Trudian TD-K1 Pro-B Smart Door Lock User Guide
- June 12, 2024
- Trudian
Table of Contents
- Accessory
- Door opening direction
- Adjust right handle and left hande
- Adjust the mortise direction
- Accessories for sorts of door thickness
- Caution before installation
- Installation
- Check points after installation
- Main function modules
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
QUICK START GUIDE
Smart Door Lock
Applicable Model: TD-K1 Pro-B
Version : 1.0
Date : JUNE 2023
Touching future
Installation instruction of anti-theft lock body
Accessory
Door opening direction
- Right handle opening
- Left handle opening
Adjust right handle and left hande
Release the screw with a screw driver, and turn 180 degree according to your
needs to adjust the left and right, fix the screw after the handle on the
correct direction.
Note: DO NOT REMOVE THE SCREW INSIDE THE HANDLE HOLD, OTHERWISE, THERE I
S NO WARRANTY.
Adjust the mortise direction
According to the your need to adjust the mortise direction.
Accessories for sorts of door thickness
Available door thickness 40mm-120mm. If the door i s over t h i s range, please contact us for more information. Please select the correct accessories according to your door thickness.
Code and name | Specifications(mm) | door thickness ranges & QTY |
---|---|---|
40-60(mm) | 60-80(mm) | 80-100(mm) |
9 Spindle (Cut the spindle according to} the door thickness) | ![Trudian TD |
K1 Pro B Smart Door Lock - mm 7](https://manuals.plus/wp-
content/uploads/2023/08/Trudian-TD-K1-Pro-B-Smart-Door-Lock-mm-7.png)| | |
13 Screw 4.2X 25 (mm)
(wood door only)| | 10| 10| 10| 10
13 Screw M5X8(mm)
(steel door only)| | 8| 8| 8| 8
8 Screw M65
(Cut the screw according to the door thickness)| | | | |
3 Fixing cylinder (Cut the fixing cylinder according to the door thickness)|
| | | |
2 Connecting pillar
40/60 (mm)| | 2| 2| |
| | | 2| 2
Caution before installation
(1) Do not be a strong force when installation , avoid to damaging the lock.|
(2) Use correct installation tools.| (3) Wear glass to protect your eyes when
drilling holes.| (4) Drilling the door holes on both side of the door
avoiding to damaging the door plate.
---|---|---|---
|
| |
Installation
Installation steps :
-
As Figure 1 :
(1) Divide the Back Lock into Battery cover and Back panel. -
As Figure 2 :
(1) Make the mortise cable get through the door plate, fix the mortise with 4 screws. -
As Figure 3:
(1) Install the two connecting pillars with two fixing cylinders onto the front panel.
-
As Figure 4 :
(1) Insert the spindle onto the mortise.
(2) Get the cable across the door plate and back bottom plate.
(3) Fix the back bottom plate and front panel with two screws. ( Note: The upper a must toward toa on the bottom plate), the two on the bottom plate must toward to the central of the spindle. -
As Figure 5:
(1) Connect the front panel cable with the connect on the back panel.
(2) Fix the back panel on to the back bottom plate with 4 screws. (Note: make sure the knob is vertical. -
As Figure 6:
(1) Put the Batteries correctly and fix the Battery cover. -
As Figure 7:
(1) Fix the strike box on the door frame, and then fix the strike plate with 4 screws on the door frame.
Check points after installation
- The face plate is horizontal with the door.
- The Latch bolt, Dead bolt and Security B o l t must works smoothly and flexibly.
- The Front lock is vertical and stable.
- Front handle works smoothly and flexibly, Dead bolt should be in position when you l i f t the handle.
- Dead bolt should be i n position when you l i f t the Back handle, and it should be retracted when you press the handle.
- Knob turns smoothly and f l e x i b l y , and Security bolt reaches out or retracts should be together with the Knob’s action.
Intelligent lock(five in one) operation manual
- Function and Operation
1.1 Description of terms and functional keys
1 ) Adminstrator information: refer t o the Administrator’s fingerprint, password or IC card.
Unlock information: refer to the input fingerprint, password ,Remote control or IC card information (including Administrator and ordinary users).
- Key“*”: clear key/back key. Enter the password or point by clearing the
previous input.Press the clear key three times i n succession, empty all
input.
3 ) Key“#”: confirmation key or menu function key.
- Original state
1 ) The factory administrator orinitial password is 123456, under the orinitial state any fingerprint, IC card or password can open the lock.
- Any fingerprint, |C card ,or password which are not registered can’t open the lock after inputting the administrator information.
-
Lock function management (step one)
-
Administrator settings
- Add administrator (step 2)
2) Delete administrator information
-
Common user setting
1)Add administrator information
2 ) Delete user information
-
system setting
1 ) Voice setting
2) Unlock mode setting
3) Language settings
4) Time setting
-
Restore factory settings
-
APP Configuration (Tuya Smart) – optional
https://smartapp.tuya.com/tuyasmart
- Search “Tuya Smart” in App Store or an App market, download and install it.
- Register with your cellphone number and log in.
- Click “Security &Sensor”, find “Lock(Wi-Fi)”, click and add a device following instructions before use.
- Remote unlocking: wake up the screen and press “9”+”#”. There will be a
voice prompt: requesting remote unlocking.
Add one network - Press“*”+“#’to authenticate administrator identity and then press “1” to
access administrator settings.
Then there w i l l be a voice prompt of pressing “3” for network configuration. - Voice prompt in network configuration mode: press “1” for hotspot
connection and “2” for intelligent connection.
3 ) When the network i s successfully added, the 1% , 2, 3 and 4″ lights on the keyboard will be on in order with a voice prompt o f “ operation completed”. - I n the event of network addition failure , the 1°’ , 2™ , 3 and 4″ lights
o n the keyboard will not b e on and there will be a voice prompt of “
operation failed” upon timeout.
Notice:
Please add administrator before setting.
- Other notes
- Input the wrong password more than 5 times in arow, the keyboard locked for 30 seconds, it does not respond to any operations in 30 seconds.
- Password peeping prevention function: input password as follows when
opening the door with password: XXX password XXX; you can add some extraneous
codes before and after the password, and then press # to confirm. The password
must be included in the input contents.
3 ) If there is no operation more than 10 seconds , system will automatically exit. - After the voltage is lower than 4.6v, the lock will automatically alarm
every time when i t is opened. After the alarm, the lock can be opened for
about 200 times.
5 ) Remove the battery cover,press the “Set” key for 6 seconds,the lock was restored to factory mode; - In factory mode, input “333666999#” cna change the language quickly;
7 ) When unlocking, input “5#’to enter passage mode(One time effective); - When unlocking, input “*”to broadcast the user number;
-
Technical Parameters
**** Technical Parameters| Items| Parameters| Memo
1| Static current| ≦ 50uA|
2| Dynamic current| ≦ 180mA|
3| Administrators number| 9|
4| Fingerprint number| 100|
5| Fingerprint + password + card capacity| 300|
6| Fingerprint Sensor| Semiconductor|
7| Fingerprint contrast time| ≦ 0.6Second|
8| Fingerprint identification Angle| 360°|
9| False Rejection Rate| 0.1%|
10| False Recognition Rate| ≦ 0.0001%|
11| Reaction time| ≦ 0.1 Second|
12| Power type| 6V|
13| Emergency power| 5VDC|
14| Working temperature| -25°C-60°C|
15| Working Relative Humidity| 20%90%RH|
16| Human voice| Yes|
17| Keyboard| Touch standard 12-bit keyboard|
18| Password Length| 4-8 digits|
19| Phantom password| 32 digits|
20| Low voltage alarm| 4.6±0.2V|
21| Unlock time| ≦ 1Second|
Smart lock manual
Main function modules
-
APP registration and login
• APP registration: if you do not have an APP account, you can choose t o register or log inby SMS verification code.
• Click “create a new account” to enter the account registration page. According to theprompt to obtain SMS verification code, setthe password.
• I f you have an existing account , click “login with an existing account” to log in to the APP. Password, verification code, and social account login are supported.
-
Create Homes
• Create your home after registering and logging in successfully.
• Each account can create and add multiple homes, and devices can be grouped by room in the home.
• Weather and other functions depend on the geographical location of the family, which is recommended to set in advance.
-
Add WiFi lock
• On the Tab of “my home”, click “+” in the upper right corner to enter the interface in figure 1 , select the WiFi door lock i n security sensor part and enter the page in figure 2 .
• When the device enters the connected mode, continue t o operate according to the instructions and APP tips.
-
Home Page
• Home page includes remote unlock, alarm message, member management, record, temporary password and other functions.
• Remote Unlock: initiate a request from the door lock , and the app can respond t o allow / refusal door opening
-
Dynamic password
-
Click t o get the dynamic password Meanwhile copy the password text for you
-
Message center
• Message center contains alarm information, doorbell call information and hijacking alarm information, which can be inquired.
-
User Management
• User can be added, deleted or changed in member management.
Only the administrator user of app is allowed to do that. -
Record Log
• 24/7 Record Log, arranged in reverse chronological order. The unlocked ID with the associated user name will directly display the user name, while the unlocked ID without the associated name will display the specific unlock ID
-
Temporary password
• Temporary password can be created and deleted through a p p . After each create o r delete is completed on the app, the lock hardware is required to synchronize with the server.
• At the time of creation, you can choose whether to send SMS or not. Worldwide SMS is supported.
-
Hijacking alarm
• When the anti-hijacking mark i n the left picture is opened, if the unlock action of the unlock ID occurs, the record will report and the app will trigger the anti-hijacking alarm
-
Factory Data Reset
• Click the icon in the upper right corner of the main interface. Find the Factory Data Reset and click.
• The Factory Data Reset can also be operated on the lock. Please refer t o the instruction manual for details.
-
www.trudian.com/en/
HQ Add: Farbell Technology Park, Yixian Road, Nanlang,
Cuiheng New District, Zhongshan City, Guangdong Province,
China. Zip Code:528451
Phone: +86 0760 – 23689666
E-mail: sales@trudian.com
I f the problem i s not solved properly,please send the mail to:
support@trudian.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>