Trudian TD-8701A Wiegand Multi Door Controller User Guide

Trudian TD-8701A Wiegand Multi Door Controller

Product Information

• Product Name: Wiegand Multi-door Controller
• Applicable Model: TD-8701A, TD-8702A, TD-8704A
• Version: 1.0
• Date: May 2023
• Working Voltage: DV12V
• Swipe Distance: 0~4CM
• Working Current: 100MA~500MA
• Card Reading Type: IC card
• Working Mode: Networked, offline multi-mode selectable
• Card Management Platform: Card issuing
• Working Temperature: -20°C to 70°C
• Card Capacity: 40000pcs
• Relative Humidity: 20% ~ 93%
• Open Mode Size:
  • Control Box: 273 232 67mm
  • Reading Head: 86 86 8MM
• Installation Method: Inside the wall, with a depth of 50MM

Product Overview

Parameter:

reading head :86 86 8MM

Installation method| Control box: hanging installation reading head : 86 box embedded installation.86 box requires a depth of 50MM inside

Controller interface description

Interface description:

Interface Name| Function Description| Remarks| Interface Name| Function Description| Remarks
---|---|---|---|---|---
+12V| DV12V power input|  | GND| ground|
12V| Wegen Readhead Power Supply|  | ALARM| Firefighting linkage signal|
GND| Wegen Reading Headland| Total of 4 groups of signals for 4 readheads| NO| Relays normally open| Total of 4 signals for 4 locks
D1| Wegen Readhead D1| COM| Relay Common
D0| Wegen Readhead D0| NC| Relay normally closed terminal
LED| Indicator synchronization signal|
EXITx| Exit button signal| Total of 4 signals for 4 gates| DSWx| Door magnetic detection signal| Total of 4 signals for 4 gates
GND| Go out button ground| GND| Magnetic door detection ground
SW1 dip switch: (dip code does not dial means 0, dip code dial to ON means 1)

00: TCP/IP LAN networking 01: Offline

System wiring references

Wiegand Reader Installation diagram

• Connect the signal line in the back of the read head device as shown in the figure below.
• Install the reading head device into the 86 box, (note that you need to use the embedded wall inside the depth of 50MM style 86 box), lock the screws to fix, as shown in the figure below.
• Read the head panel and read the head body snap together, first from the upper snap down and then press the lower and bottom screw hole alignment; finally in the bottom of the anti-theft screw hole screwed on the countersunk head machine wire within the plum security screws fixed,as shown in the figure below.

Function Description

Operating mode selection

Startup status

• TCP/IP LAN networking: When the power is on, the blue LED flashes, indicating that it is looking for the network. When normally connected to the network, the buzzer “tick ~ tick” two short beeps, the LED red light is always on, indicating that the cloud access control has started normally; when 20 seconds later is not normally connected to the network, the buzzer “tick tick tick” three beeps, the LED red light is always on, indicating Connection network failure, the controller forced to start. After the controller is normally connected to the network, the LED green light will flash once every 20 seconds, indicating that there is data and the cloud platform interactive communication.

• Offline working: When the power is started, the buzzer “beep” a short beep, the LED red light is always on, indicating that the cloud access control has started normally.

• Unlock status
  When the lock is opened legally, the buzzer of the controller and the reading head will be “beep” at the same time, accompanied by a green LED flashing once, and the corresponding relay will be jumped, which means that the lock is opened successfully; when the lock is opened illegally, the buzzer of the controller and the reading head will be “beep beep beep” three times at the same time, accompanied by a red LED flashing three times, which means that the lock is opened and failed.

• Unlock method
  The device can be unlocked by swipe card, remote APP, out door button, management center platform remote, cloud server platform remote, password (optional), and many other ways.

Configuration

Management Center Add Controller
Connect the controller to the PC with a network cable, open the controller management software, and click Add Controller by Search. At this time, the management software can automatically search for the multi-door controllers connected to the LAN and assign them to the corresponding IP. Then configure the controller to the corresponding area. Click to confirm that the controller can be bound to the corresponding regional access control.

Add user and configure his permissions
In the management center, add users to configure the rights of the corresponding area controllers for them. After the configuration is completed, users can open the door in the room where these controllers are installed by swipe card, APP, password, etc. More detailed controller management and

• Add User:
• Configuration Permissions:

Remote control controller

Remotely open doors and view access records
After you open Trudian APP and log in the user you have added in the management center, the APP home page shows all the controllers that the current user can control. You can open the door remotely in APP, and you can also view all the door opening information recorded by the controller in APP.

• View access records with APP:
• Open the door remotely with APP:

www.trudian.com/en/

HQ Add: Farbell Technology Park,Yixian Road, Nanlang, Cuiheng New District, Zhongshan City, Guangdong Province, China. Zip Code:528451
Phone: +86 0760 – 23689666
E-mail: [email protected]
If the problem is not solved properly,please send the mail to: [email protected]

References

• Home - Guangdong Trudian Technology Co., Ltd.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>