NINGBO BS60 Under Desk Charging Station Instruction Manual
- July 6, 2024
- Ningbo
Table of Contents
NINGBO BS60 Under Desk Charging Station
Product Introduction
This is an innovative high-speed mobile charging station. The package includes an optional wireless charging pad, the battery station locking frame and the 20,000 mAh battery with locking key.
The under-surface charging station combines slimness and robustness and can be easily and quickly installed underneath table tops using the screws supplied. It can charge mobile phones that support the QI standard. It is suitable for non-metallic desktops such as marble, wood, and glass.
Installation Kit
- Wireless Charging Pad ( optional )
- Battery Dock
- Battery Pack ( 1xUSB-A port +1xTypc-C port+ wireless charger)
- lnstallation Screws x4
TOOLS REQUIRED
Installation Steps
Wireless Charging Pad Installation
Before starting the installation please check that you have the minimum surface required to install the system. No more than 10cm.
A. Place a mark at 80-150mm (recommended) from the edge of the table.
B. Drill a hole (4-5mm).
This hole should penetrate the desktop, allowing the wires of the antenna to
pass through the table to connect to the battery pack.
C. Positioning the charging pad in the desired location, feeding wires
through hole and then sticking in place using the adhesive.
Bracket Installation
A. Connect the wires to the terminal block on the battery station frame.
B. Fix the table dock using 4 screws provided.
C. Please confirm everything is well connected. Insert the battery into the bracket. Press the locking button upwards to lock the battery pack.
D. Place your Qi compatible smartphone on the wireless charging pad
and/or connect your smartphone or laptop with a cable to USB or Type-C port on
the battery. Please note that some very thick phone cases (or metal phone
cases) may affect charging.
When the battery needs to be recharged, use the provided key to rotate and unlock. Please use Type-C on the battery pack for battery recharging.
Specifications
Battery capacity : 20,000mAh
Input: 5V/3A
Output: USB: 5V/3A, 9V/2A, 12V/1.5A (18W max)
Type C : 5V/3A, 9V/3A, 12V/3A,15V/3A, 20V/3A (60W max)
Wireless:5V/2A, 9V/1.67 A (15W max)
Product size: 1988855mm
Power Display
Phone Charging Display
| No. | Power | LED Display |
|---|---|---|
| 1 | 0%-100% | Green Light On |
| 2 | 2:10%-<19% | Yellow Light On |
| 3 | >0%-<9% | Red Light On |
Battery Recharging Display
| No. | Power | LED Display |
|---|---|---|
| 1 | 2:66%-100% | Green Light Flash |
| 2 | 2:36%-<66% | Yellow Light Flash |
| 3 | >0%-<33% | Red Light Flash |
Warranty
The following conditions are not covered by the warranty:
- Accessories are not covered by the warranty.
- Failures due to improper operation or installation by the user are not covered.
- Failures caused by disasters, man-made damage, self-disassembly, unpacking, and repairs by non-authorized maintenance centers of our company are not covered.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:(1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance between 20cm the radiator your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>