TONOR T20S Microphone Stand Instruction Manual

TONOR T20S Microphone Stand

Product Specifications

• Product Name: T20S Microphone Stand
• Compliance: FCC radiation exposure limits
• Minimum Distance: 20cm between radiator and body

Product Usage Instructions

1. Setup
   Place the T20S Microphone Stand on a stable surface where you intend to use it for microphone support.

2. Adjusting Height
   Loosen the height adjustment knob, adjust the height of the stand to your desired level, and then tighten the knob to secure the position.

3. Attaching Microphone
   Attach your microphone to the stand using the microphone clip or holder provided with the stand. Make sure it is securely in place.

Positioning
Position the microphone stand as needed for optimal audio capture. Ensure it is stable and not obstructing any sound sources.

Frequently Asked Questions (FAQ)
Q: Is the T20S Microphone Stand compatible with all types of microphones?
A: The T20S Microphone Stand is designed to be compatible with most standard microphones that fit within the provided microphone clip or holder.

Microphone Stand

RoHS
support@tonormic.com
www.tonommic.com

• A. 3/8″ to 5/8″ adapter
• B. USBcable
• C.Clamp

1. Install the clamp onto the table surface (0-6cm thicness) and adjust the bottom knob to secure the clamp.

2. Plug the boom arm into the base, adjust the stand to the optimal position. Then adjust the knob on clamp to fix the boom arm.
   

3. Install the 3/8″ to 5/8″ screw adapter onto the end of metal rod.

4. Install the microphone onto the metal rod through the 3/8″ to 5/8″ screw adapter.

5. Open the slots on the upper and lower arms of the stand

6. Insert the USB cable into the Type C port of the stand, connect the other end to a PC or 5V/1A charger, and the light will turn on.

7. Fix the USB cable of the microphone on the card slot, connect one end to the mic power port, and the other end to the PC. The mic can work normally.

8.  Finally, install the card slot back to its original position.

9. Final form

10. Lighting control: Scan the QR code to download the app,  or search for “Rainge!” app in the app store on Android/lOS devices to download the app. After the USB cable is plugged into the stand, the app will automatically identify and connect to the device, and the device name starts with “TONOR_”, followed by two letters or numbers.

FUJIAN EASTWEST LIFEWIT TECH NO LOGY CO.,LTD
RM 1201-1205,BLD 18,2ND PHASE OF INNOVATION PARK, NO.7,WULONGJANG MIDDLE
AVENUE, FUZHOU HIGH-TECH ZONE, FUZHOU,

FUJIAN PROVINCE

• EASTWEST ELECTRONIC COMMERCE
• CO US LIMITEDl3500 SOUTH
• DUPONT HIGHWAY, SUITE G106
• DOVER, DE 19901 UNITED STATES
• LIFEWIT LIMITED IUNIT 2, VINCENT HOUSE,
• FIRCROFT WAY, EDENBRIDGE UNITED
• KINGDOM
• Lifewit GmbHIFriedenstraBe 5 97072
• Wuerzburg Germany

Specification

• US/GB
• Model:T20S
• Material: Steel and ABS
• Weight: 1.9pound
• Max.Horizontal/Vertical Length: 700mm/690mm
• Rotation Angle: 360°
• Maximum Support Weight: 3.3lbs/1.Skg
• Maximum Support Weight at 180 Degree Angle: 2.2Ibs/lkg

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gene rates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If thi s equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

ISED Statement

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>