KSIX BTW01N Odissey Headphones User Manual
- June 28, 2024
- KSIX
Table of Contents
**KSIX BTW01N Odissey Headphones User Manual
**
Characteristics
Technical specifications
Playtime: 30 hours
Battery: 500 mAh
Frequency range: 20 Hz – 20 kHz
Protection rating: IPX4 (against sweat and rain proof)
Operation range: 10 meters
Frequency range: 2.40GHz-2.480GHz
Maximum transmitted power in frequency ranges: 3 dBm
Noise cancelling: ANC and ENC
Sensitivity: 99dB±3dB at1KhZ
Impedance: 32 15% Ω
Charging time: 3 hours
Weight: 242 g
Material: ABS
In the box
1 x Headphones
1 x USB-A to USB-C cable (38.6 cm)
1 x Headphones case
1 x Jack cable 3.5 mm (1 m)
1 x Manual
Product details
- Volume
- ON/OFF
- USB-C port
- NC button
- LED indicator
- Jack port
Headphones LED indicators
The headphones LED indicator informs about the state of the connection, among other aspects:
Pairing| A blue and red light will flash quickly until the headphones are
paired.
---|---
Connected| The flashing light will turn off
ANC/ENC modes| A green light will remain steady when you activate these modes.
Charging| A fixed red light will show when you start charging them. When the
headphones are completely charged, no light will show.
Initial setup
Turn on/off the headphones
To turn on the headphones press the multi function button for 3 seconds, you will then hear “Power on”. To turn them off, do the same; you will then hear “Power off”.
How to pair the headphones
Turn the headphones on as shown previously. When you do so, the blue and red
pairing lights will start to flash alternatively, this means that the device
is in pairing mode.
Activate the BT on your device, search for “KSIX ODISSEY” on the available BT
devices list and select it. Once the connection has been successful you will
hear a special sound. Once the headphones have been connected to a device,
they will pair with it automatically when turned on.
Troubleshooting : If the headphones do not turn on automatically, it should be due to low battery. Please, charge the headphones. If they do not pair with your device properly, reset the headphones as instructed later in this manual.
Usage method
| Play/Pause | Tap power switch once to play or pause the music. |
|---|---|
| Volume -1+ | To decrease the volume, tap once the volume down button. To |
increase the volume, tap once the volume up button.
Previous/Next song| To play the previous song, 2seconds long press
the volume down button once.To play the next song, 2 seconds long press the
volume up button once.
Answer/Hang up calls| To answer an Incoming call,press the
power button once.To hang up, press the power button once.
Reject calls| To reject an incoming call, long press the power button for 2
seconds.
Call last number called| Quick tap twice power button to redial last number.
NC button| Tap NC button once to activate ANC on or off.
How to reset the headphones **
**
To reset the headphones, disconnect them, access your device’s BT settings, tap on “KSIX ODISSEY” and then on unpair. Turn them on again and repeat the pairing process.
There is another way to reset the headphones. When the headphone is disconnected, press the multi-function button 6 times to reset the headphone. After the reset, the headphone shuts off automatically.
Charging the headphones
These headphones incorporate a USB-C port. Connect the cable that is included
in the package or a compatible cable to a wall charger, powerbank or computer
output.
It takes about 3 hours to charge the headphones up to full.
Troubleshooting: If the headphones LED indicator does not turn on during its
charge, it should be due to a power supply issue. Please, check if the
charging cable is correctly connected to the charging case. Check both ends of
the cable, as well as the power supply state and the device you are using to
charge, whether it is a wall charger, a powerbank or a PC port.
Safety, maintenance and usage recommendations
Read all documentation and instructions provided before using the product. Use only accessories compatible with the product. Clean the product regularly with a dry cloth. The product must be unplugged or switched off when cleaning. Keep the product’s ports and connectors clean from dust, dirt, etc., to ensure proper connection. Avoid breaking the product. Do not apply excessive pressure to any part of the product. If the product has a cable, do not bend it and do not pull it with excessive force to avoid damaging it. Do not expose the product to a higher level of humidity than it was designed for. If the product is resistant to liquids, after any immersion or use in liquids, rinse the product with fresh water and dry it. Always keep the product in a dry place away from moisture. Always keep the product away from flammable materials and do not expose it to fire, heat sources or extreme temperatures. When the product is not in use, unplug it and store it in a clean, dry place away from moisture and dirt. If water enters the product, immediately disconnect it from any power source or device to which it is connected. Do not use the product for any purpose other than that for which it was designed. Do not use the product if you notice any visible defects. Do not open or disassemble the product or attempt to repair it yourself. These actions invalidate the warranty. Keep the product out of the reach of children. Recycle the product in accordance with local environmental rules and regulations. If the product includes a battery, maintain the state of charge between 20% and 80% of its capacity to preserve the battery life.
Legal Note
Atlantis Internacional, S.L, declares that this product is in compliance with
the essential requirements and any other applicable or enforceable provisions
of Directive 2014/53/EC.
The functions and characteristics described in this manual are based on tests
carried out by Atlantis Internacional S.L.
The user is responsible for examining and verifying the product when
purchasing it. Atlantis Internacional S.L. declines all responsibility for any
personal, material, economic damage, as well as any damage to your device, due
to misuse, abuse or improper installation of the product.
Disposal of electrical and electronic equipment
The CE symbol indicates that electrical and electronic equipment must be disposed of separately. This product is designed to be disposed of separately at an appropriate waste collection point. Do not dispose of it with household waste. If the equipment is battery operated, the batteries must be removed and disposed of at a separate collection point for this type of waste. If the batteries are not removable, do not attempt to remove them, as this must be done by a qualified professional. Separate disposal and recycling helps to conserve natural resources and prevent harmful consequences to human health and the environment that could arise from improper disposal. The final price of this product includes the cost of the environmental management necessary for the correct treatment of the waste generated. For more information, please contact the seller or your local waste management authority.
CE Declaration of Conformity
We hereby declare that the product (s) listed below satisfies the provision for CE-marking, , complies with Directive 2014/53/EU and may be sold in all EU countries, according to the following European directive(s):
ETSI EN 301 489-1 V2.2.3 (2019-11)
Draft ETSI EN 301 489-17 V3.2.6 (2023-06)
EN 55032 : 2015/A1:2020
EN 55035 : 2017/A11:2020
ETSI EN 300 328 V2.2.2 (2019-07)
EN 62479 : 2010
EN 50663 : 2017
EN IEC 62368-1: 2020+A11:2020
Article : B T W 01 N
EAN: 8427542134550
Manufacturer: ATLANTIS INTERNACIONAL, S.L.
Address: Barcelona (Spain)
Nico Broder General Manager
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>