VITEK TNT8FADW-2 Fixed Turret Camera User Guide

VITEK TNT8FADW-2 Fixed Turret Camera

USER GUIDE

VTC-TNT8FADW-2
Transcendent Knight Guard Active Deterrence 8MP (4K) Advanced A.I. Fixed Turret Camera

FEATURES:

• 1/1.8” 8.0 MegaPixel (4K) CMOS Image Sensor
• Full Color at Night Camera with Active Deterrence
• Up to 30fps @ 8MP (3840 × 2160)
• 2.8mm Fixed Iris Lens
• White Light + Matrix IR (130’ Range)
• GEN IV Advanced Analytics including Face Detection
• Integrated Audio + Speaker*
• MicroSD Card Slot (256GB)
• IP66 Weather Resistance
• 12VDC + PoE Operation
• 3-Year Warranty

*Please research local, state and federal laws regarding the implementation of audio surveillance.

PLEASE NOTE:
Complete User Guide, Software, Tools, and Updates are available online. Scan the QR Code or visit:
http://www.vitekcctv.com/Downloads

Components and Accessories

Overview

1. Ethernet Connector
2. Audio Input Connector
3. Audio Output Connector
4. Alarm Input / Output
5. Power Connector
6. Speaker
7. Mic
8. MicroSD Card Slot
9. Reset

First connect the Weather Resistant Cap to an Ethernet patch cable, then connect the camera’s ethernet adaptor. If not powering the camera with PoE, also connect the power Cable to an approved 12VDC Power Supply.

Connecting Alarm Input / Output

Installation

Before beginning installation, make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. The mounting steps are as follows:

First Install a MicroSD Card as Demonstrated in Diagram at Right

1. Attach the drill template to the place where you want to install the camera, then drill 3 screw holes and 1 cable hole (if you want to route the cables through the mounting base) according to the drill template (see below).

2. Route and connect relevant cables.

3. Attach the mounting base to the wall with the provided screws.

4. Loosen the fixed ring to adjust the viewing angle of the camera. Preview the camera’s image on a monitor.

5. Tighten the lock screw to finish the installation.

LAN Configuration

The camera can be accessed on the local network either using the IP-Tool or directly in a web browser.

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.
2. Locate the IP-Tool installer at www.vitekcctv.com/Downloads/Soft-ware /Transcendent-IPTool.zip, then install on the PC. Open the installed application.

3. Modify the IP address. The default IP address is 192.168.226.201. Click the information of the camera listed in the above table to show the network information on the right side. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as the computer’s. Please modify the IP address of your device according to the practical situation.

For example, the IP address of your computer is 192.168.13.4. So the IP address of the camera should be changed to 192.168.13.X. After modifying, please input the password of the administrator and click “Modify” button to modify the setting.

** Default admin password: “123456″.

4. Double-click the IP address and then the system will pop up the web browser to connect IP-CAM. Edge in IE mode / IE browser will download the Active X. control. After downloading, a login window will pop up as shown below:

Input the user name and password to log in.
Default user name: admin / Default password: 123456.
Directly Access Through a Web Browser
The default network settings are as shown below:
IP address: 192.168.226.201 HTTP: 80
Subnet Mask: 255.255.255.0 Data Port: 9008
Gateway: 192.168.226.1

You may use the above default settings when you log in the camera for the first time.

1. Manually set the IP address of the PC. The network segment should be the same as the default settings of IP-CAM. Open the network and share center. Click “Local Area Connection” to pop up the following window.

Select “Properties” and then select Internet protocol according to the actual situation (for example: IPV4). Next, click “Properties” button to set the network of the PC.

2. Open Edge in IE mode / IE browser and input the default address of IP-CAM and confirm. Edge in IE mode / IE browser will download an Active X control.
3. After downloading the Active X control, the login dialog box will appear.
4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the LAN; Then log into the menu to set up the port number.
4. Open the web browser and input its WAN IP and HTTP port to access the IP- CAM.
3. Go to the router’s management interface through IE browser to forward the IP address and port of IP-CAM in the “Virtual Server”.
camera via LAN and go to System Congfig—+Network Config—+Port
2. Enter System Config—+Network Config—+IP Address menu to modify the IP address.

3. Go to the router’s management interface through IE browser to forward the IP address and port of IP-CAM in the “Virtual Server”.

4. Open the web browser and input its WAN IP and HTTP port to access the IP- CAM.

How to Set Up Audio / Light Alert on Event

1. Log into camera. Default username is admin and password is 123456.

2. Click on Config Tab.

3. Under Event click on event that will trigger audio and / or light. Line crossing as an example.

4. Enable line crossing. Also enable “Trigger Audio Alarm”, and also “Trigger Light Alarm”, and then click “Save” at bottom of screen.

5. Click on “Area” at top and then click on “Draw Area”, then left click and hold to draw the line. After the line is in the image, select which direction trips the event, A>B, A<B, then click “Save”.