OTTERBOX 3k mAh Wireless Power Bank for Magsafe Instruction Manual

3k mAh Wireless Power Bank for Magsafe
Instruction Manual

USE INSTRUCTIONS
More product information
otterbox.com/support
otterbox.com/accessories/magsafe

3k mAh Wireless Power Bank for Magsafe

SETUP
Fully charge Power Bank before first use with included cable.
While charging display continually shows:

• 1 flashing LED – < 25% capacity
• 1 solid LED, 1 flashing LED – 25-50% capacity
• 2 solid LEDs, 1 flashing LED – 50-75% capacity
• 3 solid LEDs, 1 flashing LED – 75-99% capacity
• 4 solid LEDs – 100% capacity

When not charging, press button to view capacity:

• No LEDs – 0% capacity
• 1 flashing LED – 0-10% capacity
• 1 solid LED – 10-25% capacity
• 2 solid LEDs – 25-50% capacity
• 3 solid LEDs – 50-75% capacity
• 4 solid LEDs – 75-100% capacity

WIRELESS CHARGING

1. Attach Power Bank to MagSafe-compatible iPhones and cases
2. Press button at bottom to turn on Power Bank
3. Charge indicator appears in upper right corner of iPhone (standard function), and first Power Bank LED displays green during charging
4. Power Bank auto-stops charging when phone is full
5. To manually stop charging, press and hold button

DUAL-DIRECTION CABLE CHARGING

Charge a device with Power Bank via a USB-C cable.

Recharge Power Bank with USB-C cable and a charger.

REMOVE POWER BANK

Remove Power Bank from phone with one hand using a twist motion from the bottom.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Project Name: INSERT INSTALL LILFINGER 3K WIRELESS POWER BANK
Part #: 20-56374
Rev: A
Date: 8.22.21
Colors Coatings and Treatments:

| Process Black
---|---
| PMS-Cool Gray 7 C

NOT FOR PRINT – FOR REFERENCE ONLY

| Dielines do not print
---|---
| Folds do not print

Designer: Rowell
Dieline and material shall follow: 23-83704
Notes:

Confidential property of Otter Products LLC
Reproduction and unauthorized use is prohibited
Otterproducts LLC: 209 South Meldrum Street,  Fort Collins,CO 80521

Industry Canada Statement

This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this  device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement
The product comply with the IC RF Exposure for Low Power Consumer Wireless Power Transfer.
RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure that compliance was  demonstrated at 20cm and greater separation from the user body or set the device to lower output power if such function is available.

Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this  device must accept any interference received, including interference that may cause undesired operation.

If device include 15B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and  used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a  particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement
The product comply with the FCC/IC RF Exposure for Low Power Consumer Wireless Power Transfer. RF exposure limit set forth for an uncontrolled environment and are  safe for intended operation as described in this manual. The further RF exposure that compliance was demonstrated at 20cm and greater separation from the user body  or set the device to lower output power if such function is available.

References

• MagSafe compatible iPhone 12 cases — designed for Apple
• Customer Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>