SILVERBACK Mercedes X Class Dual Cab Instructions
- June 7, 2024
- SILVERBACK
Table of Contents
SILVERBACK Mercedes X Class Dual Cab
IMPORTANT
|
- Do not stand/sit or rest heavy objects on Tonneau Cover
- Humans or animals are not to be under the closed Tonneau at any given time
- Securely lock tonneau Cover before operating vehicle
- Tonneau Cover is not dust or water tight
- Do not carry open volatile chemicals with Tonneau Cover installed
- If contact with volatile chemicals occur, clean Tonneau with mild detergent and water solution
---|---
Care Instructions
|
- Read Instructions fully before commencing installation.
- Clean Tonneau Cover with a mild detergent and water solution
- Do not use abrasive cleaners or solvents
- Refer to manufactures instructions applicable to power drill.
- Protect Tub floor against scratches during installation process.
Maintenance
| If lubrication of the locks or hinges is required use only Graphite Powder. DO NOT use any other lubricants or oils.
Tools Required
|
- Pen / Marker
- Die Grinder & multi tool
- Soapy water solution
- Centre Punch
- Masking Tape
- Allen Key set (Metric)
- Drill & Drill bits
- Scissors & Knife
- Phillips’s head screwdriver
- Ruler • Caulking Gun
- Spanner & Socket
- Silicon – Non-Acetic
- Tape measure
PARTS CHECK SHEET
PARTS IN MAIN CARTON
PARTS IN FITTING KIT
LID NUTS AND BOLTS
OTHER
ASSEMBLY
Thoroughly clean installation areas.
Important: Instructions are for Utes with an UNDER-RAIL tubliner. If you have an OVER-RAIL tubliner you must trim the top off.
Hinge mounts:
Align the hinge mounts along the front of the tray, ensuring the hinges are properly positioned from centre of tub 560 mm to centre of hinge mount either side along the inside of the front of the tub. Attach the hinges using self drilling screws (supplied) through holes pre-drilled into the hinges. Apply clear or black silicone to any gaps and between the hinges and the vehicle to prevent water entry
Measure and mark the positions as indicated above from the centre of the bed
for placement of the bottom hinges.
WARNING: RECHECK DIMENSIONS TO ENSURE CORRECT MEASUREMENT
Using a 3.5MM drill bit, drill through the holes in the top and the base of the hinge plate into the tub. Remove hinge and clean any swarf, apply Cold Galvanizing compound to the holes drilled. Using the self-tapping screws fasten the hinge into the tub
Gas Struts:
Measure from the front rail inside of the tub, measure along the top edge of
tray 760 mm (windscreen end) then down 20mm and mark the position of the
screws for the gas strut bracket. Position the gas strut bracket accordingly,
mark two mounting holes and center. Refer to Fig. 1 and Fig. 2
Using a 2 mm diameter drill bit set to 5 mm drill stop. Drill two pilot holes. Attach small gas strut bracket using self-drilling screws provided. Repeat process on other side of tray. Refer to Fig. 2 and Fig.3
Attach small shaft end of gas strut onto gas strut brackets, by clicking them in place. Refer to Fig.4 with regard to gas strut orientation.
Important:
DO NOT over tighten screws. Recommended tightening torque is 1- 3 Nm
Clean header rail (where extrusion will sit) with alcohol wipes provided and wipe away the residue with a dry clean cloth. Place the extrusion tape seal along the top of the header rail with the sealing lip facing towards the tailgate. Start the extrusion at the edge of the side rail. IMPORTANT: Position extrusion as close to the header rail rear radius. Rub down firmly to ensure maximum adhesion.
Important:
Ensure tongues are fully inserted into the hinge slots with hinge pin
securely in place.
With the Hard Tonneau Cover opened, attach the cylinder end of each gas strut onto the mounting brackets attached to the Hard Tonneau Cover by clicking into place
Use an Allen key to loosen the hex key screw on the catch and tension cable so
it is tight but doesn’t move the catch at all, then re-tighten the hex key
screw.
With the lid in closed position, lift the tailgate .
The tailgate must close gently against the silverback lid’s seal.
If you find the tailgate is hard to close, put the tailgate down and adjust
the U bolt up until the desired closing of tailgate is achieved.
NOTE: the seal must touch and compress gently to achieve sealing.
HOW TO OPERATE YOUR SILVERBACK LID
Now gently pull on the yellow release cable, so the rotery latch releases.
Aid the lid up, the gas springs will take over and it will lift it all the
way.
REMOVAL OF TONNEAU COVER
-
Open tonneau cover, Detach gas strut (1) by inserting a small screwdriver and adjusting the spring clip (2) on g as strut (1). Refer to figure 2.
NOTE: Do not remove the spring clip. only a small amount of levering is required to detach.
NOTE: 2 people are required to lift and remove the tonneau cover from the vehicle. -
Remove hinge pins (1) and remove tonneau cover (2). Refer figure 3.
REPLACEMENT OF TONNEAU COVER
NOTE: 2 people are required to lift and remove the tonneau cover from the vehicle.
-
Fit tonneau cover (2) and secure hinges with hinge pins (1).
Refer to figure 5.
-
Attach gas struts (2) by clipping into palace. Ensure narrow end (1) mounts to the vehicle.
Refer to figure 6.
Paint care instructions:
Your new painted Hard Tonneau Cover has been covered with a plastic film to protect the paint from damage. It will require cleaning and possibly light polishing after the protective film has been removed. Use polish as per new paint on a new vehicle. Wash Hard Tonneau Cover using water and normal carwash detergent and polish with an automotive polish
NOTE: Please ensure Lid is kept locked at all times when not being used, for both safety and longevity.
MX100 SILVERBACK Mercedes X Class Dual Cab 2017+
Documents / Resources
|
SILVERBACK Mercedes X Class Dual
Cab
[pdf] Instructions
Mercedes X Class Dual Cab, H100 MX100
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>