MokerLink WB900 Wireless Outdoor Bridge Installation Guide

June 6, 2024
MokerLink

MokerLink - logo Wireless Outdoor Bridge
Quickly Installation Guide

Device Installation

(Take the 5.8g wireless bridge as an example)

Working Environment:

Only applicable to areas below 2000 meters above sea level
Only applicable to areas to non-tropical weather conditions

Connection Topology

Point to Point:

MokerLink WB900 Wireless Outdoor Bridge - Connection
Topylogy IP Camera – Switch – Wireless Bridge
Wireless Bridge – DVR – Monitoring PC

Point to multiple points:

MokerLink WB900 Wireless Outdoor Bridge - IP Camera
IP Camera – Wireless Bridge
Wireless Bridge – DVR – Monitoring PC

Bridge Ways

( *Two bridge ways: One Key Bridge & LED Display Bridge)
Quick Installation Guide

One Key Bridge

1. Config Master/Slave CPE
Put the switch to H, CPE will work as Master. Put the switch to C, CPE will work as Slave.

MokerLink WB900 Wireless Outdoor Bridge - switch

*Note: The pictures of the above products may change slightly according to the production cycle, and the final appearance is based on the physical object.

2. Point to Point Connection
Press the reset button on both master and slave CPE, will start bridging.
Point to Mult Point Connection:
Press reset button on master and mult slave CPE, will start bridging.
Note: Mater CPE and slave CPE bridging actions (press reset button) need to be finished in 1 minute.

LED Display Bridge

  1. Config Master CPE
    When bridge two CPEs, make one work as master: press “F” to make H/C blinking, and press “S” to change to “H”, it will save automatically in 5 seconds

  2. Config Slave CPE
    Set another CPE to work as a slave: press “F” to make H/C blink, and press “S” to change to “C”, it will save automatically in 5 seconds.

Note:

  1. CPE default working mode is AP mode after reset, IP is 192.168.188.253
  2. F is a select button, can be used to choose master/slave working mode, wifi channel, IP, and checking signal strength.
  3. S is a config button, can be used to set master/slave working mode, wifi channel, IP.MokerLink WB900 Wireless Outdoor Bridge - Config Slave CPE

Point to Point Connection

Press the reset button on both master and slave CPE, will start bridging.

Point to muit Point Connection:
Press reset button on master and mult slave CPE, will start bridging.

Note: Master CPE and slave CPE bridging actions (Press reset button) need to be finished in 1 minute,

MokerLink WB900 Wireless Outdoor Bridge - Point to muit Point
Connection

4. Change Wifi channel

To avoid signal interference, need to change the master CPE wife channel only, slave CPE will reboot and bridge to master CPE automatically. Press F twice, change the channel by pressing S, CPE will save and reboot automatically in 5 seconds.

MokerLink WB900 Wireless Outdoor Bridge - Chang wifi
channel

5. Change IP
To avoid CPE IP conflicts, need to change the CPE IP address. Press F three times until the IP is blinking, press S to change IP, CPE will save and reboot automatically in 5 seconds.

MokerLink WB900 Wireless Outdoor Bridge - Chang ip

Web configuration

  1. PC configuration if PC connect CPE by wireless
    Set PC wireless network IP to 192.168.188.x (x: 2–250), same network segment as CPE, subnet mask: 255.255.255.0: clk After IP address configuration, connect to CPE’s wireless SSID: Wireless 5.8G, and input password (Default Password: 66666666)

  2. Login Web Configuration
    Use IE browser to access http://192.168.188.253, pop up the login page shown below, input the login password: admin, enter into the home page

  3. Bridge Status
    MokerLink WB900 Wireless Outdoor Bridge - Bridge
Status
    Login CPE (work as a repeater), will see signal strength, green is normal, between -70dBm to -40dBm.

  4. Login WEB by Mobile Phone
    Outdoor CPE supports mobile phone and set, the configure page showed as follow:
    MokerLink WB900 Wireless Outdoor Bridge - Mobile PhoneSteps:
    1. Mobile phone connect with outdoor CPE, SSID: Wireless5G, password: 66666666, or please refer to product sticker for SSID, password.
    2. Configure static IP
    Open settings in the phone, turn on WLAN and find the SSID of the CPE, touch it for a long time until there is a menu, then choose”static IP” in the menu, set the mobile phone IP address as 192.168.188.X (X can not be 253 or 252), same network segment as CPE, subnet mask: 255.255.255.0, then gateway, subnet mask, and domain.
    Open settings and choose Wi-Fi, connect with CPE, click exclamation mark®, manual to set IP address 192.168.188.X (X can not be 253 or 252) and subnet for mobile phone, note: mobile phone’s IP address should be same network segment as CPE.
    3. Input 192.168.188.253 on the internet explorer bar, input admin to log in to the mobile configuration page.
    MokerLink WB900 Wireless Outdoor Bridge - Mobile
Phone2

  5. Channel Table

Regional Code

|

SG Channel

---|---
| 5.180GHz| (Channel 36)
| 5.200GHz| (Channel 40)
| 5.220GHz| (Channel 44)
| 5.240GHz| (Channel 48)
China| 5.260GHz| (Channel 52)
5.280GHz| (Channel 56)
5.300GHz| (Channel 60)
5.320GHz| (Channel  64)
5.745GHz| (Channe1149)
5.765GHz| (Channe1153)
5.785GHz| (Channel 157)
5.805GHz| (Channe1161)
5.825GHz| (Channe1165)
America| 5.180GHz| (Channel  36)
5.200GHz| (Channel  40)
5.220GHz| (Channel 44)
5.240GHz| (Channel 48)
5.260GHz| (Channel 52)
5.280GHz| (Channel 56)
5.300GHz| (Channel 60)
5.320GHz| (Channel 64)
5.500GHz| (Channe1100)
(Channe1104)
(Channel 108)
5.520GHz
5.540GHz
5.560GHz| (Channe1112) (Channe1116) (Channe1120) (Channel 124)
5.580GHz
5.600GHz
5.620GHz
5.640GHz| (Channel 128)
5.660GHz| (Channe1132)
5.680GHz| (Channe1136)
5.700GHz| (Channe1140)
5.745GHz| (Channel 149)
5.765GHz| (Channel 153)
5.785GHz| (Channe1157)
5.805GHz| (Channe1161)
5.825GHz| (Channe1165)

Regional Code

|

SG Channel

---|---
| 5.180GHz| (Channel 36)
| 5.200GHz| (Channel  40)
| 5.220GHz| (Channel 44)
| 5.240GHz| (Channel 48)
ETSI| 5.260GHz| (Channel 52)
5.280GHz| (Channel 56)
5.300GHz| (Channel 60)
5.320GHz| (Channel 64)
5.500GHz| (Channel 100)
5.520GHz| (Channel 104)
5.540GHz| (Channel 108)
5.560GHz| (Channel 112)
5.580GHz| (Channel 116)
5.600GHz| (Channel 120)
5.620GHz| (Channel 124)
5.640GHz| (Channel 128)
5.660GHz| (Channel 132)
5.680GHz| (Channel 136)
5.700GHz| (Channel 140)

Regional Code

|

2.4G Channel

China| 2.412GHz| (Channel 1)
2.417GHz| (Channel 2)
2.422GHz| (Channel 3)
2.427GHz| (Channel 4)
2.432GHz| (Channel 5)
2.437GHz| (Channel 6)
2.442GHz| (Channel 7)
2.447GHz| (Channel 8)
2.452GHz| (Channel 9)
2.457GHz| (Channel 10)
2.462GHz| (Channel 11)
2.467GHz| (Channel 12)
2.472GHz| (Channel 13)
America| 2.412GHz| (Channel 1)
2.417GHz| (Channel 2)
2.422GHz| (Channel 3)
2.427GHz| (Channel  4)
2.432GHz| (Channel 5)
2.437GHz| (Channel     6)
2.442GHz| (Channel     7)
2.447GHz| (Channel     8)
2.452GHz| (Channel     9)
2.457GHz| (Channel 10)
2.462GHz| (Channel 11)

Troubleshooting

Trouble

| Reason|

Solution

---|---|---
Packet Latency| 1. Wireless Interference
2. Distance is too long, or there are some bar between them
3. CPE’s angle in the wrong direction, weak signal| 1. Use Wi-Fi analysis to choose the best channel or change to 5G CPE
2. CPE should be in the normal distance, and avoid bar
3. Adjust the angle of CPE according to signal strength
Wrong password| 1. Forget password
2. Input wrong password
3. Too much cookie| 1. Press the reset button in 10 seconds to reset the device, the default password is admin
2. Re-input the password
3. Clear cookie, run arp -d to clear MAC table.
Can not log in WEB| 1. Local IP is not in the same network segment of CPE
2. IP is taken by other devices
3. LAN Connection or Ethernet cable has a problem
4. Too much cookie, MAC address haven’t update| 1. Ping 192.168.188.253 to see the connection status
2. Stop other devices or change to another IP
3. Check LAN Connection and Ethernet cable
4. Clear cookie, run arp -d to clear MAC address
System LED light off| 1. PoE power supply is not working
2. Some problem in CPE’s PoE port
3. Ethernet cable is loose, RJ45 port is wrong Power current/voltage lower or wrong| 1. Check if POE Adapter or POE switch work
2. Check if the POE port of CPE is OK
3. Check if Ethernet cable is loose if Ethernet cable plugged into POE port
4. Check if the voltage is normal if the socket has a problem if the input voltage of the POE adapter is normal
Low transmission Rate| 1. Packet Latency
2. Ethernet cable circuit
3. Network virus attack
4. Too much access users| 1. Adjust the distance, angle, and channel to decrease latency
2. Check if there is a circuit in the network
3. Check if port isolated to avoid network virus and broadcast storm
4. Decrease the access users.
Device always dead| 1. Static electricity
2. Running time too long
3. Lightning stroke| 1. Make CPE or POE adapter need a ground connection
2. Running time over 7 days, reboot it
3. After lightning, device POE port is broken or unstable, better to deploy lightning conductor.

Wuhan MokerLink Technology Co., Ltd
Rm10,13/F,Main Building 7,Changhang Lanjing International,
No.116 Gaoxin Ave.,Hongshan Dist.,Wuhan,China
http://www.mokerlink.com
support@mokerlink.com

MokerLink WB900 Wireless Outdoor Bridge - qr codeFor technical support and other information, please visit
http://www.mokerlink.com/support/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals