BORMANN BBC1500 1200A Car Battery Starter Instruction Manual

BORMANN BBC1500 1200A Car Battery Starter

Specifications

• Model: BBC1500 073833
• Capacity: Not specified
• Input: USB1, TYPE-C
• Output: USB2, Air Pump Output
• Protections: Overcharge & Over-discharge Protection, Fuse
  Protection, Anti-reverse Plug

Product Usage Instructions

Safety Instructions

• Read the manual carefully before use to avoid tool damage, physical injury, and property damage. Store the manual for future reference.

Product Layout

• The product layout includes various components such as a Jumpstart Port, Hose Socket, LED Light, USB Outputs, Display, and Buttons.

Operation Guidance

• To check the storage level of the jump starter, press the Power Button. The Display shows the remaining power and activated output ports. Different numbers indicate different storage levels.

Jump Starter Charging

1. Plug the Charging Cable into electronic devices with USB output.
2. Connect the input port of the jump starter to the charge.
3. Alternatively, plug the car adaptor into the cigarette lighter socket and connect the input port of the jump starter to the car adaptor.

Starting a Vehicle

1. Ensure the remaining power is not less than 80%.
2. Connect the starter cable to the starter socket.
3. Connect the RED clamp to the positive terminal and the BLACK clamp to the negative terminal of the vehicle battery.
4. Start the vehicle with intervals of more than 30 seconds between each start.
5. After 3 failed starts, stop trying and check for engine or vehicle circuitry problems.
6. When the vehicle starts, remove the cable and disconnect the clamps from the battery terminals within 30 seconds.

FAQ

Q: Can I charge the jump starter unit immediately after starting the engines?

A: No, it is recommended to wait at least 30 minutes before charging the jump starter unit after starting the engines.

Q: What should I do if there are problems with starting the vehicle?

A: If issues are starting the vehicle, stop trying after 3 failed attempts. Check for engine or vehicle circuitry problems and verify if there is an issue with the starter itself.

SAFETY INSTRUCTIONS

• Warning: Read the manual carefully before use.
• Failure to follow the warnings and instructions may result in tool damage, physical injury, and/or property damage.
• Store the manual in a safe place for future reference.

Product layout

1. Jumpstart Port
2. Hose Socket
3. LED Light
4. USB1 Output
5. TYPE-C Input
6. USB2 Output
7. Display
8. Button
9. Pump Button
10. Power Button
11. + Button
12. Unit Button

TECHNICAL SPECIFICATIONS

Technical data

Model:| BBC1500
Capacity:| 12000 mAh
Input:| QC 18 W (5V 2A/9V 2A)
Output:| USB 1: 5 V/2.4 A

USB 2: QC3.0

Charging time:| 3-6 Hrs
Start current:| 600A
Peak current:| 1200A
Air Pump Output:| 0-120 psi
Dimensions:| 255x100x50 mm
Weight:| 850 gr
Operation temp:| -20°C ~ 60°C
Lifetime:| 1000 cycles
Protections:| short circuit proof, overcharge protection
Other features:| Led Light

• The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products.
• The parts described/illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
• To ensure the safety and reliability of the product and the warranty validity, all repair, inspection, or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
• Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death.
• The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.

OPERATION GUIDANCE

LED Display

• Press the Power Button to check the storage level of the jump starter. On the Display, it shows the remaining power and activated output ports.
• The different number displayed on Display shows different storage levels of the jump starters. The number will reach to 100%
• when the charging is complete.

Jump starter charging instruction:

1. Plug the Charging Cable into electronic devices with USB output.
2. Connect the input port of the jump starter to the charge.

Or

1. Plug the car adaptor into the socket of the cigarette lighter.
2. Connect the input port of the jump starter to the other end of the car adaptor.

Note: Do not charge the jump starter unit immediately after starting the engines, but at least 30 minutes later.

1. Make sure the remaining power is not less than 80%, full charge is recommended.
2. Connect the starter cable to the starter socket.
3. Connect the RED clamp to the positive (+) terminal of the vehicle battery and connect the BLACK clamp to the negative (-) terminal of the vehicle battery.
4. Start the vehicle. The interval between each start must be MORE than 30 seconds. After 3 failed starts, stop trying. Check for problems in the engine or vehicle circuitry. In the meantime, check if there is a problem with the starter.
5. When the vehicle starts, remove the cable from the starter and disconnect the red and black clamps from the vehicle battery terminals within 30 seconds.
6. Leave the vehicle engine running.

Smart cable instructions

1. Connect the smart cable to the jump starter unit, if the “start” and error indicators alternately flash with “green” and “red” lights, it proves the circuit normally only red light on, it proves the voltage of the jump starter is too low to start the vehicle.Correctly connect the smart cable to vehicles’ battery terminals; positive(+) to positive (+), negative (-) to negative (-)
2. The smart cable will detect the circuit for 3″ if the “start” indicator turns green and the “fault” indicator goes out, then the vehicle can be started (the green light will light for 30″, if it does not start within 30″, the smart cable will automatically turn off and the green and red lights will light at the same time. If you want to restart the vehicle, you will need to remove the smart cable from the starter and reconnect it).

– Recharge the product

2. Over-heating protection

– Remove the clamps to let it cool

3. Timeout protection

-Connection timed out. Remove the clip within 30s after a successful start

Solid red with discontinuous beeping| Reverse polarity protection

-Reverse the clips and ensure the correct connection

Solid red with continuous beeping| Short circuit protection

-Do not connect the clips or to the same metal

Charging cell phone or othe electronic device instructions

1. Plug the charging cable into the USB1 or USB2 output port.
2. Select the appropriate connector for your cell phone or other electronic device.
3. Press the Power Button to charge.

Air compressor for tire inflation

1. Connect the ends of the hose to the “Hose Socket” of the tire and the starter.
2. Turn on the Power Button, and press the Pump Button to switch to pumping mode, the default value is 2.5 Bar, press the “+” and “-” buttons to set different pressure values. Press the unit button to change the unit.
3. After the setting is complete, the air pump will start to inflate by briefly pressing the power button and the current air pressure will be displayed.
4. When the air pressure reaches the set value, the air pump will automatically stop running.

Tip: If you are using it for a long time, it is recommended to stop every 10 minutes to cool it down. Otherwise, the protection program will start automatically.

Led lamp

• Press the Power Button for 3 seconds to light the LED.
• There are 3 functions for the LED that appear in order (illumination, strobe, SOS ) if you press lightly.

Other display indicators

• H8: The battery temperature has exceeded 60°C, and the product stops working at this time. It can be used normally after the temperature returns to normal after cooling.
• H0: If the battery temperature is lower than -20°C, the product stops working. It can be used normally only after the temperature returns to the normal level.
• HH8: The temperature of the air compressor motor reaches 95°C, but the product stops working. The motor can be used normally after the motor temperature returns below 60°C (approximately 30 minutes).
• H–: The motor has reached the maximum single run time of 15 minutes and the product stops operating on site. It is recommended to cool down for at least 30 minutes before using the secondary air pump function.

FAQ

How do I turn off the device?

The device will automatically turn off when there is no charge or when charging is complete.

How many times can this device charge my mobile phone?

4 times for iPhone mobile phone.

How long will it take the device to fully charge my mobile phone?

About 1 hour.

How many times can this device with a full charge start the vehicle?

About 30 times.

How long will the battery power of the device last?

3-6 months, however, we recommend recharging it every 3 months.

Troubleshooting

recharging to activate it.

Toxic and harmful substances

Composition and quantity of toxic and hazardous substances in the jump starter

0: Indicates that the content of hazardous substances in all homogeneous materials is below the MCV limit specified in the 2011/65/EU (RoHS) standard with amendment (EU) 2015/863.

WARNING

1. Remove the jump starter unit from the vehicle within 30s.
2. DO NOT connect the two clamps. Danger may occur!
3. DO NOT disassemble the product. Danger may occur!

SAFETY INSTRUCTIONS

• This device is not intended for unsupervised use by young or infirm persons.
• Do not use it as a toy.
• Do not allow the appliance to get wet.
• Do not immerse the appliance in water.
• Do not use the appliance in explosive atmospheres such as in the presence of flammable liquids, gases, or dust.
• Do not modify or disassemble the starter. Only a qualified technician can repair this device.
• Do not expose the device to heat.
• Do not store in areas where the temperature may exceed 70â “ƒ. Charge only at ambient temperatures between 0°C – 60°C.
• Charge only with the charger supplied with the device.
• Under extreme conditions, battery leakage may occur. Carefully wipe off the liquid using a cloth and avoid contact with the skin when you notice liquid on the batteries.
• In case of contact with skin or eyes, rinse immediately with clean water and seek medical attention.
• At the end of its service, dispose of the device with due care to protect the environment.

ENVIRONMENTAL DISPOSAL

• To avoid transportation damages, the tool has to be delivered in solid packaging. Packaging as well as the unit and accessories are made of recyclable materials and can be disposed of accordingly.
• The tool’s plastic components are marked according to their material, which makes it possible to be environmentally friendly and differentiated because of available collection facilities.

Only for EU countries

• Do not dispose of electric tools together with household waste material!
• In observance of European Directive 2002/96/EC on waste electrical and electronic equipment and its implementation under national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

WARRANTY

• The electrical appliances have been manufactured according to strict standards, set by our company, which are aligned with the respective European quality standards.
• The electrical appliances of our company are provided with a warranty period of 24 months for non-professional use and 12 months for professional use.
• The warranty is valid from the date of purchase of the product. Proof of the warranty right is the purchase document of the appliance (retail receipt or invoice).
• Under no circumstances shall the company cover the relevant cost of spare parts and respective required working hours unless a copy of the purchase document is presented.
• In case the repair has to be done by our service department the cost of transportation (to and from) is entirely borne by the sender (client).
• The electrical appliances must be sent for repair to the company or to an authorized workshop in the appropriate way and means of transport.

WARRANTY EXEMPTIONS AND RESTRICTIONS:

1. Spare parts that wear out naturally as a consequence of being used (brushes, cables, switches, chargers, chucks, etc.).
2. Electrical appliances were damaged as a result of non-compliance with the instructions of the manufacturer.
3. Electrical appliances are poorly maintained.
4. Use of inappropriate accessories.
5. Electrical appliances are given to third entities free of charge.
6. Damage due to an electrical connection at a voltage other than that indicated on the appliance plate.
7. Connection to a non-earthed power supply.
8. Change in current voltage.
9. Damage resulting from the use of salty water.
10. Damage or malfunction resulting from improper cleaning procedure of the appliance.
11. Contact of the electrical appliance with chemicals, or damage as a result of moisture or corrosion.
12. Electrical appliances that have been modified or opened by unauthorized personnel.
13. Broken parts/components as a result of inappropriate use.
14. Electrical appliances used for rent.

• The warranty covers only the free-of-charge replacement of the component that presents a manufacturing defect or material failure.
• In case of a lack of a specific spare part, the company reserves the right to replace the electrical appliance with another corresponding model.
• After all warranty procedures have been concluded, the warranty period of the electrical appliance shall not be extended or renewed.
• Τhe replacement of a spare part, along with the repair charge, is covered by a 1 year warranty of good operation, provided that the warranty terms are met.
• The spare parts or electrical appliances that are replaced remain in the possession of our company. Requirements, other than those mentioned in this warranty form, regarding the repair of electrical appliances or damage thereof, do not apply.
• Greek law and relative regulations apply to this warranty.
• The instructions manual is also available in digital format on our website www.nikolaoutools.com. Find it by entering the product code in the Search field.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>