Silk n SILKYAIR PRO HDB003 Hair Dryer User Manual

Silk n SILKYAIR PRO HDB003 Hair Dryer User Manual

Legal notice

Invention Works B.V. reserves the right to make changes to its products or specifications to improve performance, reliability, or manufacturability. Information furnished by Invention Works B.V. is believed to be accurate and reliable at the time of publication. However, Invention Works B.V. assumes no responsibility for its use. No license is granted by its implication or otherwise under any patent or patent rights of Invention Works B.V.
No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Invention Works B.V. Data is subject to change without notification.
Silkn Beauty Ltd. has patents and pending patent applications,
trademarks, copyrights, or other intellectual property rights
covering subject matter in this document. The furnishing of this
document does not give you any license to these patents, trademarks, copyrights, or other intellectual property rights except as
expressly provided in any written agreement from Silkn Beauty
Ltd. Specifications are subject to change without notice.
Silk’n and the Silk’n logo are registered trademarks of Silkn Beauty
Ltd.
Invention Works B.V.
Galileïstraat 17, 3029 AL Rotterdam, The Netherlands www.silkn.com, www.silkn.ca – info@silkn.com 

Safety instructions

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE  USING
KEEP AWAY FROM WATER
DANGER – As with most electrical appliances, electrical parts are electrically live even when the switch is off:

To reduce the risk of death by electric shock:

1. Always unplug the appliance immediately after using.
2. Do not use while bathing.
3. Do not place or store the appliance where it can fall or be pulled into a tub or sink.
4. Do not place in or drop into water or other liquid.
5. If an appliance falls into water, unplug it immediately. Do not reach into the water

WARNING – To reduce the risk of burns, electrocution, fire, or injury to persons:

1. An appliance should never be left unattended when plugged in.
2. Close supervision is necessary when this appliance is used by, on, or near children or individuals with certain disabilities.
3. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
4. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped, damaged, or dropped into water. Return the appliance to a service center for examination and repair.
5. Keep the cord away from heated surfaces. Do not wrap the cord around the appliance.
6. Never block the air openings of the appliance or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the EN like.
7. Never use while sleeping.
8. Never drop or insert any object into any opening or hose.
9. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
10. Do not use an extension cord with this appliance.
11. Do not direct hot air toward eyes or other heat sensitive areas.
12. Attachments may be hot during use. Allow them to cool before handling.
13. Do not place the appliance on any surface while it is operating.
14. While using the appliance, keep your hair away from the air inlets.
15. Do not operate with a voltage converter

SAVE THESE INSTRUCTIONS

SERVICING OF DOUBLE-INSULATED APPLIANCES
In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double-insulated appliance requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated appliance must be identical to the parts they replace. A double-insulated appliance is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED”. The symbol ( square within a square) may also be marked on the appliance.

OPERATING INSTRUCTIONS

This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

ALCI SAFETY DEVICE

This appliance is provided with a protective device that may make the appliance inoperable under some abnormal conditions. If the appliance becomes inoperable, discard the appliance or return the appliance to a service center for examination and repair.

ALCI (Appliance Leakage Current Interrupter) SAFETY DEVICE:
This device provides protection against electric shock due to ground fault currents by automatically shutting off the power. The TEST and RESET buttons on the ALCI plug are used to check if the device is functioning properly. It is recommended to check the device monthly. To do so:

1. Press the TEST button.
2. The RESET button should pop up. If not, do not use the product.
3. Press the RESET button to restore power. If the TEST button is pressed and the product can still be turned on, current leakage has been detected. Do not use the product or attempt to reset the ALCI safety device.

WARNING

• DO NOT press the TEST button while the product is operating.
• The TEST and RESET buttons should not be used as “ON” and “OFF” switches.
• The cord and plug are not intended to offer protection to externally connected loads or supply circuits.
• The cord and plug are intended for indoor use only.

Package contents/device parts

1. Air outlet
2. Cool shot button
3. Handle
4. Power cord
5. Speed button
6. Temperature button
7. Standby switch
8. Display
9. Cool air indicator
10. Temperature indicator
11. Speed indicator, 3x
12. Lock icon
13. Concentrator, 2x (small/wide)
14. Diffuser
15. Filter
16. Rear cover

Operation

• Clean all parts of the product before first use as described in the chapter “Cleaning”.
• The product may emit a slight smell when it is first used. This is entirely safe and harmless. Ensure there is adequate ventilation in the room.
• Always hold onto the handle 3 when using the product.

1. Connect the power cord 4 to an easily accessible power outlet.
2. If necessary, attach one of the attachments (concentrator (small/ wide) 13 or diffuser 14 ) to the air outlet 1 **(see Fig. B).

** The attachments magnetically fix to the air outlet.

3. To switch the product on, slide the standby switch 7 to the middle position (ON).

4. To change the operating temperature, press the temperature button 6 repeatedly until the desired temperature (39, 55, 65, 75, 85 or 95 °C / 102, 131, 149, 167, 185 or 203 °F) is selected.
   The operating temperature shows in the temperature indicator 10 of the display 8 .

5. To change the operating speed, press the speed button 5 repeatedly until the desired speed (3 levels) is selected. One or more speed indicators 11 illuminate to show the selected speed level (1–3).

6. For a shot of cool air, press and hold the cool shot button 2 . The cool air indicator 9 illuminates when the function is activated. Release the button to cancel this function.

7. To lock the selected temperature and speed, slide the standby switch to the top position (   ). The lock icon 12 illuminates when the function is activated.

8. To switch the product off, slide the standby switch to the bottom position (OFF). The product remembers the last temperature and speed for your next use.

USER-MAINTENANCE INSTRUCTIONS

The appliance is virtually maintenance-free. No lubrication is needed. Keep heated surfaces clean and free of dust, dirt, and hair spray. If cleaning becomes necessary, unplug the appliance from the power source and wipe the exterior with a damp cloth. If the cord becomes twisted, untwist prior to use.
WARNING: The product is not intended to be opened and/or repaired by the user. Repair of the product shall be performed by an authorized person or in the certified service centre only

Cleaning

WARNING! RISK OF INJURY!

• Always disconnect the power cord and let the product completely cool down before cleaning.

NOTICE! RISK OF DAMAGE!

• Never immerse the product in water or other liquids. Make sure that no water or other liquids penetrate the housing.
• Do not use any aggressive cleaners, brushes with metal or nylon bristles, or sharp or metallic cleaning utensils such as knives, hard scrapers and the like.

1. Clean the product with a damp cloth.
2. Dry the product thoroughly with a soft and clean cloth.

Internal cleaning

• With this function, the motor operates in reverse direction to draw air from the air outlet 1 and clean the internal parts of the product with cool air.
• Only use this function periodically. Overuse may damage the product.

1. Connect the power cord 4 to an easily accessible power outlet.
2. Within 10 seconds, press and hold the temperature button 6 and speed button 5 at the same time for about 3 seconds to activate the internal cleaning mode. The product operates in reverse direction for about 10 seconds before stopping automatically.
3. If necessary, repeat step 2 to activate this function again. You can only activate this function 3 times at a time. To enter the internal cleaning mode again, you must unplug the product and start over again.

Cleaning the filter

To avoid the accumulation of dust inside the product, clean the filter every 2 weeks and replace it every month. New filters can be purchased on our website [(www.silkn.com](http://\(www.silkn.com) or www.silkn.ca).

1. Rotate the rear cover 16 anticlockwise to detach it and remove the filter 15 from the product (see Fig. C).
   
   If necessary, insert a small tool between the grilles of the rear cover and then rotate the rear cover with the tool.

2. Wash the filter with clean water and then air dry it. The filter must be fully dry. Otherwise, it may damage the product.

3. Place the filter and rear cover back onto the product. There are small and large tabs on the rear cover. Make sure the small tabs are on the top and bottom, and the large tabs are on the sides when attaching the rear cover ( see Fig. C).

4. Rotate the rear cover clockwise until it locks into place.

STORAGE INSTRUCTIONS

• Unplug the appliance when not in use.
• Allow the appliance to cool and store it out of reach of children in a safe, dry location. Never wrap the cord around the appliance since this will cause the cord to wear prematurely and break. Handle the cord carefully for longer life and avoid jerking, bending sharply, twisting, or straining the cord, especially at plug connections.
• All parts must be completely dry before being stored. Store the product in a clean and dry place, avoiding heat and direct sunlight.

STOP:
IF YOU MUST USE YOUR PRODUCT IN THE BATHROOM, INSTALL A GFCI* NOW! Your local electrician can help you decide which type is best for you – A portable unit that plugs into the electrical outlet or permanent unit installed by your electrician. The National Electric Code now requires GFCI’s in the bathroom, garages, and outdoor outlets of all NEW homes.

This message about

WHY DO YOU NEED A GFCI?
Electricity and water don’t mix. If your hair dryer falls in water while it’s plugged in, the electric shock can kill you…even if the switch is “OFF”.

Ground Fault Circuit Interrupters
can save a life!
A regular fuse or circuit breaker won’t protect you under these circumstances. A GFCI offers you far greater protection.
A GFCI can save your life! Compared to that, the price is small! Don’t wait…install one now!
*GFCI is a sensitive device which reacts immediately to a small electric current leak by stopping the electricity flow.

General information

Reading and storing the user manual

This user manual accompanies this hair dryer Silky Air Pro HDB003 (hereafter referred to as the “product”), and contains important information on setup and handling.
Before using the product, read the user manual carefully. This particularly applies to the safety instructions. Failure to do so may result in personal injury or damage to the product. Store the user manual for further use. Make sure to include this user manual when passing the product on to third parties.

Explanation of symbols

The following symbols and signal words are used in this user manual, on the product or packaging .

WARNING!
This signal symbol/word designates a hazard with a moderate risk, which may result in death or severe injury if not avoided.

NOTICE!
This signal word warns of possible damage to property.

This signal symbol provides you with useful additional information on handling and use.

This symbol identifies electrical devices that belong to the protection class II.
WARNING: Do not use the product in the vicinity of bathtubs, showers, washbasins or other vessels containing water
Proper use
The product is exclusively designed for drying and styling human hair. It is only intended for private use and not suitable for commercial purposes. Only use the product as described in this user manual. Any other use is considered improper and may result in damage to property or persons. The manufacturer cannot be held liable for damages or injury incurred through improper or incorrect use.

Checking the product and package contents

NOTICE! RISK OF DAMAGE!

• If you are not cautious when opening the packaging with a sharp knife or other pointed objects, you may quickly damage the product. Be very careful when opening it

1. Take the product out of the packaging.

2. Check to make sure that all parts are included (see Fig. A).
   

3. Check whether the product or individual parts are damaged. If this is the case, do not use the product. Contact our customer service.

Troubleshooting

Some problems may be caused by minor faults that you can fix yourself. To do so, follow the instructions in the following table. If it is still not possible to resolve the problem, contact customer service. Do not repair the product yourself.

• Make sure the product or power cord is not defective, and the power cord is properly connected to a power outlet.
• The product overheats. Unplug the product and wait until it has completely cooled down before using again.

The hair is singed.|

• The selected operating temperature is too high. Select a lower temperature.

Error message E01 or E04–E10 shows in the display.|

• There is an internal error. Contact customer service for support.

• The voltage is either too low or high. Connect the product to an appropriate power outlet.

Technical data

Model: HCA01NA
Voltage: 125 V~, 50/60 Hz
Power: 1,600 W
Motor speed: 110,000 rpm
Max. air speed : 47.2 mile/hr (76 km/hr)
Noise level: ≤ 75.7 dB (11.8 inches/30 cm)
Weight: 24.5 oz (695 g)

FCC statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Disposal

Disposing of the packaging

Sort the packaging before you dispose of it. Dispose of paperboard and cardboard with the recycled paper service and wrappings with the appropriate collection service.

Disposing of the product
Old appliances may not be disposed of in the household waste!
Should the product no longer be capable of being used at some point in time, dispose of it in accordance with the regulations in force in your city or county. This ensures that old appliances are recycled in a professional manner and also rules out negative consequences for the environment.

Warranty

This product is covered by a 1-year warranty. The extent of the warranty on this product is limited to technical defects caused by faulty production processes. In the event you want to claim warranty please be sure to contact our customer service for instructions. They may be able to solve your problem without needing to return the product to the store or our service center. Our customer service is always pleased to help you!

Customer service

For more information about the products of Silk’n visit your regional Silk’n website: www.silkn.com or www.silkn.ca. If the device is damaged, defective, in need of repair or you need our assistance, please contact your nearest Silk’n service center. This manual is also available as a PDF download from: www.silkn.com or www.silkn.ca.  
Service number: 1-800-250-5053
Email: customercarena@silkn.com

References

• Beauty Tools for Home Use | Silk'n
• Beauty Tools for Home Use | Silk'n

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>