HYUNDAI HYUWS1070 Weather Station Instruction Manual

: June 3, 2024
: HYUNDAI

Table of Contents

HYUWS1070 Weather Station
FEATURES
POWERING ON
REMOTE FREQUENCY FUNCTION
RADIO SIGNAL SEARCH
TEMPERATURE
BACKLIGHT FUNCTION
Documents / Resources

HYUWS1070 Weather Station
Instruction Manual

HYUWS1070 Weather Station

FEATURES

6 buttons: ‘SET’, ‘CH’, ‘UP’, ‘DOWN’, ‘SNZ’, ‘ALARM’
Time and calendar display
Alarm and snooze function with blue backlight
Low power reminding of both indoor and outdoor machine
The displaying range of indoor temperature: 0 – 50 °C
The displaying range of outdoor temperature: -20 – 50 °C
Display 3 different places of temperature in 3 different channels
Radio controlled time, DCF frequency 77,5 kHz
DST time
Record the highest and lowest temperature of both indoor and outdoor
operated with 2 x AAA batteries (not included) for clock and 2 x AAA batteries (not included) for transmitter

POWERING ON

Open the battery compartment cover and insert 2 x AAA batteries according to the correct polarity showed in the compartment. After powering on, the clock will take about 3 minute to connect with the outdoor transmitter. After that, it will start search radio signal. It will stop searching signal till successfully received or 7 minutes later.

REMOTE FREQUENCY FUNCTION

The clock will take about 3 minutes to receive the temperature from outdoor transmitter once powering on or resetting. Keep pressing ‘CH’ button for seconds to clear up the temperature which received previously and it will start connecting with outdoor transmitter again. When the clock is receiving the data from the outdoor transmitter, the signal will flash.
The clock will not search for the signal from outdoor transmitter if there is no signal received from outdoor transmitter in 3 channels after powering on or resetting.
The clock will not search for the signal from outdoor transmitter anymore if there is no signal received in 1 hour. It will display ‘—‘.
Wireless Outdoor Sensor: 433,92 MHz RF transmitting frequency; ERP: 0,05 mW

RADIO SIGNAL SEARCH

RC signal searching condition:
The clock will start search the signal automatically after transmitter connecting with clock when powering on or resetting. Under normal time displaying mode, keep pressing ‘DOWN’ button to enter into RC signal searching. RC signal searching will start everyday automatically and it will last about 10 minutes. Automatically search radio signal to adjust time at 1:00 am, 2:00 am, 3:00 am, 4:00 am and 5:00 am. If there is no signal received or before 3:00 am, it will automatically start searching at 4:00 am and 5:00 am. If signal received at 4:00 am, it will not search signal that day. No matter the signal received at 5:00 am or not, there will not search again that day. RC time searching will last 10 minutes.

RCC Receiving Icon:
When the clock is searching signal, RC icon will be flashing.
After signal successfully received, LCD will display completed RC icon which will stop flashing, and existing RC searching.
Under the searching mode, press ‘DOWN’ button to exist RC searching.
If no signal received that day, next searching time will be at 1:00 am next day.
If alarm rings while searching RC signal, the clock will continue searching RC signal.
When receive DST, the DST symbol will display on the LCD screen

Manual TIME SETTING

At normal time displaying mode, keep pressing ‘SET’ button for seconds till entering time setting mode, and the setting digit will flash. Press ‘UP’ or ‘DOWN’ button to adjust. The setting order is 12 / 24hr → time zone → hour → minute → year → month →date → exit. If there is no more operation for 20 seconds, it will save the existing setting and turn to normal displaying or press ‘SET’ button again to confirm the setting.

ALARM AND SNOOZE SETTING
At normal time displaying mode, press ‘ALARM’ button once to check the alarm time. Hold pressing ‘ALARM’ button to enter the alarm setting mode, the setting digit will flash. Press ‘UP’ and ‘DOWN’ button to adjust, press ‘ALARM’ button again to confirm the setting. The setting order is hour  minute  exit. If there is no more operation for 30 seconds, it will save the existing setting and turn to normal displaying.
At the mode of alarm, press’ ALARM’ button once to turn on the alarm function and the signal of is showed on the screen. Press ‘ALARM’ button again to turn off the alarm function.
The alarm sound will last for 2 minutes and it will change as below:

0 – 9 seconds: BI per second
10 – 29 seconds: BI BI per second
30 – 58 seconds: BI BI BI per second

59 seconds: Keep BI

When alarm ring is on, press ‘SNZ’ button to turn off the sound and it will be on again after 5 minutes and the signal of is flashing on the screen. Press any other button to turn off the snooze function.
When the alarm ring is on, press any other button to cancel the alarm sound. The alarm will be on again after 24 hours.

TEMPERATURE

Press ‘DOWN’ button to change the temperature in °C or °F.
Press ‘UP’ button to display the highest and lowest temperature record in 24 hours. At this time,the signal of ‘24H’ display on the screen.
Keep pressing ‘UP’ button for seconds to clear up the record of max and min temperature.
If there is signal of ‘24H’ displaying on the screen, it will clear up the record in 24 hours.

BACKLIGHT FUNCTION

Press SNZ button to turn on backlight. Backlight will light up for 5 seconds.
WE RESERVE THE RIGHT TO CHANGE TECHNICAL SPECIFICATIONS.
TO AVOID DANGER OF SUFFOCATION, KEEP THE PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.

Disposal of old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems).
**** This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will
help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.
Hereby, ETA a.s. declares that the radio equipment type WS1070 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www .hyundai-electronics.cz/declaration_of_conformity

Licensed by Hyundai Corporation Holdings, Korea
Imported by ETA a. s., náměstí Práce 2523, 760 01 Zlín, CZ