ELKO ep 8310 Wireless Light Dimmer Key Fob Instruction Manual

ELKO ep 8310 Wireless Light Dimmer Key Fob

WIRELESS LIGHT DIMMER

KEY FOB

Combination of iNELS switching element for universal use. It can be used to control electrical appliances, lights, sockets, garage doors, etc.

Content

Controller – key fob RF KEY-40/W, RF KEY-40/B
Universal dimmer, 1-channel
RFDEL-71B-SL

EAN 8595188183109 (key fob – black + Universal dimmer, 1-channel) EAN 8595188183116 (key fob – white + Universal dimmer, 1-channel) EAN 8595188183123 (key fob – black + 2 x Universal dimmer, 1-channel) EAN 8595188183130 (key fob – white + 2 x Universal dimmer, 1-channel)

The individual elements in the iNEL S set are paired and their functions are preset.
iNELS kit with key fob enables the basic function of controlling electrical appliances – ON / OFF. The appliances can be controlled independently by a key fob.

The settings of the wall controllers can be changed – see detailed manuals of iNELS elements.

Controller – key fob
RF KEY-40/W, RF KEY-40/B

RF KEY 40/B – key fob , black RF KEY 40/W – key fob , white

Characteristics

•  Key fob-sized remote control – used to control, lights, gate, garage door, shitters, etc.
• 4 buttons, each of which allows you to control an unlimited number of components.
•  Replaceable battery (3 V CR 2032 – included in the package) with a service life of approx. 5 years (depen-ding on the frequency of use).

**Insertion and replacement of a battery RF KEY-40

**

• Use a coin to open the key fob and remove the front cover. Carefully tap the device out of the bottom cover.
• Slide the CR2032 battery into the battery holder. Observe the polarity.
• Insert the device into the bottom cover. Attach the front of the cover and click.

Safe handling

When handling a device unboxed it is important to avoid contact with liquids. Never place the device on the conductive pads or objects, avoid unnecessary contact with the components of the device.

Technical parameters

Other data
Operating temperature:| -10 … +50 °C (14 … 122 °F)
Operating position:| any
Colour design| white, black
Protection:| IP20
Pollution degree:| 2
Dimensions:| 64 x 25 x 10 mm
Weight:| 16 g
Related standards:| EN 60669, EN 300 220, EN 301489,

No 426/2000 Coll.

Attention
When you install iNELS RF Control system, you have to keep a minimal distance of 1 cm (0.4“) between each unit. Between the individual commands must be an interval of at least 1s.

Universal dimmer, 1-channel RFDEL-71B-SL

Characteristics

• The universal built-in dimmer is used to regulate light sources.
• They can be combined with detectors, controllers, iNELS RF Control or system components.
• 7 light functions – smooth increase or decrease with time setting 2s-30 min. + additional function SWITCH OFF
• Thanks to setting the min. brightness you will eliminate fl asking of the LED and ESL light sources
• The universal dimmer may be controlled by up to 25 channels (1 channel represents 1 button).
• Connection of the existing button on the control input “S“ enables combination of wireless control with classic (wired) control.
• The programming button on the controller is also used for manual control of the output.
• For components labelled as iNELS RF Control2 (RFIO2), it is possible to set the repeater function via the RFAF/USB service device.
• Range up to 200 m (in open space), if the signal is insufficient between the controller and unit, use the signal repeater RFRP-20 or protocol component RFIO2 that support this feature.

Installation options

Output:
Contactless:| 2 x MOSFET
Load capacity:| 300 W *
Control:
RF command from the transmitter:| 868.5 MHz
Range in open space:| up to 200 m
Manual control:| button PROG (ON/OFF), external button
Other data:
Operating temperature:| -15 … + 45 °C
Storage temperature:| -30 … +70°C
Operating position:| any
Protection:| IP30 under normal conditions
Overvoltage category:| III.
Contamination degree:| 2
Connection:| screwless terminals
Connecting conductor:| 0.2-1.5 mm2
Dimensions:| 43 x 44 x 22 mm
Weight:| 30 g
Related standards:| EN 60730, EN 63044, EN 300 220, EN 301 489

Radiofrequency signal penetration through various construction materials
Range up to 200 m in open space, if the signal is insufficient between the controller and unit, use the signal repeater RFRP-20 or protocol component RFIO2 that supports this feature.

Warning
Instruction manual is designated for mounting and also for the usage of the device. It is always a part of its packing. Installation and connection can be carried out only by a person with adequate professional qualification with understanding this instruction manual and functions of the device, and while observing all valid regulations. Trouble-free function of the device also depends on transportation, storing and handling. In case you notice any sign of damage, deformation, malfunction or missing part, do not install this device and return it to its seller. It is necessary to treat this product and its parts as electronic waste after its lifetime is terminated. Before starting installation, make sure that all wires, connected parts or terminals are de-energized. While mounting and servicing observe safety regulations, norms, directives and professional, and export regulations for working with electrical devices. Do not touch parts of the device that are energized – life threat. Due to transmissivity of RF signal, observe correct location of RF components in a building where the installation is taking place. RF Control is designated only for mounting in interiors. Devices are not designated for installation into exteriors and humid spaces. The must not be installed into metal switchboards and into plastic switchboards with metal door – transmissivity of RF signal is then impossible. RF Control is not recommended for pulleys etc. – radio-frequency signal can be shielded by an obstruction, interfered, battery of the transceiver can get fl at etc. and thus disable remote control.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>