ELKO ep 8327 Wireless Dimming Socket Instruction Manual
- June 4, 2024
- ELKO ep
Table of Contents
WIRELESS DIMMING
SOCKET
(LUXURY VERSION)
Combination of iNELS wall-mounted wireless controller and wireless dimming socket for regulation of all types of dimmable bulbs and light sources.
Content
Glass touch controller – 4 buttons, SHARP RFGB-40/W, RFGB-40/B
Glass touch controller – 4 buttons, ROUND RFGB-240/W, RFGB-240/B
Dimming socket-plug RFDSC-71N
Design
EAN 8595788183277 (Glass touch controller – 4 buttons, SHARP, black + Dimming
socket-plug “French“)
EAN 8595788183284 (Glass touch controller – 4 buttons, SHARP white + Dimming
socket-plug “French““)
EAN 8595788183291 (Glass touch controller – 4 buttons, ROUND, black + Dimming
socket-plug “French““)
EAN 8595788183307 (Glass touch controller – 4 buttons, ROUND, white + Dimming
socket-plug “French““)
EAN 8595788183376 (Glass touch controller – 4 buttons, SHARP, black + Dimming
socket-plug “British“)
EAN 8595788183383 (Glass touch controller – 4 buttons, SHARP, white + Dimming
socket-plug “British“)
EAN 8595788183390 (Glass touch controller – 4 buttons, ROUND, black + Dimming
socket-plug “British“)
EAN 8595788183406 (Glass touch controller – 4 buttons, ROUND, white + Dimming
socket-plug “British“)
EAN 8595788183475 (Glass touch controller – 4 buttons, SHARP, black + Dimming
socket-plug “Schuko“)
EAN 8595788183482 (Glass touch controller – 4 buttons, SHARP, white + Dimming
socket-plug “Schuko“)
EAN 8595788183499 (Glass touch controller – 4 buttons, ROUND, black + Dimming
socket-plug “Schuko“)
EAN 8595788183505 (Glass touch controller – 4 buttons, ROUND, white + Dimming
socket-plug “Schuko“)
The individual elements in the iNELS set are paired and their functions
are preset.
iNELS wireless dimming socket enables dimming of different types of lights or
controlling electrical appliances
The settings of the wall controllers can be changed – detailed manual on the next pages.
Glass touch controller – 4 buttons,
SHARP/ROUND, RFGB-40/RFGB-240
RFGB-40/B – glass touch controller, SHARP – black, 4-buttons
RFGB-40/W – glass touch controller, SHARP – white, 4-buttons
RFGB-240/B – glass touch controller, ROUND – black, 4-buttons
RFGB-240/W – glass touch controller, ROUND – white, 4-buttons
|
---|---
https://elko.li/rfgb-40| https://elko.li/rfgb-240
Characteristics
- The wireless control – is used to control, lights, gates, garage doors, shutters, etc.
- The thickness is only 8 mm.
- 4 capacitive buttons allow you to control 4 components.
- Fast installation on any surface – the rear base allows screwing to the walls, gluing with double-sided tape, or just laying on the table.
Replacement of a battery in 3 steps
Assembly
Adhesive
| |
---|---|---
Peel off one protective layer on the double-sided adhesive sheets and stick
them to the marked places on the controller.| Peel off the second protective
layer on the double-sided adhesive sheets and place the control in the
prepared place.| If the device is installed on glass, cover it with a cover
foil
In the installation box or on the wall
| |
---|---|---
Mount the snap bar on the controller into the installation
box or on the wall| Place the mounting jig on the KU box and screw it on| Snap
on the controller.
Technical parameters| RFGB-40/RFGB-240
---|---
Power voltage:| 2x 3 V battery CR 2032
---|---
Battery life:| about 2 years depending on the frequency of use
Transmission indication| Red LED
A number of capacitive buttons:| 4
Communication Protocol:| RFIO2
Frequency:| 868.5 MHz
Signal transmission method:| one-way addressed message
Range:| in the open up to 200 m
Material:| Glass
Other data
Operating Temperature:| -10 … +50 °C (14 … 122 °F)
Working Position| any
Mounting:| adhesive, screw
Protection| IP20
Pollution degree:| 2
Dimension:| SHARP 94 x 94 x 8 mm (3.7“ x 3.7“x 0.3“) / ROUND 100 x 100 x 8 mm
(3.9“ x 3.9“ x 0.3“)
Weight:| SHARP 107 g/ ROUND 108 g
Related standards:| EN 60669, EN 300 220, EN 301 489
Dimming socket plug RFDSC-71N
Characteristics
- used to control light sources that are connected by power cord – especially lamps: R, L, C, ESL, LED – LED light sources (230V).
- Be combined with detectors, controllers, iNELS RF Control, or system components.
- Installation is simple by direct insertion into the existing socket.
- Output load 200 W.
- 7 light functions – smooth increase or decrease with time setting 2s-30 min. + Additional function SWITCH OFF
- When switched off, the set level is stored in the memory, and when switched back on, it returns to the most recently set value.
- The universal dimmer may be controlled by up to 32 channels (1 channel represents 1 button on the controller).
- The programming button on the socket is also used for manual control of the output.
- Memory status can be pre-set in the event of a power failure.
- Range up to 160 m (in open space), if the signal is insufficient between the controller and unit, use the signal repeater RFRP-20 or protocol component RFIO2 that supports this feature.
Assembly
Technical parameters | RFDSC-71N |
---|---|
Supply voltage: | 230 V / 50-60Hz |
--- | --- |
Apparent power: | 1.1 VA |
Dissipated power: | 0.8 W |
Supply voltage tolerance: | +10 %; -15 % |
Output:
Contactless:| 2 x MOSFET
Load capacity:| 200 W *
Control:
RF command from the transmitter:| 868.5 MHz
Range in open space:| up to 160 m
Manual control:| button PROG (ON/OFF)
Other data:
Operating temperature:| -20 … + 35 °C (-4 … + 95 °F)
Storage temperature:| -30 … +70°C (-22 … + 158 °F)
Working position:| any
Mounting:| plug into a socket
Protection:| IP30
Overvoltage category:| III.
Contamination degree:| 2
Dimensions:| 63 x 110 x 74 mm
Weight:| 118 g
Related standards:| EN 60730, EN63044, EN 300 220, EN 301 489
- capacity for power factor cos φ=1
The power factor of dimmable LEDs and ESL bulbs ranges from: cos φ = 0.95 up to 0.4.
Compatibility
The device can be combined with all system components, controls, and devices
of iNELS RF Control and iNELS RF Control 2. The detector can be assigned an
iNELS RF Control2 (RFIO 2 ) communication protocol.
Radiofrequency signal penetration through various construction materials
Range up to 160 m in open space,
60 – 90 %| 80 – 95 %| 20 – 60 %| 0 – 10 %| 80- 90 %
brick walls| wooden structures with plasterboards| reinforced concrete| metal
partitions| common glass
Warning
The instruction manual is designated for mounting and also for the usage of
the device. It is always a part of its packing. In-installation and connection
can be carried out only by a person with adequate professional qualification
with an understanding of this instruction manual and functions of the device,
and while observing all valid regulations. The trouble-free function of the
device also depends on transportation, storing, and handling. In case you
notice any sign of damage, deformation, malfunction, or missing part, do not
install this device and return it to its seller. It is necessary to treat this
product and its parts as electronic waste after its lifetime is terminated.
Before starting the installation, make sure that all wires, connected parts,
or terminals are de-energized. While mounting and servicing observe safety
regulations, norms, directives, and professional, and export regulations for
working with electrical devices. Do not touch parts of the device that are
energized – a life threat. Due to the transmissivity of RF signal, observe the
correct location of RF components in a building where the installation is
taking place. RF Control is designated only for mounting in interiors. Devices
are not designated for installation in exteriors and humid spaces. The must
not be installed into metal switchboards and into plastic switchboards with
metal door – transmissivity of RF signal is then impossible. F Control is not
recommended for pulleys etc. – the radiofrequency signal can be shielded by an
obstruction, interfered, battery of the transceiver can get fl at etc. and thus
disable remote control.
Designed & Manufactured by:
ELKO EP, s.r.o. Palackého 493, 769 01 Holešov, Všetuly,
Czech republic, www.elkoep.com, Hotline: +420 800 100
671