ELKO ep SHT-13 Multifunction Digital Time Switch with Wi-Fi Connection User Guide
- June 1, 2024
- ELKO ep
Table of Contents
- SHT-13 Multifunction Digital Time Switch with Wi-Fi Connection
- Product Specifications
- Product Usage Instructions
- Initial Setup:
- Programming Channels:
- Maintenance:
- Output Protection:
- Operating Modes:
- Q: What is the maximum inrush current supported by the
- Q: Can the device retain set values in case of a mains power
- Q: How can I access the programming menu?
SHT-13 Multifunction Digital Time Switch with Wi-Fi Connection
Product Specifications
-
Brand: ELKO EP, s.r.o.
-
Model: SHT-13, SHT-13/2
-
Made in: Czech Republic
-
Connection: Wi-Fi
-
Supply Voltage: A1-A2
-
Consumption (max.): Wi-Fi OFF 0.5 W/2 VA | ON 1 W/3 VA
-
Output Contact Type: Rated current: 30 A; Switched power: 4000
VA/AC1, 384 W/DC1 -
Switching Voltage: 250 V AC/24 V DC
-
Time Circuit Accuracy: Min. switching interval: 10 years; Data
retention time: up to 120 days -
Program Circuit: Number of memory locations: 200; Program type:
daily, weekly, yearly, astro -
Operating Temperature: Any; Storage Temperature: -15% to
+10% -
Mounting: DIN rail EN 60715
-
Protection Degree: IP40 front panel / IP20 terminals
-
Weight: 122 g (SHT-13), 135 g (SHT-13/2)
Product Usage Instructions
Initial Setup:
A first setup wizard will guide you through the initial
configuration after inserting the battery or connecting to the
power supply.
Programming Channels:
Each channel can be assigned a different program or operating
switching mode, allowing control of two independent circuits.
Maintenance:
After installation, the device does not require any special
service or maintenance.
Output Protection:
Ensure a class B circuit breaker with a minimum output
protection of 16A is used.
Operating Modes:
-
AUTO: Changes automatically according to the entered time
zone. -
OFF: Permanently switched off winter/summer time
transition.
Frequently Asked Questions (FAQ)
Q: What is the maximum inrush current supported by the
device?
A: The device supports an inrush current of less than 3 seconds
at 30A.
Q: Can the device retain set values in case of a mains power
failure?
A: Yes, the device will retain all the set values required for
reliable switching after power is restored.
Q: How can I access the programming menu?
A: Use the control buttons to enter the programming menu and
browse through settings.
EN
ELKO EP, s.r.o.
Palackého 493 769 01 Holesov, Vsetuly Czech Republic Tel.: +420 573 514 211
e-mail: elko@elkoep.com www.elkoep.com
Made in Czech Republic
02-71/2017 Rev.: 3
SHT-13, SHT-13/2
Multifuntion digital time switch with Wi-Fi connection
Characteristics
Symbol
· All programs in one device (daily, weekly, yearly and astronomical). ·
UNIversal supply voltage in range of AC/DC 24 – 240 V (AC 50-60 Hz). · Simple
setting after the first start-up. · User replaceable battery to back up the
set time. · Built-in web server for setup and control via Wi-Fi connection. ·
Time synchronization through NTP server (require internet connection). · New
well-arranged display with white backlight. · ASTROnomic program: manual entry
of coordinates or selecting one of the preset
cities. · One/two channel design (each with an operating hours counter). ·
Pulse/cycle output mode. · Transition of summer/winter time – AUTO or OFF. ·
Lead-sealing transparent front panel cover. · PIN code protection against
unauthorized changes. · Wireless firmware update.
SHT-13
A1
A2
Connection
SHT-13
Un
16 18 15
A1 16 15 18
SHT-13/2
A1
A2 SHT-13/2
Un
16 18 26 28
15
25
A1 16 15 18
A first setup wizard will guide you through the initial configuration after inserting the battery or after connecting to the power supply.
Each channel can be assigned a different program or operating switching mode,
this allows control of two independent circuits. In the event of a mains power
failure, the device will retain all the set values required for reliable
switching after the power is restored. After installation, it does not require
any special service or maintenance.
The astronomical program does not need any optical sensors or other external
devices to function. Its operating principle is that during the year every
day, based on an algorithm and real-time (set in the time switch),
automatically controls switching on and off times of e.g. public lighting.
This is because the sunrise and sunset times change throughout the year. With
the offset (deviation) function, the turning ON and switching OFF times can be
corrected within ± 120 minutes. The delay is fixed for each day but can be
adjusted for each channel separately.
· Operation modes of switching: (configurable for each channel separately)
–
(switches according to set time programs)
–
gram)
(switches according to set holidays and time programs (switches according to the set astronomical and time pro-
–
(switches according to set holidays, astronomi-
cal and time program)
–
(switches randomly in an interval of 10-120 min)
–
(fixed output state that cannot be changed other than through
settings)
· Possibility to manually control the output contacts at any time (outside the opera-
tion mode,
).
· 200 memory locations for time programs (common for both channels). · Up to 30 memory locations for holidays
· Programming can be done under power and in backup mode.
· Optional languages CZ / EN · Selection of summer/winter time transition:
– AUTO (changes automatically according to the entered time zone)
– OFF (permanently switched off winter/summer time transition)
· The time switch is backed up by a battery, which enables it to operate in backup mode in the event of a power failure. All settings and programs are saved in memory in the event of a power failure – they can thus be restored even in the event of a power failure and a discharged battery. However, a time correction will need to be made.
A2
A2 26 25 28
Prescribed minimum output protection: class B circuit breaker 16A.
Description
SHT-13/2 1 2
3 4
6
10
19
11
20
7
12
21
13 22
14
15
23
8
16
24 25
17
26
18
27
5
9
1\. Supply terminal (A1) 2. Backlight display 3. Reset 4. Sealing spot 5.
Supply terminal (A2) 6. Output – 1. channel (16-15-18) 7. Transparent cover 8.
Control buttons 9. Output – 2. channel (26-25-28) 10. Holiday program 11.
Output indication 12. Pulse/cycle mode 13. Astro program 14. Manual control
locked
15\. Summer time 16. Battery indication 17. Sunrise indication 18. Days in
week 19. Manual control 20. Random program 21. Time program 22. Time 23. AM/PM
24. Text line 25. Wi-Fi connection 26. Sunset indication 27. Bargraph
DISPLAY BACKLIGHT CONTROL Powered: By default, the display is backlit for 90
seconds from the time of the last press of any button. The display still
shows: the date, time, day of the week, state of contacts, and battery or the
type of program in progress. The backlight is permanently switched on/off by
long press of MAN1, MAN2, and OK buttons at the same time. When activating /
deactivating the permanent backlight, the display will briefly flash twice.
Backup mode: In the event of a power failure, the display will automatically
switch to sleep mode, during which time only the following will flash on the
display: the date, time, day of the week, and battery state. The time switch
can then be woken up at any time by pressing the OK button to the standard
mode, e.g. for setting (without working Wi-Fi or output contacts) – however,
take into account that in this case the consumption from the battery is
significantly increased, which affects its service life. It will return to
sleep mode if no buttons are pressed for 20 seconds.
Technical parameters
Control description
SHT-13
SHT-13/2
Supply terminals:
A1-A2
Supply voltage:
AC/DC 24 240 V (AC 50-60 Hz)
Consumption (max.):
Wi-Fi “OFF” 0.5 W/2 VA | “ON” 1 W/3 VA
Supply voltage tolerance:
-15 %; +10 %
Output Contact type: Rated current: Switched power: Inrush current: Switching
voltage: Power dissipation (max.): Mechanical life: Electrical life (AC1):
1× changeover (AgSnO2) 2× changeover (AgSnO2) 16 A/AC1*
4000 VA/AC1, 384 W/DC1
30 A/< 3 s
250 V AC/24 V DC
1.2 W
2.4 W
30.000.000 ops.
100.000 ops.
Time circuit Accuracy: Min. switching interval: Data retention time: Set time
backup:
max. ±0.5 s/day at 23°C (73.4 °F) 1 s
min. 10 years up to 120 days (CR 2032 – 3V)
Program circuit Number of memory locations: Program type: Displayed data:
Settings via website:
200 daily, weekly, yearly, astro LCD display with white backlight
by Wi-Fi (2.4 GHz)
Other information Operating temperature: Storage temperature:
-20 .. +55 °C (4 .. 131 °F) -30 .. +70 °C (22 .. 158 °F)
Dielectric strength:
supply output
AC 4 kV
output 1 output 2
AC 4 kV
Operating position:
any
Mounting:
DIN rail EN 60715
Protection degree:
IP40 front panel / IP20 terminals
Overvoltage category:
III.
Pollution degree:
2
Cross-wire section solid/
max. 1× 2.5, 2× 1.5/
stranded with ferrule (mm2):
max. 1× 2.5 (AWG 14)
Dimensions:
90 × 35 × 64 mm (3.5 × 1.4 × 2.5)
Weight:
122 g (4.3 oz)
135 g (4.8 oz)
Standards:
EN 61812-1
* With a permanent maximum load on the relay contacts of 16 A/AC1 and ambient temperature of +55 °C, the manufacturer recommends using a supply wire with insulation temperature resistance (min.) up to +105 °C.
Warning
This device is constructed for connection in 1-phase network AC/DC 24 240 V
and must be installed according to norms valid in the state of an application.
Installation, connection, setting and servicing must be carried out by
qualified electrician staff only, which have perfectly understood the
instructions and functions of the device. This device contains protection
against overvoltage peaks and disturbing impulses in the power supply network.
For the correct function of the protection of this device, there must be
suitable protections of higher degrees (A,B,C) installed in front of them and
according to the standards, interference of switching devices must be securely
eliminated (contactors, motors, inductive loads, etc.). Before installation,
make sure that the device is de-energized and the main switch is in the “OFF”
position. Don`t install the device to sources of excessive electromagnetic
interference. Ensure correct installation by perfect air circulation so that
during continuous operation and a higher ambient temperature, the device does
not exceed the maximum allowed operating temperature. For installation and
setting use a screwdriver with a width of approx 2 mm. Keep in mind that this
is a fully electronic device and approach accordingly with the installation.
Non-problematic function of the device is also dependent on the previous
method of transportation, storage, and handling. In case of any signs of
damage, deformation, malfunction, or missing parts, don`t install this device
and claim it at the dealer. The product must be treated as electronic waste at
the end of its life.
PRG entrance into programming menu
browsing in menu
+_
setting of values
\+ _ quick shifting during setting of
values
entrance into required menu
OK confirmation
Wi-Fi activation/deactivation
(on main screen)
ESC a step back
ESC back to the main screen
Device differs short and long button press. In the manual marked as:
– short button press (< 1s) – long button press (> 1s)
After 120s of inactivity (from the last press of any button) the device will
automatically return into the main screen.
Manual output control
output closes
output opens
01 -jul- 23
01 -jul- 23
01 -jul- 23
01 -jul- 23
– controls 1st channel
– controls 2nd channel
(SHT-13/2)
We have two types of manual controls available:
· Permanent (symbol glows)
The second highest priority of all control modes. The state of the output
cannot then be
changed other than by manual change (e.g. by switching to temporary manual
control
or by activating mode
, which has a higher priority). The last option is to
deactivate this control mode.
· Temporary (symbol flashing) Temporary manual control has the same priority
as the previous, permanent one. However, it can be changed in the future,
unlike permanent manual control, by one of the programs with a lower priority
(if configured in the time switch). With power supply disconnection, temporary
manual control is deactivated.
Modes priority
highest priority lowest priority
symbol
mode/program locked – manual control
manual control (temporary | permanent)
random holidays
time astronomic
(symbol flashes on the display)
and
can work at the same time on a single channel.
Type of load Contact material
AgSnO2, 16A Type of load Contact material AgSnO2, 16A
cos 0.95
AC1 250V / 16A
AC13 x
M AC2 250V / 5A
AC14 250V / 6A
M AC3 250V / 3A
K AC15 250V / 6A
AC5a uncompensated 230V / 3A (690VA)
AC5a compensated 230V / 3A (690VA) to max. input C=14uF
M
DC1
DC3
24V / 16A
24V / 3A
HAL.230V
AC5b 1000W
M DC5 24V / 2A
AC6a x
DC12 24V / 16A
AC7b 250V / 3A
DC13 24V / 2A
AC12 x
DC14 x
Display indication
time program is active | time program is planned for future astro program is
active | astro program is planned for future random program is active holiday
is active | holiday is planned for future
pulse program is active | cycle program is active
the device is connected via Wi-Fi to the configuration PC/ phone/… the device
has active Wi-Fi but is not connected to the configuration PC/phone/…
battery is discharged | 50% of capacity | not inserted
temporary | permanent manual control
sunrise | sunset phase of astronomic program
A pictogram with side lines indicates the flashing of the corresponding symbol
on the SHT-13 display. A pictogram without side lines indicates a constant
glow of the symbol.
THE BAR GRAPH reflects only time programs or permanent manual control! If the
segment of the given time is lit, it means that there is a scheduled time
program for switching the output for at least 1 s at the given hour. If the
segment of the given time is not lit, it means that no time program for
switching the output is scheduled at the given hour.
First setup
To set up the time switch you have two options (including canceling it),
please follow the steps below.
ENGLISH OK
first setu OK
use web in OK connect to
Now connect your configuration device (PC/Mobile/Tablet/….) to Wi-Fi (2.4 GHz)
of the time switch. SHT-13 Wi-Fi access data (default): SSID hostname: SHT-
13_barcode number Password: elkoep13 Web address for configuration:
192.168.1.1 Setup wizard will guide you through each step after opening
configurator. If you need advice on the individual steps, follow the
instructions below in the Wi-Fi connection headline.
+_
ASTRO SETTINGS :
CYCLE +_
ON TIME [
OK Off TIME
OK
START-ON START-ON
OK SUNRISE
OK SUNSET
OK
START-OFF
OK
+_
+_
+_
+_
+_
2 manually O OK OPERATION
OK CHANNEL CHANNEL
+_
2 OK lorcaAknShedToTdoRlImOiM-dE/apPyMrRToIO/GR
OK ASTRO
mode OK
CHANNEL
CHANNEL
+_
SUNSET-ON/
OK
SUNSET-off
SUSNUSNESTE-To-fOfN/
OK PULSE
+_ +_
ON / OFF
cancel set OK 01 -jan- 23
cancel setup (you can set up the device later on)
OK
PULSE TIME OK SUNRISE
OK SUNSET
OK
+_
+_
+_
OK
SUNRISE
OK SUNSET
OK
+_
+_
ASTRO SETTINGS: Menus for ASTRO settings (mode, output type, offset, location)
will pop up only if you have selected one of the ASTRO programs as operation
mode for 1st or 2nd channel. If you have selected the ASTRO program for both
channels you will need to set up the mode, output type and offset for both
since each channel can have a different setup.
ASTRO MODES: (the output of the selected channel closes
at sunset and opens at sunrise) (the output of the selected channel opens
at sunset and closes at sunrise) (the output of the selected channel closes
at sunset and sunrise) (the output of the selected channel
opens at sunset and sunrise)
COUNTRY Location OK Coordinate
+_
OK CESKA REPU OK PRAHA
+_
+_
latitude OK longitude
+_
+_
OK date
OK YEAR
OK MONTH
OK DAY
OK
+_
+_
+_
time
OK hour +_
OK minute +_
OK time forma OK
24h
12h
+_
OK first day OK susnafdtratuiyhrwdudeatradyusymnedoesansdyddaaayyy
OK
+_
sumOKmer/win OK
auto
OFF
+_
OK time zone OK europe +_
OK prague +_
OK 01 -jul- 23
Wi-Fi connection
First, make sure that you have a configuration device (PC/phone/…) with Wi-Fi
of 2.4 GHz band that supports a web browser and is close enough to SHT-13 that
you want to connect. The time switch does not support a 5 GHz band.
It is possible to connect directly to the web server for configuration via the
Wi-Fi generated by the SHT-13 (no router or internet connection required). If
the time is to be synchronized, an internet connection via a Wi-Fi router is
necessary.
Activating the Wi-Fi of time switch: After connecting the SHT-13 to the power
supply, it is possible to activate/deactivate Wi-Fi by briefly pressing the OK
button. If Wi-Fi is active and the configuration device is not connected, it
will automatically turn off after 90 seconds.
NOTE.: Wi-Fi can be activated permanently through the settings, once the setup
wizard is complete
: Now connect your configuration device to the Wi-Fi of the time switch
(follow the instructions provided by the manufacturer of the configuration
device).
SHT-13 Wi-Fi access data (default): SSID hostname: SHT-13_barcode number
Password: elkoep13
After the connection is established, the Wi-Fi symbol starts flashing on the
display.
Open the web browser of the configuration device and enter the IP address in
the address bar: 192.168.1.1
01 -jul- 23 OK 01 -jul- 23
active Wi-Fi is indicated by an icon on the display
– long press (>1s) – short press (<1s)
– long press (>1s) – short press (<1s)
20
Date and time setting
01 -jul- 23 PRG OPERATION + _ OPTIONS
OK DATE/time OK date
OK
setting the date +_
YEAR
+_ setting the year
OK
MONTH
+_ setting the month
OK
DAY
+_ setting the day
OK
date
time
OK
setting the time +_
hour
+_ setting the hours
OK
minute
OK
+_ setting the minutes
time
time forma OK
time format +_
24h 12h
+_ select format
OK
time forma
date forma OK
dd-mm-yy dd mm yy
OK
date forma
dd /mm /yy
date format +_
+_ select format
OK first day
setting the
first day of
+
the week _
susnafdtratuiyhrwdudeatradyusymnedoesansdyddaaayyy
+_ select the day
OK first day
summer/win OK
auto OFF
OK
summer/win
summer/winter time switching +_
+_
AUTO: automatically according to selected time zone
OFF: permanently deactivated
time zone OK
europe
OK
prague
OK
time zone
Astro settings
01 -jul- 23 PRG
setting the time zone
+_ select region
ASTRO MODES: F (the output of the selected
channel closes at sunset and opens at sunrise) (the output of the selected
channel opens at sunset and closes at sunrise) (the output of the selected
channel closes at sunset and sunrise) (the output of the selected
channel opens at sunset and sunrise)
ON / OFF +_
+_ select city
SUNRISE
OK SUNSET
OK
OK ASTRO mode
+_
+_
1 OPERATION
+
_
ASTRO
SETT OK ASTRO
mode OK
CHANNEL CHANNEL
+_
SUNSET-ON/
OK
SUNSET-off OK PULSE
SUSNUSNESTE-To-fOfN/
+_
+_
OK
PULSE TIME OK SUNRISE
OK SUNSET
OK ASTRO mode
+_
+_
+_
CYCLE
OK
ON TIME [
OK Off TIME
OK
START-ON START-ON
START-OFF
OK SUNRISE
OK
:
SUNSET
OK ASTRO mode
+_
+_
+_
+_
+_
+_
Location OK
COUNTRY
OK CESKA REPU OK PRAHA
OK Location
+_
+_
Coordinate OK
+_
latitude OK longitude OK Location
+_
+_
+_
Simulate
OK
1 CHANNEL
CHANNEL
+_ +_
OK YEAR +_
OK MONTH +_
OK DAY +_
OK 01 -jul- 23 OK 01 -jul- 23 ESC Simulate OK
Simulation
OK
OFF On
+_
OK Simulation
– long press (>1s) – short press (<1s) – long press (>1s) – short press (<1s)
Other settings
Delete all (programs/holidays)
2 01 -jul- 23 PRG OPERATION
OK CHANNEL CHANNEL
+_ +_
OK lorAcaSkhnTeodTRdloIOimM-dE/apyPMrTRIoO/GR OK OPERATION +_
locked set OK
2 CHANNEL
CHANNEL
+_
OK OUT off OUT oN +_
OK locked set
+_
OPTIONS
OK DATE/time
holidays OK delete all OK 01 -jul- 23 +_ PRG 01 -jul- 23 OK TIME PROGR OK
delete all OK 01 -jul- 23
To delete all time programs/holidays on a time switch simply press and hold
the buttons as shown in the pictures above and follow the options.
Location – preset locations
+_
LANGUAGE
OK SlPoOEvLSeSMPnKAAPsIGNYkYCOCyAELCRESKNKNGYNLISH
OK LANGUAGE
+_
Delete
OK OPERATING
+_
+_
2 CHANNEL
OPERATING
OK CHANNEL
OK show
OK 000000000H OK OPERATING
+_
+_
select channel
TIME CORRE OK time corre OK TIME CORRE
+_
+_
correct time (± 20 m/year)
TIME CORRECTION: Steps of 1 minute/year. The numerical value is relative to
minutes per year. The time correction is set at the factory and is individual
for each product, so that the current time clock runs with minimal deviation.
The time correction value can be changer arbitrarily, but after factory reset
the value will be set back to the factory value.
OFF
permanent
OK On
+_
OK permanent
+_
change pin OK new pin nu OK new pin nu OK pin code
+_
+_
pin code OK state
inactive OK active
OK pin code
Battery change
+_ select state
– long press (>1s) – short press (<1s)
1\. Wake up the timer from the backup mode by short press of OK button, the
main screen will
appear.
2\. Press and hold the PRG button on the main screen, use +/- to navigate to
, short press
OK, use +/- to navigate to
, short press OK to confirm, this will bring you
to the
option.
· If you are doing the replacement according to situation b., confirm the
above
option
again with the OK button. The display will show
. Time data has now been saved for
the 30 seconds during which you replace the battery, continue with step #3.
+
· If you are doing the replacement according to situation c., confirm the
above
option
again with the OK button. The display will show
. You can disconnect in the next 2
CR2032
minutes supply voltage from the mains. When the supply voltage is
disconnected, time data
are saved for 30 seconds, during which you replace the battery, continue with
step #3.
You can replace the battery in a user-friendly way, without disassembling the
device, with the mains voltage on or off. When replacing the battery, note
that terminal A2, 26, 25, 28 may be under voltage.
When replacing the battery, the following three situations may occur: a. The
timer is connected to the mains supply = proceed according to steps #3 6. b.
The timer is not connected to the mains supply (battery supply) = proceed
according to steps #1 6 c. The timer is connected to the mains supply with a
discharged battery = proceed according to steps #2 – 6
NOTE: It is good to physically insert a new battery when the 30 second
replacement interval is running out, in order to minimize the deviation of the
set time.
3\. slide out the plug-in module with the battery 4. remove the original
battery 5. insert the new battery so that the upper edge of the battery (+) is
aligned with the plug-in
module 6. insert the plug-in module as far as it will go into the device – pay
attention to the polarity (+
up)
If you did it right, the battery symbol on the display will go out after the
replacement (if the battery is fully charged) and there will be no or only a
minimal deviation in the time data. To achieve repeated and long-term running
accuracy, use time synchronization via a Wi-Fi connection – see the Wi-Fi
connection section.
Time program/holiday setting
01 -jul- 23 PRG OPERATION + _ TIME PROGR OK ADD
* Setting dashes (“–” or “—-“) instead
of a numeric value will ensure
that the given program repeats
every year, month, day or every full
hour, minute, except for the cyclic
output type.
+_
EDIT
+_
OK program
OK
2 CHANNEL
CHANNEL
OK daily
+_ +_
OK
cycle out o n
+_
OK ON TIME [
OK Off TIME
START-ON
OK
START-ON
START-OFF
OK hour
+_
OK minute +_
OK ADD
weekly
OK
OK
OK program +_
weekly
OK Delete
OK
weekly +_
OK pulse out on
+_
OK PULSE TIME OK hour
+_
+_
setting the hours *
OK minute +_
OK iniiannaacaaccatcctatcittaicitviicvtviaevvteievceeivaetvecietvieve +_
setting the minutes *
OK ADD
yearly
OK
out on
out off
+_
OK YEAR +_
setting the year *
OK MONTH
OK DAY
+_ setting the month *
+_ setting the day *
OK hour
OK minute
OK ADD
+_ setting the hours *
+_ setting the minutes *
Delete
OK program
+_ select program **
: 01 -jul- 23 PRG OPERATION
\+ _ HOliday se OK ADD
**By shortly pressing OK , you can tog-
gle between the program number
and the display of its settings. Use
\+ _ to toggle preset programs. By
holding OK you can proceed with
the required step –
. If you do not want to proceed,
press ESC to go to the main screen
without any change. Alternatively,
it will happen automatically after
90 seconds from the last button
press. If the program memory is
full, you will see
on
the display.
If the programs memory is empty and you want to change or erase a program, the
display will show
+_ EDIT
+_ Delete
OUT off
OUT off
OK holiday
OK CHANNEL
OUT oN OK
inactive
OK CHANNEL +_
OUT oN OK
inactive
OK YEAR
+_
+_
OK MONTH +_
OK DAY +_
OK hour +_
OK minute
OK
+_
start
+_ end
OK
OK
OK holiday +_
YEAR
OK MONTH
OK DAY
OK hour
OK minute
OK
+_
+_
+_
+_
+_
start OK
+_ end
OK holiday +_
OK Delete
ADD
– long press (>1s) – short press (<1s)
Firmware update / factory reset / restart
01 /jul/ 23
updating
SHT – 13/2
ENGLISH
· Firmware update: The web interface itself will guide you through the update process. After connecting to Wi-Fi SHT-13 and opening the configurator in the browser, go to the Service menu, select the file with the new firmware and click the update button.
The hidden RESET button has two functions depending on the length of the press:
Auto
01 -jul- 23
SHT-13 programming example
SHT – 13/2 SHT-13/2
Auto
ENGLISH SHT-13/2
· Factory reset: It is performed by long pressing <5 with a blunt tip of the
hidden RESET button (e.g. a pen or a screwdriver with a diameter of max. 2
mm). The display briefly shows all display segments, then the device type and
firmware version. The following is a setup guide – i.e. the same state in
which you received the timer from the factory. Settings and all configured
programs/holidays are erased by this step.
· Restart: It is done by briefly pressing <1 with the blunt tip of the hidden
RESET button. The display briefly shows all display segments, then the device
type and firmware version. This is followed by a transition to the main screen
– date, time, program activity, contact status, etc. This step will not result
in the loss of settings or configured programs/holidays.
Setting 1st channel to switch ON from the sunset to the sunrise with an offset
(deviation) of +20 minutes for the sunrise and -10 minutes for the sunset with
turning OFF from 11 p.m. to 3 a.m. every MONDAY FRIDAY.
01 -jul- 23 PRG OPERATION OK CHANNEL
OK TIME PROGR + _ ASTRO / TI OK OPERATION + _ ASTRO SETT OK ASTRO mode OK
CHANNEL
OK SUNSET-ON/ OK ON / OFF
OK SUNRISE
OK SUNset
OK ASTRO mode ESC
ASTRO
\+ SETT
_
TIME PROGR
OK
ADD
program
OK CHANNEL
OK daily
OK program
OK CHANNEL
OK daily
+_ weekly
OK out on
\+ _ out off
OK hour +_
OK minute +_
active
OK
active
active
inianacactcatitcivitvevieeve
OK ADD
+_ weekly
OK out on
OK hour +_
OK minute +_
active
OK
active inianacactcatitcivitvevieeve
OK ADD
ESC 01 -jul- 23
OK – long press (>1s) – short press (<1s)
## Read User Manual Online (PDF format)
[Read User Manual Online (PDF format) >>](/pdf/418453-elko-ep)
## Download This Manual (PDF format)
[Download this manual >>](https://manuals.plus/m/32c0c6133ab0b7d2651584ab64bbe62a0879a7e090fb14856f427b33251f0391_optim.pdf)