Metra 1995-2006 Hyundai InDash Mount Instruction Manual

Metra 1995-2006 Hyundai InDash Mount

KIT FEATURES

• DIN radio with pocket provision
• ISO mount radio with pocket provision

KIT COMPONENTS

• A) Radio housing
• B) Spacer 1L and 1R
• C) Spacer 2L and 2R
• D) Spacer 3L and 3R
• E) Spacer 4L and 4R
• F) (4) #10 x 3/4” Phillips truss head screws

WIRING & ANTENNA CONNECTIONS

(sold separately) Wiring Harness:

• 70-7300 – Hyundai wiring harness for select 1992-up
• 70-7301 – Hyundai wiring harness for select 1999-up
• 70-2003 – GMC wiring harness for select 1998-up Antenna Adapter:
• 40-GM10 (select vehicles)

TOOLS REQUIRED

• Panel removal tool
• Phillips screwdriver

CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the aftermarket radio.

Hyundai Elantra (DDIN) 1996-2000

1. Pop out the dimmer switch panel and remove (1) Phillips crew exposed. Unsnap the gear shifter trim plate and remove (1) Phillips screw exposed at the base of the dash trim bezel. Reach under the driver’s side dash, locate the temperature control cable and remove the cable from the white plastic bracket. Position the gear shifter in low, pull the dash panel away and disconnect all wiring harnesses. Remove the trim bezel (the temperature controllable will be attached). Remove (4) Phillips screws securing the factory head unit and disconnect the wiring. (Figure A)
2. Attach spacer 1L and 2L to the left mounting tabs of the radio housing and spacer 1R and 2R to the right mounting tabs of the radio housing as shown.
   (Figure B)

Hyundai Santa Fe 2001-2006

1. Remove ashtray and (2) Phillips screws exposed in cavity. Unsnap and remove climate controls with caution. The climate controls have (2) clips that connect with the radio bezel. Remove (2) Phillips screws now exposed under radio bezel (facing up). Unsnap the bottom of the radio bezel, then the top and pull straight back. Remove (4) Phillips screws and remove pocket from bezel. Remove (4) Phillips screws to remove radio from dash. (Figure A)
2. Attach spacer 3L and 4L to the left mounting tabs of the radio housing and spacer 3R and 4R to the right mounting tabs of the radio housing as shown.
   (Figure B)

Note: In cars with factory single DIN radio and pocket, you may have to file the inside edge of the factory bezel. Continue to kit assembly

Hyundai Sonata (DDIN) 1995-1998

1. Unclip the gear shifter trim panel and remove (1) screw exposed. Unclip the dash trim bezel and remove. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring. Cut and remove tabs “A” located in the top corners of the dash cavity. (Figure A)
2. Locate the radio housing. (Figure B) Continue to kit assembly

Hyundai Sonata 1999-2001

1. Detach the cable located under the left side of the glove box. Unclip the trim piece in front of the gear shifter and remove (2) Phillips screws exposed. Unclip the gear shifter trim and remove (2) Phillips screws exposed. Unclip the radio trim bezel and remove. Remove (6) Phillips screws securing the factory head unit and disconnect the wiring. (Figure A)
2. Attach spacer 3L and 4L to the left mounting tabs of the radio housing and spacer 3R and 4R to the right mounting tabs of the radio housing as shown. (Figure B)

Hyundai Tiburon (DDIN) 1997-2002

1. Remove (4) Phillips screws securing the center console. Pry out on the front edge of the console and unclip the radio trim bezel. Remove (2) Phillips screws securing the factory pocket and remove. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring. (Figure A)
2. Attach spacer 3L and 4L to the left mounting tabs of the radio housing and spacer 3R and 4R to the right mounting tabs of the radio housing as shown. (Figure B)

All Vehicles

1. Slide the DIN cage into the kit and secure by bending the metal locking tabs down.
2. Slide the aftermarket head unit into the cage until secure.
3. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation.
4. Reassemble dash in reverse order of disassembly.

METRA. THE WORLD’S BEST KITS.™
TEL: 1-800-221-0932
metraonline.com
COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION

References

• Installer Institute Announces Closure after 31 Years | installerinstitute.edu

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>