elko ep RFRP-20 Key Fob 6 Buttons Color Black User Manual

: June 13, 2024
: ELKO ep

Table of Contents

elko ep RFRP-20 Key Fob 6 Buttons Color Black
Characteristics
Indicators, settings
Insertion and replacement of a battery
Technical parameters
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

elko ep RFRP-20 Key Fob 6 Buttons Color Black

EAN: 8595188180740
EAN: 8595188180757
EAN: 8595188180764
EAN: 8595188180771

NEW WAY OF PROGRAMMING! = pairing with Inels RF Control receivers

Characteristics

Key fob-sized remote control, available in black and white.
When the button is pressed, it sends the set command (ON / OFF, dimming, time on / off, lower / raise).
RF KEY-40: 4 buttons, each of which allows you to control an unlimited number of components.
RF KEY-60: 6 buttons, each of which allows you to control an unlimited number of components.
Replaceable battery (3 V CR 2032) with a service life of approx. 5 years (depending on the frequency of use).

Indicators, settings

Newly produced drivers work in the RFIO2 data protocol mode. These drivers are loaded in the actuators in a different way than before. Among other things, it eliminates the risk of inadvertently loading another randomly occurring controller within range. Drivers can still be switched to so-called compatibility mode, and loaded in a simpler (older way).
The mode in which the controllers are working is changed and indicated after 8 seconds by pressing the ‘Prog’ button. The LED diode under the pushbutton is on when the button is kept pressed; after 8 seconds it indicates the chosen mode by different flashing intervals. The mode changes to the inverse mode after each pressing of the button.

RFIO2 mode = Double flash (flash, flash, gap, flash, flash)
Compatibility mode = Flash fast (flash, flash, flash, flash, flash)

Update the controller actuators in RFIO2 mode
If the controller is used in RFIO2 mode, then to update the controller actuators, it is necessary to switch not only the actuator to the update mode (according to the instructions for the actuator), but also the controller in the following way:

Press the programming button on the controller, and converter for more than 1 second and release it.
The LED diode starts ﬂashing in second intervals. Leave the LED ﬂ ashing
to activate the programming mode on the actuator by pressing the programming button for more than 1 second. The actuator is also put into the programming mode.
The desired function can be selected by the respective number of presses of the control pushbuttons or inputs (of the converter).
The programming modes on the controller and actuator can be closed by pressing the programming button for less than 1 second. The LEDs stop ﬂashing.

Radiofrequency signal penetration through various construction materials

elko-ep-RFRP-20-Key-Fob-6-Buttons-Color-Black-fig-2

Insertion and replacement of a battery

Using a Phillips head screwdriver, remove the screw on the back of the transmitter. Remove the rear cover.
Slide the CR2032 battery into the battery holder. Observe the polarity.
Replace the rear cover and replace the screw.

Technical parameters

elko-ep-RFRP-20-Key-Fob-6-Buttons-Color-Black-fig-6

Attention:
When you install the iNELS RF Control system, you have to keep a minimal distance of 1 cm between each unit. Between the individual commands must be an interval of at least 1s.

Safe handling

When handling a device unboxed it is important to avoid contact with liquids. Never place the device on the conductive pads or objects, avoid unnecessary contact with the components of the device.

Warning

The instruction manual is designated for mounting and also for the user of the device. It is always a part of its packing. Installation and connection can be carried out only by a person with adequate professional qualifications upon understanding this instruction manual and the functions of the device, and while observing all valid regulations. The trouble-free function of the device also depends on transportation, storage, and handling. In case you notice any sign of damage, deformation, malfunction or missing part, do not install this device and return it to its seller. It is necessary to treat this product and its parts as electronic waste after its lifetime is terminated. Before starting installation, make sure that all wires, connected parts or terminals are de-energized. While mounting and servicing observe safety regulations, norms, directives, and professional, and export regulations for working with electrical devices. Do not touch parts of the device that are energized – life threat. Due to the transmissivity of RF signal, observe correct location of RF components in the building where the installation is taking place. RF Control is designated only for mounting in interiors. Devices are not designated for installation in exteriors and humid spaces. They must not be installed into metal switchboards and into plastic switchboards with metal doors – transmissivity of RF signal is then impossible. RF Control is not recommended for pulleys etc. – radiofrequency signal can be shielded by an obstruction, interfered, battery of the transceiver can get fl at, etc., and thus disable remote control.

ELKO EP declares that the RF KEY type of radio equipment complies with Directive 2014/53 / EU. The full EU Declaration of Conformity is available at:

ELKO EP, s.r.o., Palackého 493, 769 01 Holešov, Všetuly, Czech Republic Tel.: +420 573 514 211, e-mail: elko@elkoep.com, www.elkoep.com