Dyson HP01 Pure Hot + Cool Purifier Heater User Manual
- June 12, 2024
- dyson
Table of Contents
Dyson HP01 Pure Hot + Cool Purifier Heater User Manual
ASSEMBLY
REGISTER TODAY
3 easy ways to register your 2-year limited warranty.
I MPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL MACHINES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PERSONS INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
WARNING
THE MACHINE AND THE REMOTE CONTROL BOTH CONTAIN MAGNETS.
-
Pacemakers and defibrillators may be affected by strong magnetic fields. If you or someone in your household has a pacemaker or defibrillator, avoid placing the remote control in a pocket or near to the device.
-
Credit cards and electronic storage media may also be affected by magnets and should be kept away from the remote control and the top of the machine.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY: -
This Dyson machine is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction by a responsible person concerning the use of the machine to ensure that they can use it safely.
-
Do not allow it to be used as a toy. Close attention is necessary when used by or near children. Children should be supervised to ensure that they do not play with the machine.
-
Always plug this machine directly into a wall outlet/receptacle. Never use an extension cord or relocatable power tap (outlet/power strip).
-
This machine must not be located immediately below a socket outlet.
-
If there is a loose fit between the plug and the outlet or the plug becomes very hot, the outlet may need to be replaced. Check with a qualified electrician to replace the outlet.
-
CAUTION – Risk of electric shock, do not open the machine, and no user-serviceable parts inside.
-
This machine is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. When moving the machine, hold it by the base and not the air loop amplifier. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the machine and keep them away from the sides and rear.
-
This machine has hot parts inside. Do not use it in areas where petrol, paint, or flammable liquids are used or stored or where their vapors are present.
-
Extreme caution is necessary when any machine is used by or near children or infirm persons and whenever it is left operating and unattended.
-
Do not operate any machine with a damaged cord or plug or after the machine malfunctions, or has been dropped or damaged in any manner. Discard the machine, or return it to an authorized service facility for examination and/or repair.
-
Do not run the cord under the carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not route the cord under furniture or machines. Arrange the cord away from traffic areas and where it will not be tripped over.
-
To avoid a tripping hazard, wind the cord when not in use.
-
This machine is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never locate the machine where it may fall into a bathtub or other water containers. Do not store this machine in the immediate surroundings of a bath, shower, or swimming pool.
-
WARNING : In order to avoid overheating, do not cover the machine.
-
To prevent a possible fire, do not block air intakes or exhausts in any manner. Do not use it on soft surfaces, like a bed, where openings may become blocked.
-
Use this machine only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
-
Do not use this machine if it has been dropped or if it has visible signs of damage.
-
Always use this appliance on a horizontal and stable surface.
-
Do not use it outdoors or on wet surfaces and do not handle any part of the machine or plug with wet hands.
-
Keep this machine and cord away from heated surfaces. Do not position the cord under the furniture or machines.
-
If the supply cord is damaged, it must be replaced or repaired by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
-
Do not use this machine if it has been damaged or submerged in water.
-
Do not put any objects into any opening as this may cause an electric shock or fire, or may damage the machine.
-
Disconnect power or unplug before cleaning, performing any maintenance or replacing a filter. Always unplug the machine when not in use.
-
Chemical Burn and Choking Hazard. Keep batteries away from children. This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Even used batteries may cause injury. POLARIZATION INSTRUCTIONS
-
To reduce the risk of electric shock, this machine has a polarized plug (one blade is wider than the other) as a safety feature. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not attempt to defeat this safety feature and do not change the plug in any way.
SAVE THESE INSTRUCTIONS
Power
- Each time the heating mode is selected, it conducts a short calibration cycle. Airflow will be automatically controlled during this cycle. Once the calibration cycle is complete, it will revert to the selected airflow speed. On first use, the machine will default to a temperature 3°C higher than the detected room temperature.
- Thereafter, the machine will remember the last target temperature set.
- Select the desired room temperature using the Thermostat control button. Press the large red button on the remote control to increase the target temperature by 1°C; press the small red button on the remote control to decrease it by 1°C. The machine will not operate in heating mode unless the target temperature is above room temperature.
Remote control
Remote control docks magnetically
Attach the remote control to the top of the machine with the buttons facing
down.
Airflow speed control
Press the red Thermostat control button until the digital display shows the
target room temperature. The power button light will change from blue to red
to indicate that you have entered the heating mode. The heating symbol will be
red while heating and will change to white when the target room temperature
has been reached. Once the target room temperature has been reached, the
machine will stop heating the air. If the room temperature falls below the
target temperature, the machine will start to heat again. The red circle
surrounding the power button remains on when the machine is in heating mode.
To adjust the airflow speed, use the airflow control button.
Press the blue Cooling mode button to enter cooling mode. The power button light will change from red to blue to indicate that you have entered the cooling mode. To adjust the airflow speed, use the airflow control button.
Sleep timer
Tilt function
- To set the sleep timer, select the desired time. When the time reaches zero, the machine will go into standby mode. To cancel, increase the time until two dashes appear.
- When using the sleep timer, the LED display will turn off after 10 seconds of inactivity.
- Carefully hold the base and the main body. Tilt the loop amplifier forward or backward for the required airflow angle.
Diffused and Focused modes
Diffused mode
Press the wide-angle button to change from a personally directed airflow to a
whole room airflow. Heating and cooling modes work in this mode.
Oscillation and Airflow speed control
Oscillation control
To start the machine oscillating, Press the Oscillation control button. To
stop the machine from oscillating, press it again. The machine will not
oscillate when the control buttons are pressed
Focused mode
Press the narrow-angle button to change from a whole room airflow to a
personally directed airflow. Heating and cooling modes work in this mode.
Airflow speed control
To change the airflow speed, press the Airflow speed control button. The
digital display will show the new fan speed. If in heating mode, after 3
seconds it will change back to displaying the target temperature
Cleaning
Unplug from the main power source. If the machine has been in use, leave it for 1 to 2 hours before cleaning to allow the machine to cool completely. Dust may accumulate on the surface of the machine. Wipe dust from the loop amplifier, filter unit, and other parts with a dry or damp cloth when dust accumulates. Do not use detergents or polishes.
Clearing blockages
Unplug from the main power source. If the machine has been in use, leave it
for 1 to 2 hours in order to allow the machine to cool down completely. Look
for blockages in the air inlet holes and in the small aperture inside the air
loop amplifier. Use a soft brush to remove debris.
Caution: Hot when in use
This machine is hot when in use and for a short period after use. Do not let
bare skin touch hot surfaces. If children are present, consider positioning
the machine out of their reach.
Battery replacement
Unscrew the battery compartment on the remote control. Loosen the base and
pull to remove the battery.
Replacing the filter unit
When your non-washable filter unit needs replacing the machine will display the pattern shown. To replace the non-washable filter unit, follow these steps. If the machine has been in use, leave it for 1 to 2 hours before replacing the filter unit to allow the machine to cool down completely. Your Dyson machine is programmed to remind you to replace the filter unit after 12 months based on 12 hours of usage a day. Please note that your indicator will activate sooner with more use. The indicator is only a guide. Use in heavily polluted environments may require the filter unit to be replaced more regularly.
When you have reassembled your machine, press and hold the Standby on/off button for 6 seconds on the remote control to reset the filter indicator.
USING YOUR DYSON MACHINE
PLEASE READ THE ‘IMPORTANT SAFETY INSTRUCTIONS’ IN YOUR DYSON USER MANUAL
BEFORE PROCEEDING. LOOKING AFTER YOUR DYSON MACHINE
- Do not carry out any maintenance or repair work other than that shown and described in your Dyson User manual, or advised by the Dyson Helpline.
- Always disconnect the plug from the mains outlet before inspecting for problems. If the machine will not operate, first check that the mains outlet has an electricity supply and that the plug is properly inserted into the outlet.
- If the fuse needs replacing, please check ‘User servicing instructions’.
OPERATION
- Ensure that the machine is fully assembled in line with the instructions before use.
- Do not dismantle the machine or use it without the loop amplifier fitted.
- The machine will not operate in heating mode unless the target temperature is above room temperature.
- Each time the heating mode is selected, it conducts a short calibration cycle. Airflow will be automatically controlled during this cycle. Once the calibration cycle is complete, it will revert to the selected airflow speed.
- The machine will not oscillate when the control buttons are pressed.
- Do not lubricate any part of this machine.
CONTROL WITHOUT REMOTE
- Press the power button on the machine to turn on/off.
- Press and hold the power button on the machine to adjust the target temperature.
- The target temperature will increase to a maximum before decreasing. If the target temperature is set at 0°C it will switch from heating to cooling mode.
- The airflow, diffused and personal heating modes, oscillation function, and sleep timer controls cannot be operated without the remote control.
LED DISPLAY
- The LED display will dim after 10 seconds of use.
- Press any button, other than the Standby ON/OFF, to reactivate.
- Do not press Standby ON/Off as this will turn the machine off.
SLEEP TIMER
To set the sleep timer, press and hold the Sleep timer button to select the
desired time. When the time reaches zero, the machine will go into standby
mode. To cancel, reduce the time until two dashes appear.
- The LED display will turn off after 10 seconds of inactivity – this is a power-saving feature and avoids light interference at night time.
- Press any button, other than the Standby ON/OFF, to reactivate.
- When the sleep timer is ON, do not press the Standby ON/OFF as this will turn the machine off and turn the sleep timer off too.
TILT FUNCTION
Carefully hold the base and the main body. Tilt the loop amplifier forward or
backward for the required airflow angle.
AUTOMATIC CUT-OUT
For your safety, this machine is fitted with automatic cut-out switches that
operate if the machine tips over or overheats. If the switches operate, unplug
the machine and allow it to cool. Before restarting the machine, check and
clear any blockages and ensure that the machine is on a solid level surface.
In heating mode, the machine will automatically switch off after 9 hours of
continuous use and will return to standby mode. To restart the machine, press
the power button on either the remote control or the base.
TROUBLESHOOTING
Fault codes F4, F5, and F6: If one of these appears on the display, unplug the
machine, wait for 30 to 60 seconds, and/or plug the machine into a different
socket. If you continue to receive the fault code, please contact the Dyson
Helpline.
Fault codes F2, F3, and F7: If one of these appears on the display, please
contact the Dyson Helpline.
REPLACEABLE PARTS BATTERY REPLACEMENT
CAUTION
- Switch off and unplug the machine before replacing the batteries.
- Unscrew the battery compartment on the remote control. Loosen the base and pull to remove the battery.
- Do not install backward or short-circuit the batteries.
- Do not attempt to dismantle or charge the batteries. Keep away from fire.
- Always replace the screw in the remote control and refer to the battery hazard in the warning section.
- Follow battery manufacturers’ instructions when installing new batteries (battery type CR 2032).
- Limited functionality is available without the remote control (see ‘Control without remote’).
NON-WASHABLE FILTER UNIT
- Your filter unit is non-washable and non-recyclable.
- To replace your filter unit follow the steps as shown.
- Failure to replace the filter when prompted may result in changes to the product
DISPOSAL INFORMATION
- Dyson products are made from high-grade recyclable materials. Recycle where possible.
- Dispose of or recycle the battery in accordance with local ordinances or regulations.
- Keep the used batteries away from children as these can still harm children if swallowed.
- Your filter units are non-washable and non-recyclable.
- Dispose of the exhausted filter units in accordance with local ordinances or regulations.
- The battery should be removed from the machine before disposal.
DYSON CUSTOMER CARE
THANK YOU FOR CHOOSING TO BUY A DYSON MACHINE.
After registering your 2-year warranty, your Dyson machine will be covered for
parts and labor (excluding filters) for 2 years from the date of purchase,
subject to the terms of the warranty. If you have any questions regarding your
Dyson machine, visit www.dyson.com.mx for online
help, general tips, and useful information about Dyson. Alternatively, you can
contact us via email or phone with your serial number and details of where and
when you bought the machine. If your Dyson machine needs a repair, email or
phone Dyson so we can discuss the available options. If your Dyson machine is
under warranty, and it is a covered repair, it will be repaired at no cost.
Your serial number can be found on your rating plate which is on the base of
your machine.
PLEASE REGISTER AS A DYSON MACHINE OWNER
To help us ensure that you receive prompt and efficient service, please
register as a Dyson machine owner.
- Online at www.dyson.com.mx/register
- Register by phone: 01 800 872 0154
- This will confirm ownership of your Dyson machine in the event of an insurance loss, and enable us to contact you if necessary.
IMPORTANT DATA PROTECTION INFORMATION
WHEN REGISTERING YOUR DYSON MACHINE:
- You will need to provide us with basic contact information to register your machine and enable us to support your warranty.
- When you register, you will have the opportunity to choose whether you would like to receive communications from us. If you opt-in to communications from Dyson, we will send you details of special offers and news of our latest innovations.
- We never sell your information to third parties and only use information that you Share with us as defined by our privacy policies which are available on our website at privacy.dyson.com
ELECTRICAL SPECIFICATIONS
CONNECTION INSTRUCTIONS
- Connect the plug on the power cord to a 127V AC power socket
- Do not unplug by pulling on the cord, firmly grasp the plug and remove it gently.
- Unplug the device from the AC power socket if you are not going to use the product for an extended period
THANK YOU FOR CHOOSING TO BUY A DYSON MACHINE
After registering your free 2-year warranty, your Dyson machine will be
covered for parts and labor (excluding filters) for 2 years from the date of
purchase, subject to the terms of the warranty. If you have any questions
about your Dyson machine, please contact Dyson Customer Care with your serial
number and details of where and when you bought the machine. Most questions
can be solved by one of our trained Dyson Customer Care staff. Your serial
number can be found on your rating plate which is on the base of the machine.
Visit www.dyson.com.mx/support for online
help, support videos, general tips, and useful information about Dyson Note
your serial number for future reference.
This illustration is, for example, purposes only.
Download PDF:Dyson HP01 Pure Hot + Cool Purifier Heater User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>