VIVO Two Frame Stainless Steel Honey Extractor Instruction Manual
- June 7, 2024
- Vivo
Table of Contents
VIVO Two Frame Stainless Steel Honey Extractor Instruction Manual
SKU: BEE-V002C
Scan the QR code with your mobile
device or follow the link for helpful videos and specifications related to
this product.
BEE-V002C
Two Frame Stainless Steel Honey Extractor
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303
WARNING : IMPORTANT SAFETY INFORMATION
READ AND FOLLOW ALL SAFETY REQUIREMENTS
KEEP THIS MANUAL IN A SAFE AND DRY PLACE FOR FUTURE REFERENCE
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
PREPARATION
- After carefully removing the machine from the packing carton, remove all protective film and clean the honey extractor thoroughly with mild soap and water BEFORE first use.
- The honey extractor should be placed on a dry, flat stable surface.
CAUTION : SHARP EDGES
MACHINE STRUCTURE
PACKAGE CONTENTS
WARNING: SHARP EDGES!
Please be cautious of sharp edges inside the drum. Assemble and operate
extractor with care. Failure to proceed with caution could result in personal
injury.
ASSEMBLY STEPS
STEP 1
After carefully removing the machine from the packing carton, clean the honey
extractor thoroughly with mild soap and water BEFORE first use. The extractor
should be placed on a dry, flat stable surface.
STEP 2
Press the crank handle (2) onto the square shaft, then tighten the bolt on the
side of the handle to secure. Tighten the nut against the handle to prevent
the bolt from loosening over time.
STEP 3
Secure metal lid (3) with the attached steel clips.
OPERATING INSTRUCTIONS
- Place honey frames in extractor basket. Load both sides to keep extractor balanced as this will reduce any possible shaking.
- Place lid on extractor and begin turning handle to extract honey.
- Once the frames have been emptied on one side, remove the frames, turn the frames around, and place them back in the extractor. Repeat step 2, then remove the frames from the extractor.
- With the drain positioned over a bucket or other container, open the honey gate to begin draining honey. Tip the extractor forward to drain as much honey as possible.
WARNING : KEEP HANDS CLEAR OF MOVING PARTS TO REDUCE RISK OF INJURY
DISASSEMBLY
To fully disassemble the extractor, first loosen the large gear from the crank shaft by loosening the bolt on the side of the gear. Remove crank shaft by pulling out through the side. You may need to grip the shaft with pliers while prying it forward if it does not slide out freely. Remove the gear as soon as the shaft has been pulled out enough to do so, as it may otherwise fall into the bottom of the extractor. Remove the four bolts near the top of the extractor, then pull the top brace out of the drum. The basket will lift out with the brace.
CARE & MAINTENANCE
QUICK CLEANING
Option 1 : Rinse extractor out with cold water from a hose. If available, a pressure washer is very effective. Empty excess water to prevent possible surface rust.
Option 2 : Place open extractor next to hive. Bees will clean it out and use the materials.
IN-DEPTH CLEANING
Disassemble extractor (see Disassembly instructions). Using mild dish soap and warm water, scrub drum and basket clean. Completely rinse the parts and dry with a soft cloth. Reassemble the extractor when dry.
CARE
- When not in use, store the extractor in a dry place. Although stainless steel is highly resistant to rust and corrosion, light surface rust can form in wet conditions.
- If surface rust forms, clean with a light abrasive to remove rust.
- If the extractor begins making squeaking noises, lightly lubricate all bearings with a food safe grease or oil. Wipe away any excess.
- If the roller bearing in the crank shaft support block does not turn freely, lubricate with a light grease (such as white lithium) or oil.
- The gearbox is permanently sealed and requires no maintenance.
WARRANTY
We offer a ONE YEAR warranty for this product. If you have any problems with the machine, please contact us directly. We have a 30 Day Return Policy.
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
LAST UPDATED: 02/02/2021 REV2
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- BEE-V002C Two Frame Stainless Steel Honey Extractor – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>