LAKELAND Raclette Cheese Melter

LAKELAND Raclette Cheese Melter

PRODUCT FEATURES

1. Cheese grill
2. Heating element
3. Cheese holder
4. Handles
5. Slider
6. Base unit
7. Non-slip feet
8. Removable slider track
9. On/off switch
10. Power cable and plug

SAFETY CAUTIONS

Carefully read all the instructions before using the appliance and keep in a safe place for future reference. Always follow these safety cautions when using the appliance to avoid personal injury or damage to the appliance. This appliance should be used only as described in this instruction book.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children unless they are older than 8 and supervised.

• Make sure your electricity supply matches the voltage shown on the appliance.
• Ensure all packaging materials and any promotional labels or stickers are removed from the appliance before the first use.
• Always inspect the appliance before use for noticeable signs of damage. Do not use if damaged or has been dropped. In the event of damage, or if the appliance develops a fault contact the Lakeland customer care team on 015394 88100.
• Do not use this appliance if the lead is damaged. If the lead is damaged it must be replaced, contact the Lakeland customer care team on 015394 88100.
• Always use the appliance on a dry, level, heat resistant surface.
• Unplug from the mains when not in use and before cleaning. To disconnect, turn the socket to “off” and remove the plug from the mains socket.
• Do not use any accessories or attachments with this appliance other than those recommended by Lakeland.
• To protect against fire, electric shock or personal injury, do not immerse cord, plug or unit in water or other liquids.
• Do not leave the lead hanging over the edge of a kitchen table or worktop. Avoid contact between the lead and hot surfaces.
• For indoor use only.
• For domestic use only. It is not suitable for commercial use, or for use outdoors.
• This appliance should be used for preparation of food as described within the instructions for use that accompany it.
• Always ensure that your hands are dry before removing the plug from the mains socket. Never pull the plug out of the mains socket by its lead.
• To avoid injury or possible fire, do not cover the appliance when in use.
• Do not connect this appliance to an external timer or remote control system.
• An earthed extension cable may be used with care. The electrical rating of the cable should be at least as great as the appliance. Do not allow the cable to hang over the edge of the worktop or touch any hot surfaces.
• This appliance complies with the basic requirements of Directives 2014/30/EU (Electromagnetic Compatibility) and 2014/35/EU (Low Voltage Directive).

WARNING : A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure the cut off plug is disposed of safely
CAUTION : The plastic bags used to wrap this appliance, or the packaging may be dangerous. To avoid risk of suffocation, keep these bags out of reach of babies and children. These bags are not toys.

• Keep the Cheese Melter, plug and lead away from hot ovens, electric and gas burners, flames and hot surfaces.
• The appliance should only be used in a well ventilated area, at least 30cm away from walls and other surfaces to allow sufficient airflow.
• Do not use the Cheese Melter unless it is fully assembled.
• Do not leave appliance unattended whilst switched on.
• Do not attempt to move this appliance when it is still hot. Cool completely before moving.
• Do not touch the heating element with utensils.
• Switch off and unplug the appliance from the socket before cleaning and when not in use. Always allow the appliance to cool down completely before cleaning.

WARNING – HOT SURFACES

The surfaces marked with this symbol will get very hot during use and will stay hot after use.
Do not allow the power cord to hang over the edge of a counter where it may be grabbed by children or become entangled with the user.
To prevent injury, DO NOT TOUCH.
The temperature of accessible surfaces may be high when the appliance is in operation.
To avoid burns, please use oven gloves to move the handle parts under the heating element when in use.

SETTING UP THE RACLETTE CHEESE MELTER AND USING FOR THE FIRST TIME

1. Unpack the Cheese Melter. Remove all the packaging materials.
   WARNING: Do not plug in the appliance until it is fully assembled and installed on the base unit. Only plug in when the appliance is fully assembled and ready to use.

2. Wipe the metal outer surfaces of the appliance with a clean damp cloth and dry before first use.

3. Wash the cheese holder in warm soapy water and dry thoroughly.

ASSEMBLY OF THE CHEESE MELTER

1.  Make sure the slider track is secure and the nuts are tight underneath the base plate.
2. Attach the cheese grill to the base unit, by sliding the connector over the bracket on the base unit. Secure in place with the black headed screw.
3. Attach the cheese holder to the slider using the screw.
4. Now slot the slider into the slider track, this should now be stable and be able to move freely backwards and forwards along the slider track and rotate round. Your Cheese Melter is now ready to use.

INSTRUCTIONS FOR USE

WARNING: Do not leave the Cheese Melter unattended when it is switched on.
CAUTION: The metal surfaces of the appliance become hot during use. Do not touch the appliance while it is in use.

When you switch on the appliance for the first time there may be a slight burning smell. This is normal for a new product and will disappear after a few uses. We advise heating up the Cheese Melter empty on first use for about 10 minutes. Ventilate the room during this period.

PLACING THE RACLETTE CHEESE ON THE HOLDER

• To secure raclette cheese onto the cheese holder, place the cheese on a clean, flat surface.
• Lift the cheese holder off the slider and insert all 4 prongs into the outer edge of the cheese rind so that the exposed side(s) of the cheese will sit parallel to the heat.
• Insert the holder with cheese back onto the slider on the base.
• Switch on the appliance using the On/Off switch at the back of the appliance.
• Cheese takes approximately 15 minutes under the heat before the first portion is ready to serve. Small wedges of cheese will take longer as they will sit further away from the heat. If you want the cheese to melt quicker, hold the cheese on the cheese holder up to the heat/heating element using the handles. Keep hands away from the heat.
• The Cheese Melter works best with either a small half wheel or large wedge of raclette cheese with rind so the cheese sits closer to the heat.
• Place a small plate on the base unit at the bottom of the melting cheese to catch drips whilst melting.

HINTS AND TIPS

• We recommend only using raclette cheese.
• The Cheese Melter works best with either a small half wheel or large wedge of raclette cheese with rind so the cheese sits closer to the heat, and the rind helps to secure the cheese on the holder.

FREQUENTLY ASKED QUESTIONS

Question: Why is the Cheese Melter not working?
Answer: Check that the plug is turned on at the wall socket.

Question: Why is the cheese not melting?
Answer: The raclette cheese on the cheese holder may be too small to gain enough heat from the heating element. Lift the cheese holder by the handles and carefully hold closer to the heating element. Keep your hands away from the heating element as this is very hot, use oven gloves to protect yourself.

Question: Why is the cheese slider not moving freely?
Answer: There may be dirt and build up of cheese in the slider track. Once cooled down, remove the slider track and clean. To help prevent build-up of cheese, place a small plate at the bottom of the melting cheese to catch drips.

CARE AND CLEANING

• Switch off and unplug the Cheese Melter from the socket before cleaning and when not in use. Always allow the Cheese Melter to cool down completely before cleaning.
• Before the first use and after every use, clean each part thoroughly.
• Never immerse the cheese grill, cord or plug in water or any other liquid. To clean, wipe with a clean damp cloth and dry before storing.
• The base unit, slider track and cheese holder are removable. Wash in warm soapy water and dry thoroughly.
• Check all parts before reassembling.
• Do not use scouring pads, steel wool, or abrasive cleaners, or materials. Fragments of metal could come loose and touch the appliance’s electrical parts causing it to short circuit.
• Store the Cheese Melter with the power cable loosely coiled. Never wrap it tightly around the product.

TECHNICAL INFORMATION

• Power: 400W.
• Voltage: 230V~
• Frequency: 50-60Hz.

ELECTRICAL CONNECTIONS

THIS APPLIANCE MUST BE EARTHED

The appliance is fitted with a fused three-pin plug to BS1363 which is suitable for use in all homes fitted with sockets to current specifications.

CHANGING THE 5 AMP FUSE

Use a 5 amp BS1362 fuse. Only BSI or ASTA approved fuses should be used. If you are unsure which plug or fuse to use, always refer to a qualified electrician.
Note: After replacing or changing a fuse on a moulded plug which has a fuse cover, the cover must be refitted to the plug; the appliance must not be used without a fuse cover. If lost, replacement fuse covers can be obtained from an electrical shop. This appliance complies with the following EU Directives: 2014/35/EU (Low Voltage Directive) and 2014/30/EU (EMC Directive).

RECYCLING YOUR ELECTRICALS

Along with many other high street retailers, Lakeland has joined a scheme whereby customers can take their unwanted electrical product to recycling points set up around the country. Visit www.recycle-more.co.uk to find your nearest recycling point.

References

• Everything you need to know to Recycle More

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>