ejendals 6 Pairs Tegera 8830R Instruction Manual
- June 3, 2024
- ejendals
Table of Contents
TEGERA® 8830R
Instruction Manual
INSTRUCTIONS FOR USE
PRODUCT SPECIFIC INFORMATION ONLY ON THIS PAGE
Cut resistant glove, winter-lined, nitrile foam, palm-dipped, foam grip pattern, cut resistance level D, 10 gg, acrylic, CRF® Technology, nylon, polyester, stainless steel fibre yarn, Cat. II, black, blue, withstands contact heat up to 250°C, pair packed, for allround work
| EN ISO 21420:2020
EN 388:2016+A1:2018 4X42D
---|---
| EN 407:2020 No Flame Protection
X2XXXX
| EN 511:2006 01X
| Contact heat rating valid for palm area only
INSTRUCTIONS FOR USE – CATEGORY II
SEE FRONT PAGE FOR PRODUCT SPECIFIC INFORMATION
OUTER MATERIAL SPECIFICATION Nitrile
INNER MATERIAL SPECIFICATION Acrylic, HPPE, stainless steel fibre yarn,
polyester, nylon
SIZE RANGE (EU) 7,8,9,10,11,12
EU-TYPE EXAMINATION 2777 Satra Technology Europe Ltd Bracetown Business
Park, Clonee, Dublin 15, Dublin, Ireland
UKCA-TYPE EXAMINATION
0321 SATRA Technology Centre, Wyndham Way, Telford Way, Kettering,
Northamptonshire, NN16 8SD, United Kingdom
INSTRUCTIONS FOR USE – CATEGORY II
SEE FRONT PAGE FOR PRODUCT SPECIFIC INFORMATION
DECLARATION OF CONFORMITY
www.ejendals.com/conformity
Carefully read these instructions before using this product.
EXPLANATION OF PICTOGRAMS 0 = Below the minimum performance level for the
given individual hazard X= Not submitted to the test or test method not
suitable for the glove design or material
Warning! This product is designed to provide protection specified in PPE
Regulation (EU) 2016/425 and PPE Regulation 2016/425 as amended and brought
into UK law with the detailed levels of performance presented below. However,
always remember that no item of PPE can provide full protection and caution
must always be taken when exposed to risks.
EN 407:2020 PROTECTIVE GLOVES AGAINST THERMAL RISKS (HEAT AND/OR FIRE)
ABCDEF| A: Limited flame spread
B: Contact heat
C: Convective heat
D: Radiant heat
E: Small splashes of molten metal
F: Large quantities of molten metal
---|---
PERFORMANCE (A-F)
Min. 0; Max. 4
Warning: EN 407:2020: if the glove consists of seperate parts which are not permanently interconnected, the perfomance levels and the protection only apply to the complete assembly. If the gloves have a performance level 1, 2 or X in limited flamespread in EN 407:2020 the gloves should not come in contact with naked flame. Glove tested according to the 6.6 “small splashed of molten metal” is not suitable for welding activities. In the event of a molten metal splash the glove may not eliminate all risks of burn and the user shall leave the working place immediately and take off the glove. No flame protection
EN 388:2016 +A1:2018
ABCDEF| A. Abrasion resistance
B. Blade cut resistance
C. Tear resistance
D. Puncture resistance
E. Cut Resistance TDM (EN ISO13997),
F. Impact Protection| Min. 0; Max. 4
Min. 0; Max. 5
Min. 0; Max. 4
Min. 0; Max. 4
Min. A; Max. F P=Pass
---|---|---
PROTECTIVE GLOVES AGAINST MECHANICAL RISKS. Protection levels are measured from area of glove palm. Warning: For gloves with two or more layers the overall classification of EN 388:2016 +A1:2018 does not necessarily reflect the performance of the outmost layer. Do not use these gloves near moving elements or machinery with unprotected parts. For dulling during the cut resistance test, the coupe test results are only indicative while the TDM cut resistance test is the reference performance result.
EN 511:2006
ABC| PROPERTY
A. Convective cold
B. Contact cold
C. Water penetration| PERFORMANCE
Min. 0; Max. 4
Min. 0; Max. 4
0 (Fail); 1 (Pass)
---|---|---
Warning: EN 511:2006: if the glove consists of seperate parts which are not permanently interconnected, the perfomance levels and the protection only apply to the complete assembly. EN 511: Care must be taken when choosing the correct glove with regards to the maximum user exposure. If not water proof, the glove may lose its insulating properties if wet. EN511:2006 Annex B table B.1 shows various parameters to be considered. Studies have established certain correlations between these parameters and the level of thermal insulation required to protect in cold conditions. The table given in Annex B of EN342:2004 is an example of such data.
SUITABLE FOR CONTACT WITH FOOD SPECIFIED IN REGULATION (EU) 10/2011 AND
1935/2004.
All gloves/sleeves that are suitable for foodstuff may not be suitable for all
types of food. To know for which foodstuff the glove/sleeve may be used please
see the Food declaration of conformity. Contact Ejendals for more information.
EN ISO 21420:2020 PROTECTIVE GLOVES – GENERAL REQUIREMENTS AND TEST
METHODS Finger dexterity test: Min. 1; Max. 5
FITTING AND SIZING: All sizes comply with the EN ISO 21420:2020 for comfort,
fit and dexterity, if not explained on the front page.
If the short model symbol is shown on the front page, the glove is shorter
than a standard glove, in order to enhance the comfort for special purposes –
for example fine assembly work. Only wear the products in a suitable size.
Products which are either too loose or too tight will restrict movement and
will not provide the optimal level of protection.
STORAGE AND TRANSPORT: Ideally stored in dry and dark condition in the
original package, between +10º – +30ºC.
INSPECTION BEFORE USE: Check that the glove does not present holes, cracks,
tears, colour change etc. If the product becomes damaged it will NOT provide
the optimal protection and must be disposed of. Never use a damaged product.
Wear (or take off) gloves one at a time. Replace gloves regularly for hygienic
use
SHELF LIFE: The nature of the materials used in this product means that the
life of this product cannot be determined as it will be affected by many
factors, such as storage conditions, usage etc.
CARE AND MAINTENANCE:
The user bares sole responsibility for submitting the product to mechanical
washing after use, as unknown substances can contaminate the product during
use and may affect the performance levels of the product. To care for your
product, we recommend that you rinse in cold water and line dry in room
temperature.
DISPOSAL: According to local environmental legislations.
The glove contains natural rubber which may cause allergy.
ALLERGENS: This product may contain components that may be a potential risk to
allergic reactions. Do not use in case of hypersensitivity signs.
For more information contact Ejendals.
latex free Yes ×No
Made in China
ONLY FOR EURASIAN ECONOMIC COMMUNITY CUSTOMS UNION MEMBERS
THE PRODUCTS COMPLY WITH THE REQUIREMENTS OF TR CU 019/2011
“On SAFETY OF PERSONAL PROTECTION MEANS”.
uk-importer
Ejendals ltd, Sweden House, 5 upper Montagu Street,
London, England, W1 2AG
ejendals ab
Limavägen 28, SE-793 32 Leksand, Sweden
info@ejendals.com |
order@ejendals.com |
www.ejendals.com
Declaration of Conformity →
www.ejendals.com/conformity
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>