ejendals TEGERA 8803R Lightweight Contact Heat Resistant Warehouse Gloves Instruction Manual
- June 4, 2024
- ejendals
Table of Contents
INSTRUCTIONS FOR USE
PRODUCT SPECIFIC INFORMATION
ONLY ON THIS PAGE
TEGERA 8803R Lightweight Contact Heat Resistant Warehouse Gloves
8803R
Synthetic glove, nitrile, nitrile foam, water-based PU, 3/4 dipped, double-
dipped, foam grip pattern, 18 gg, nylon, spandex, Cat. II, black, yellow,
withstands contact heat up to 100°C, DMF (DMF) free, oil and grease resistant,
for precision work
| 420:2003
+ A1:2009
---|---
| 388:2016
4121X
| 407:2004
X1XXXX
INSTRUCTIONS FOR USE – CATEGORY II
SEE THE FRONT PAGE FOR PRODUCT-SPECIFIC INFORMATION
Carefully read these instructions before using this product.
DECLARATION OF CONFORMITY
www.ejendals.com/conformity
EXPLANATION OF PICTOGRAMS 0 = Below the minimum performance level for the
given individual hazard X= Not submitted to the test or test method not
suitable for the glove design or material Warning! This product is designed to
provide protection specified in PPE Regulation (EU) 2016/425 with the detailed
levels of performance presented below. However, always remember that no item
of PPE can provide full protection and caution must always be taken when
exposed to risks.
407:2004
PROTECTIVE GLOVES AGAINST THERMAL RISKS (HEAT AND/OR FIRE)
A: Burning behavior
B: Contact heat
C: Convective heat
D: Radiant heat
E: Small splashes of molten metal
F: Large quantities of molten metal
PERFORMANCE (A-F)
Min. 0; Max. 4
Warning: EN 407:2004: if the glove consists of separate parts which are
not permanently interconnected, the performance levels and the protection only
apply to the complete assembly. If the gloves have a performance level 1, 2 or
X in burning behavior in EN 407:2004 the gloves should not come in contact
with a naked flame.
A. Abrasion resistance
B. Blade cut resistance
C. Tear resistance
D. Puncture resistance
E. Cut Resistance TDM (EN ISO13997),
F. Impact Protection
Min. 0; Max. 4
Min. 0; Max. 5
Min. 0; Max. 4
Min. 0; Max. 4
Min. A; Max. F P=Pass
PROTECTIVE GLOVES AGAINST MECHANICAL RISKS. Protection levels are
measured from area of the glove palm. Warning: For gloves with two or more
layers the overall classification of EN 388:2016 does not necessarily reflect
the performance of the outmost layer. Do not use these gloves near moving
elements or machinery with unprotected parts. For dulling during the cut
resistance test, the coupe test results are only indicative while the TDM cut
resistance test is the reference performance result.
SUITABLE FOR CONTACT WITH FOOD SPECIFIED IN REGULATION (EU) 10/2011 AND
1935/2004.
All gloves/sleeves that are suitable for foodstuff may not be suitable for all
types of food. To know for which foodstuff the glove/sleeve may be used please
see the Food declaration of conformity. Contact Ejendals for more information.
420:2003 + A1:2009 PROTECTIVE GLOVES – GENERAL REQUIREMENTS AND TEST
METHODS
Finger dexterity test: Min. 1; Max. 5
FITTING AND SIZING: All sizes comply with EN 420:2003+A1:2009 for
comfort, fit, and dexterity, if not explained on the front page. If the short
model symbol is shown on the front page, the glove is shorter than a standard
glove, in order to enhance the comfort for special purposes – for example,
fine assembly work. Only wear the products in a suitable size. Products that
are either too loose or too tight will restrict movement and will not provide
the optimal level of protection.
STORAGE AND TRANSPORT:
Ideally stored in dry and dark condition in the original package, between +10º – +30ºC.
INSPECTION BEFORE USE:
Check that the glove does not present holes, cracks, tears, color changes etc.
If the product becomes damaged it will NOT provide the optimal protection and
must be disposed of. Never use a damaged product.
SHELF LIFE: The nature of the materials used in this product means that
the life of this product cannot be determined as it will be affected by many
factors, such as storage conditions, usage etc.
CARE AND MAINTENANCE:
The user bares sole responsibility for submitting the product to mechanical washing after use, as unknown substances can contaminate the product during use and may affect the performance levels of the product. To care for your product, we recommend that you rinse in cold water and line dry in room temperature.
DISPOSAL:
According to local environmental legislation.
EN ISO 21420: The glove contains natural rubber which may cause allergy.
**ALLERGENS:
**
This product may contain components that may be a potential risk to allergic
reactions. Do not use in case of hypersensitivity signs.
For more information contact Ejendals.
LATEX FREE
YES
NO
INFINITY™
CONFIDENCE IN TEXTILES
STANDARD 100: SE 14-214 Swerea IVF
Tested for harmful substances.
www.oeko-tex.com/standard100
OUTER MATERIAL SPECIFICATION Nitrile INNER MATERIAL SPECIFICATION Nylon,
elastane
EU-TYPE EXAMINATION 0075 CTC, 4 rue Hermann Frenkel, 69367 Lyon Cedex 07
France
ONLY FOR EURASIAN ECONOMIC COMMUNITY CUSTOMS UNION MEMBERS
Limavägen 28, SE-793 32 Leksand, Sweden
Phone +46 (0) 247 360 00
Fax +46 (0) 247 360 10
info@ejendals.com
order@ejendals.com
www.ejendals.com
Declaration of Conformity
www.ejendals.com/conformity
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>