ejendals 6 Pairs Tegera 8832R Instruction Manual
- June 3, 2024
- ejendals
Table of Contents
INSTRUCTIONS FOR USE
PRODUCT SPECIFIC INFORMATION
ONLY ON THIS PAGE
TEGERA®8832R
6 Pairs Tegera 8832R
Cut resistant glove, winter-lined, latex, 3/4 dipped, double-dipped, sandy finish, cut resistance level D, 10 gg, 13 gg, acrylic, CRF® Technology, stainless steel fibre yarn, Cat. II, black, blue, withstands contact heat up to 250°C, pair packed, water repellent, for allround work EN ISO 21420:2020
| EN 388:2016+A1:2018 2X42D
---|---
| EN 407:2020 No Flame Protection X2XXXX
| EN 511:2006 12X
INSTRUCTIONS FOR USE – CATEGORY II
SEE FRONT PAGE FOR PRODUCT SPECIFIC INFORMATION Carefully read these
instructions before using this product.
DECLARATION OF CONFORMITY
www.ejendals.com/conformity
EXPLANATION OF PICTOGRAMS 0 = Below the minimum performance level for the
given individual hazard X= Not submitted to the test or test method not
suitable for the glove design or material Warning! This product is designed to
provide protection specified in PPE Regulation (EU) 2016/425 and PPE
Regulation 2016/425 as amended and brought into UK law with the detailed
levels of performance presented below. However, always remember that no item
of PPE can provide full protection and caution must always be taken when
exposed to risks.
PROTECTIVE GLOVES AGAINST THERMAL RISKS (HEAT AND/OR FIRE) EN 407:2020
A: Limited flame spread
B: Contact heat PERFORMANCE (A-F) Min. 0; Max. 4
C: Convective heat
ABCDEF
D: Radiant heat
E: Small splashes of molten metal
F: Large quantities of molten metal
Warning: EN 407:2020: if the glove consists of seperate parts which are
not permanently interconnected, the perfomance levels and the protection only
apply to the complete assembly. If the gloves have a performance level 1, 2 or
X in limited flamespread in EN 407:2020 the gloves should not come in contact
with naked flame. Glove tested according to the 6.6 “small splashed of molten
metal” is not suitable for welding activities. In the event of a moltenmetal
splash the glove may not eliminate all risks of burn and the user shall leave
the working place immediately and take off the glove. No flame protection
EN 388:2016 +A1:2018
A. Abrasion resistance Min. 0; Max. 4
B. Blade cut resistance Min. 0; Max. 5
C. Tear resistance Min. 0; Max. 4
ABCDEF
D. Puncture resistance Min. 0; Max. 4
E. Cut Resistance TDM Min. A; Max. F (EN ISO13997),
F. Impact Protection P=Pass
PROTECTIVE GLOVES AGAINST MECHANICAL RISKS. Protection levels
are measured from area of glove palm. Warning: For gloves with two or more
layers the overall classification of EN 388:2016 +A1:2018 does not necessarily
reflect the performance of the outmost layer. Do not use these gloves near
moving elements or machinery with unprotected parts. For dulling during the
cut resistance test, the coupe test results are only indicative while the TDM
cut resistance test is the reference performance result.
EN 511:2006 PROPERTY
PROPERTY
A. Convective cold PERFORMANCE
B. Contact cold Min. 0; Max. 4
C. Water penetration 0 (Fail); 1 (Pass)
ABC
Warning: EN 511:2006: if the glove consists of seperate parts which are not
permanently interconnected, the perfomance levels and the protection only
apply to the complete assembly. EN 511: Care must be taken when choosing the
correct glove with regards to the maximum user exposure. If not water proof,
the glove may lose its insulating properties if wet. EN511:2006 Annex B table
B.1 shows various parameters to be considered. Studies have established
certain correlations between these parameters and the level of thermal
insulation required to protect in cold conditions. The table given in Annex B
of EN342:2004 is an example of such data.
ISO 21420:2020 PROTECTIVE GLOVES – GENERAL REQUIREMENTS AND TEST METHODS
Finger dexterity test: Min. 1; Max. 5
FITTING AND SIZING: All sizes comply with the EN ISO 21420:2020 for
comfort, fit and dexterity, if not explained on the front page.If the short
model symbol is shown on the front page, the glove is shorter than a standard
glove, in order to enhance the comfort forspecial purposes – for example fine
assembly work. Only wear the products in a suitable size. Products which are
either too loose ortoo tight will restrict movement and will not provide the
optimal level of protection.
STORAGE AND TRANSPORT: Ideally stored in dry and dark condition in the
original package, between +10º – +30ºC.
INSPECTION BEFORE USE: Check that the glove does not present holes,
cracks, tears, colour change etc. If the product becomes damaged it will NOT
provide the optimal protection and must be disposed of. Never use a damaged
product. Wear (or take off) gloves oneat a time. Replace gloves regularly for
hygienic use
SHELF LIFE: The nature of the materials used in this product means that
the life of this product cannot be determined as it will be affected by many
factors, such as storage conditions, usage etc.
CARE AND MAINTENANCE: The user bares sole responsibility for submitting
the product to mechanical washing after use, as unknownsubstances can
contaminate the product during use and may affect the performance levels of
the product. To care for your product, werecommend that you rinse in cold
water and line dry in room emperature.
DISPOSAL: According to local environmental legislations.
The glove contains natural rubber which may cause allergy.
ALLERGENS: This product may contain components that may be a potential
risk to allergic reactions. Do not use in case of hypersensitivity signs. For
more information contact Ejendals.
LATEX FREE
YES NO
Contact heat rating valid for palm area only
OUTER MATERIAL SPECIFICATION Natural latex
INNER MATERIAL SPECIFICATION Acrylic, HPPE, stainless steel fibre yarn,
polyester, nylon
SIZE RANGE (EU) 7,8,9,10,11,12
EU-TYPE EXAMINATION 2777 Satra Technology Europe Ltd Bracetown Business
Park, Clonee, Dublin 15, Dublin, Ireland
UKCA-TYPE EXAMINATION
0321 SATRA Technology Centre, Wyndham Way, Telford Way, Kettering,
Northamptonshire, NN16 8SD, United Kingdom
Made in China
ONLY FOR EURASIAN ECONOMIC COMMUNITY CUSTOMS UNION MEMBERS
UK-IMPORTER
Ejendals ltd, Sweden House, 5 upper Montagu Street,
London, England, W1 2AG
EJENDALS AB
Limavägen 28, SE-793 32 Leksand, Sweden
info@ejendals.com |
order@ejendals.com |
www.ejendals.com
Declaration of Conformity
www.ejendals.com/conformity
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>