ejendals Tegera 295 Black Blue White Cold Resistant Gloves Instruction Manual
- June 14, 2024
- ejendals
Table of Contents
INSTRUCTIONS FOR USE
PRODUCT SPECIFIC INFORMATION
ONLY ON THIS PAGE
Tegera 295 Black Blue White Cold Resistant Gloves
****
TeGera ® 295
Leather glove, winter-lined, full grain goatskin, spandex, Thinsulate™ 40g,
Cat. II, blue, grey, white, waterproof, elasticated 360°, for allround work
EN ISO 21420:2020
EN 511:2006 121
EN 388:2016+A1:2018 2121X
EN 511 cl 4.3 Waterpenetration (ISO 15383): Pass
OUTER MATERIAL SPECIFICATION Leather, elastane, polyester, natural latex
MIDDLE MATERIAL SPECIFICATION Polyethylene
INNER MATERIAL SPECIFICATION Polyester
SIZE RANGE (EU) 6,7,8,9,10,11,12,13,14,15
**** EU-TYPE EXAMINATION 0321 SATRA Technology Centre, Wyndham Way, Telford
Way, Kettering, Northamptonshire, NN16 8SD, United Kingdom
** INSTRUCTIONS FOR USE – CATEGORY II
SEE FRONT PAGE FOR PRODUCT SPECIFIC INFORMATION
Carefully read these instructions before using this product.
DECLARATION OF CONFORMITY**
www.ejendals.com/conformity
EXPLANATION OF PICTOGRAMS
D = Below the minimum performance level for the given individual hazard
X= Not submitted to the test or test method not suitable for the glove design
or material
Warning! This product is designed to provide protection specified in PPE
Regulation (EU) 2016/425 and PPE Regulation 2016/425 as amended and brought
into UK law with the detailed levels of performance presented below. However,
always remember that no item of PPE can provide full protection and caution
must always be taken when exposed to risks.
EN 388:2016 +A1:2018
A. Abrasion resistance ………………Min. 0; Max. 4
B. Blade cut resistance……………….. Min. 0; Max. 5
C. Tear resistance…………………….. Min. 0; Max. 4
D. Puncture resistance………………….. Min. 0; Max. 4
E. Cut Resistance TDM……………… Min. A; Max. F (EN ISO13997),
F. Impact Protection……………………… P=Pass
PROTECTIVE GLOVES AGAINST MECHANICAL RISKS. Protection levels are
measured from area of glove palm. Warning: For gloves with two or more layers
the overall classification of EN 388:2016 +A1:2018 does not necessarily
reflect the performance of the outmost layer. Do not use these gloves near
moving elements or machinery with unprotected parts. For dulling during the
cut resistance test, the coupe test results are only indicative while the TDM
cut resistance test is the reference performance result.
ABCDEF EN 511:2006
PROPERTY………………… PERFORMANCE
A. Convective cold………… Min. 0; Max. 4
B. Contact cold……………………. Min. 0; Max. 4
C. Water penetration…………… 0 (Fail); 1 (Pass)
Warning: EN 511:2006: if the glove consists of seperate parts which are
not permanently interconnected, the perfomance levels and the protection only
apply to the complete assembly. EN 511: Care must be taken when choosing the
correct glove with regards to the maximum user exposure. If not water proof,
the glove may lose its insulating properties if wet. EN511:2006 Annex B table
B.1 shows various parameters to be considered. Studies have established
certain correlations between these parameters and the level of thermal
insulation required to protect in cold conditions. The table given in Annex B
of EN342:2004 is an example of such data.
Abrasion resistance according to the American National Standard Institute
105-2016. Levels 1-6
EN ISO 21420:2020 PROTECTIVE GLOVES – GENERAL REQUIREMENTS AND TEST METHODS
Finger dexterity test: Min. 1; Max. 5
FITTING AND SIZING:
All sizes comply with the EN ISO 21420:2020 for comfort, fit and dexterity, if
not explained on the front page.
If the short model symbol is shown on the front page, the glove is shorter
than a standard glove, in order to enhance the comfort for special purposes –
for example fine assembly work. Only wear the products in a suitable size.
Products which are either too loose or too tight will restrict movement and
will not provide the optimal level of protection.
STORAGE AND TRANSPORT:
Ideally stored in dry and dark condition in the original package, between +10º
– +30ºC.
INSPECTION BEFORE USE : Check that the glove does not present holes,
cracks, tears, colour change etc. If the product becomes damaged it will NOT
provide the optimal protection and must be disposed of. Never use a damaged
product. Wear (or take off) gloves one at a time. Replace gloves regularly for
hygienic use
SHELF LIFE: The nature of the materials used in this product means that
the life of this product cannot be determined as it will be affected by many
factors, such as storage conditions, usage etc.
CARE AND MAINTENANCE:
Gloves/sleeves that can be mechanically washed will carry laundry symbols. It
is the customer or launderer who is responsible for the performance of the
gloves after laundering when the gloves have already been used. Ejendals
cannot be held liable for this DISPOSAL: According to local environmental
legislations.
The glove contains natural rubber which may cause allergy.
ALLERGENS: This product may contain components that may be a potential
risk to allergic reactions. Do not use in case of hypersensitivity signs.
For more information contact Ejendals.
Latex free yes no
Made in China
** ONLY FOR EURASIAN ECONOMIC COMMUNITY CUSTOMS UNION MEMBERS
uk-importer
Ejendals ltd, Sweden House, 5 upper Montagu Street,
London, England, W1 2AG
ejendals ab**
Limavägen 28, SE-793 32 Leksand, Sweden
info@ejendals.com |
order@ejendals.com |
www.ejendals.com
Declaration of Conformity
www.ejendals.com/conformity
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>