ejendals TEGERA 8808 Cut Resistant Glove Instruction Manual
- June 3, 2024
- ejendals
Table of Contents
INSTRUCTIONS FOR USE
PRODUCT SPECIFIC INFORMATION
**ONLY ON THIS PAGE
**
TEGERA 8808 Cut Resistant Glove
TeGera ® 8808
Cut resistant glove, nitrile, nitrile foam, waterbased PU, 3/4 dipped, double-
dipped, foam grip pattern, cut resistance level D, 15 gg, CRF® Technology,
glass fibre thread, nylon, spandex, Cat. II, black, yellow, withstands
contact heat up to 100°C,DMF (DMFa) free, oil and grease resistant,
anatomically designed, for assembly work
OUTER MATERIAL SPECIFICATION Nitrile INNER MATERIAL SPECIFICATION Glass fibre thread, HPPE, nylon, elastane EU-TYPE EXAMINATION 0075 CTC, 4 rue Hermann Frenkel, 69367 Lyon Cedex 07 France
INSTRUCTIONS FOR USE – CATEGORY II
SEE FRONT PAGE FOR PRODUCT SPECIFIC INFORMATION
Carefully read these instructions before using this product.
DECLARATION OF CONFORMITY
www.ejendals.com/conformity
EXPLANATION OF PICTOGRAMS 0 = Below the minimum performance level for the
given individual hazard X= Not submitted to the test or test method not
suitable for the glove design or material
Warning! This product is designed to provide protection specified in PPE
Regulation (EU) 2016/425 with the detailed levels of performance presented
below. However, always remember that no item of PPE can provide full
protection and caution must always be taken when exposed to risks.
407:2004 PROTECTIVE GLOVES AGAINST THERMAL RISKS (HEAT AND/OR FIRE)A:
Burning behaviour
B: Contact heat
C: Convective heat
D: Radiant heat
E: Small splashes of molten metal
F: Large quantities of molten metal
PERFORMANCE (A-F)
Min. 0; Max. 4
Warning: 407:2004: if the glove consists of seperate parts which are not permanently interconnected, the perfomance levels and the protection only apply to the complete assembly. If the gloves have a performance level 1, 2 or X in burning behaviour in EN 407:2004 the gloves should not come in contact with naked flame.
| A. Abrasion resistance B. Blade cut resistance C. Tear resistance
D. Puncture resistance E. Cut Resistance TDM (EN ISO13997),
F. Impact Protection| Min. 0; Max. 4
Min. 0; Max. 5
Min. 0; Max. 4
Min. 0; Max. 4
Min. A; Max. F
P=Pass
---|---|---
PROTECTIVE GLOVES AGAINST MECHANICAL RISKS. Protection levels are measured from area of glove palm. Warning: For gloves with two or more layers the overall classification of EN 388:2016 does not necessarily reflect the performance of the outmost layer. Do not use these gloves near moving elements or machinery with unprotected parts. For dulling during the cut resistance test, the coupe test results are only indicative while the TDM cut resistance test is the reference performance result.
SUITABLE FOR CONTACT WITH FOOD SPECIFIED IN REGULATION (EU) 10/2011 AND 1935/2004. All gloves/sleeves that are suitable for foodstuff may not be suitable for all types of food. To know for which foodstuff the glove/sleeve may be used please see the Food declaration of conformity. Contact Ejendals for more information.
EN 420:2003 + A1:2009 PROTECTIVE GLOVES – GENERAL REQUIREMENTS AND TEST
METHODS Finger dexterity test: Min. 1; Max. 5
FITTING AND SIZING: All sizes comply with the EN 420:2003+A1:2009 for comfort,
fit and dexterity, if not explained on the front page. If the short model
symbol is shown on the front page, the glove is shorter than a standard glove,
in order to enhance the comfort for special purposes – for example fine
assembly work. Only wear the products in a suitable size. Products which are
either too loose or too tight will restrict movement and will not provide the
optimal level of protection.
STORAGE AND TRANSPORT: Ideally stored in dry and dark condition in the
original package, between +10º – +30ºC.
INSPECTION BEFORE USE:
Check that the glove does not present holes, cracks, tears, colour change etc.
If the product becomes damaged it will NOT provide the optimal protection and
must be disposed of. Never use a damaged product.
SHELF LIFE: The nature of the materials used in this product means that the
life of this product cannot be determined as it will be affected by many
factors, such as storage conditions, usage etc.
CARE AND MAINTENANCE:
The user bares sole responsibility for submitting the product to mechanical
washing after use, as unknown substances can contaminate the product during
use and may affect the performance levels of the product. To care for your
product, we recommend that you rinse in cold water and line dry in room
temperature.
DISPOSAL: According to local environmental legislations.
EN ISO 21420: The glove contains natural rubber which may cause allergy.
ALLERGENS: This product may contain components that may be a potential risk to
allergic reactions. Do not use in case of hypersensitivity signs.
For more information contact Ejendals.
latex free yes no
Documents / Resources
|
ejendals TEGERA 8808 Cut Resistant
Glove
[pdf] Instruction Manual
TEGERA 8808, Cut Resistant Glove, TEGERA 8808 Cut Resistant Glove, Resistant
Glove, Glove
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>