ejendals TEGERA 9180 Anti Vibration Glove Instruction Manual
- June 4, 2024
- ejendals
Table of Contents
ejendals TEGERA 9180 Anti Vibration Glove Instruction Manual
INSTRUCTIONS FOR USE
Carefully read these instructions before using this product.
EXPLANATION OF PICTOGRAMS 0 = Below the minimum performance level for the given individual hazard X= Not submitted to the test or test method not suitable for the glove design or material
Warning! This product is designed to provide protection specified in PPE Regulation (EU) 2016/425 with the detailed levels of performance presented below. However, always remember that no item of PPE can provide full protection and caution must always be taken when exposed to risks.
EN 388:2016
- A. Abrasion resistance Min. 0; Max. 4
- B. Blade cut resistance Min. 0; Max. 5
- C. Tear resistance Min. 0; Max. 4
- D. Puncture resistance Min. 0; Max. 4
- E. Cut Resistance TDM Min. A; Max. F (EN ISO13997),
- F. Impact Protection P=Pass
PROTECTIVE GLOVES AGAINST MECHANICAL RISKS.
Protection levels are measured from area of glove palm.
Warning: For gloves with two or more layers the overall classification of
EN 388:2016 does not necessarily reflect the performance of the outmost layer.
Do not use these gloves near moving elements or machinery with unprotected
parts. For dulling during the cut resistance test, the coupe test results are
only indicative while the TDM cut resistance test is the reference performance
result.
ABCDEF
The glove is shorter than a standard glove, in order to enhance the comfort for special purposes – for example fine assembly work.
EN ISO 10819:2013
MECHANICAL VIBRATION AND SHOCK Hand-arm vibration. Measurement and evaluation
of the vibration transmissibility of gloves at the palm of the hand.
EN 420:2003 + A1:2009 PROTECTIVE GLOVES – GENERAL REQUIREMENTS AND TEST METHODS
Finger dexterity test: Min. 1; Max. 5
FITTING AND SIZING
All sizes comply with the EN 420:2003+A1:2009 for comfort, fit and dexterity, if not explained on the front page. If the short model symbol is shown on the front page, the glove is shorter than a standard glove, in order to enhance the comfort for special purposes – for example fine assembly work. Only wear the products in a suitable size. Products which are either too loose or too tight will restrict movement and will not provide the optimal level of protection.
STORAGE AND TRANSPORT: Ideally stored in dry and dark condition in the original package, between +10º – +30ºC.
INSPECTION BEFORE USE
Check that the glove does not present holes, cracks, tears, colour change etc.
If the product becomes damaged it will NOT provide the optimal protection and
must be disposed of. Never use a damaged product.
SHELF LIFE: The nature of the materials used in this product means that
the life of this product cannot be determined as it will be affected by many
factors, such as storage conditions, usage etc.
CARE AND MAINTENANCE
The user bares sole responsibility for submitting the product to mechanical washing after use, as unknown substances can contaminate the product during use and may affect the performance levels of the product. To care for your product, we recommend that you rinse in cold water and line dry in room temperature.
DISPOSAL
According to local environmental legislations. ’
EN ISO 21420: The glove contains natural rubber which may cause allergy.
ALLERGENS: This product may contain components that may be a potential
risk to allergic reactions. Do not use in case of hypersensitivity signs. For
more information contact Ejendals.
LATEX FREE: No
DECLARATION OF CONFORMITY
www.ejendals.com/conformity
ONLY FOR EURASIAN ECONOMIC COMMUNITY CUSTOMS UNION MEMBERS
Support
EJENDALS AB
Limavägen 28, SE-793 32 Leksand, Sweden
Phone +46 (0) 247 360 00
Fax +46 (0) 247 360 10
info@ejendals.com
order@ejendals.com
www.ejendals.com
Declaration of Conformity
www.ejendals.com/conformity
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>