VIVO Black V-Base Studio TV Stand Instruction Manual
- June 7, 2024
- Vivo
Table of Contents
VIVO Black V-Base Studio TV Stand Instruction Manual
SKU: STAND-TV70B
Scan the QR
code with your mobile device or follow the link for helpful videos and
specifications related to this product.
htthttps://vivo-us.com/products/stand-
tv70bps:/
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
www.vivo-us.com
Chat live with an agent!
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1) Leg
B (x1) Pole
C (x2) Foot
D (x1) Upper VESA Bracket
E (x1) Lower VESA Bracket
F (x2) Foot Pad
G (x4) M8x12
H (x4) M6x15
I (x2) Cable Cover
J (x1) 4mm Allen Wrench
K (x1) 5mm Allen Wrench
M-A (x4) M5x14
M-B (x4) M6x14
M-C (x4) M6x30
M-D (x4) M8x30
M-E (x4) M8x50
M-F (x4) Square Washer
M-G (x8) 5mm Spacer
M-H (x8) 15mm Spacer
P-A (x1) Steel Cable
P-B (x2) Security Clip
P-C (x2) Security Cable Clamp
P-D (x1) 2mm Allen Wrench
P-E (x4) ST4.8*38 Screw
P-F (x4) Anchor
P-G(x2) D5 Washe
NOTE : SOME HARDWARE MAY NOT BE USED
TOOLS NEEDED
DO NOT EXCEED
WEIGHT CA88PlAbsCITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Slide the feet (C) onto the base of the leg (A). Insert M8x12 bolts (G) into
the bottom holes of the feet. Tighten with the 5mm Allen wrench (K). Insert
M6x15 bolts (H) through the base into the rear holes of the feet. Tighten with
the 5mm Allen wrench (K). Screw the foot pads (F) into the base, and adjust
foot pads to sit level on the floor.
STEP 2
Screw the pole (B) onto the leg (A). Loosen the set screws in the collar using
the 4mm Allen wrench (J), and adjust the collar height to the recommended
position below the top of the pole based on your TV’s VESA mounting hole
pattern. Tighten the set screws, making sure they face towards the back of the
stand.
- A – VESA Height = 200mm: 4″ – 6.7″ (90-110mm)
- B – VESA Height = 300mm: 3.5″ – 4.3″ (100-170mm)
- C – VESA Height = 400mm: 2″ – 2.75″ (50-70mm)
Note:
- Please secure the locking collar before attaching the TV screen.
- Make sure the screw holes face backwarlds. 1
STEP 3
Remove the screw from the lower VESA bracket (E) to separate into parts E1 and
E2, and open the clamp.
STEP 4
OPTION A:
Flat Back TV Position VESA brackets horizontally on the back of the TV, making
sure the upper bracket (D) is on top and the lower bracket (E2) is below.
Secure using screws (M-A or M-B) with square washers (M-F) and D5 washers
(P-G), with security clips (P-B) installed to the top holes.
OPTION B:
Curved Back TV Position VESA brackets horizontally on the back of the TV,
making sure the upper bracket (D) is on top and the lower bracket (E2) is
below. Secure using screws (M-C, M-D or M-E) with square washers (M-F) and
spacers (M-G, M-H), with security clips (P-B) installed to the top holes.
STEP 5
Slide the TV with VESA brackets (D, E2) onto the pole (B). Close the clamp on
the lower VESA bracket over the pole and secure with previously removed screw
(E1).
STEP 6
Route cables through the cables holes in the leg (A). Install cable covers (I)
to the cables holes, using pliers to break out sections for x2 or x3 cables if
needed.
STEP 7
OPTION A: Wood Wall Installation Using security cable clamps (P-C) as guides,
mark drilling locations on the wall. Use of a stud finder is recommended.
Drill holes at least 1.6″ (40mm) deep using a 1/8″ (3.5mm) drill bit. Mount
clamps to the wall using 1-1/4″ screws (P-E). Thread steel cable (P-A) through
the security clips on the TV and center holes in the cable clamps as shown,
then tighten clamps using the 2mm Allen wrench (P-C).
OPTION B:
Concrete/Brick Wall Installation Using security cable clamps (P-C) as guides,
mark drilling locations on the wall. Drill holes at least 1.6″ (40mm) deep
using a 9/32″ (7mm) drill bit. Insert anchors (P-F) into the holes and mount
clamps to the wall using 1-1/4″ screws (P-E). Thread steel cable (P-A) through
the security clips on the TV and center holes in the cable clamps as shown,
then tighten clamps using the 2mm Allen wrench (P-D).
Support:
If any parts are received damaged or defective, please contact us. We are
happy to replace parts to ensure you have a fully functioning product.
www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Black V-Base Studio TV Stand for 49" to 70" TVs – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>