VIVO Black 44″ x 24″ Electric Desk Instruction Manual

: June 7, 2024
: Vivo

VIVO Black 44″ x 24″ Electric Desk Instruction Manual

SKU: DESK-E144B

qr code Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
Instruction Manual https://vivo-us.com/products/desk-e144b

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.

ELECTRICAL SAFETY INSTRUCTIONS

THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY

DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE DAMAGED PARTS.
NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT WITH LIQUIDS.
ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
OUTDOOR USE IS PROHIBITED.

WARNING: CHOKING HAZARD

SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

TOOLS NEEDED

DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury.

ASSEMBLY STEPS

STEP 1

Assemble the crossbar (6) to the legs (8, 9) using M8x47 bolts (A) and tighten with the 5mm Allen wrench (E).

STEP 2

Place the feet (4) on the legs as shown, then insert and tighten M6x35 bolts (C) using the 5mm Allen wrench (E). Screw the foot pads (G) into the feet.

diagram, engineering drawing

STEP 3

Place the feet (4) on the legs as shown, then insert and tighten M6x35 bolts (C) using the 5mm Allen wrench (E). Screw the foot pads (G) into the feet.
Assemble the side brackets (5) to the legs using M6x10 bolts (B) and tighten with the 4mm Allen wrench (E). Insert the anti-vibration pads (H) into the desktop mounting holes in the crossbar and side brackets.
diagram

STEP 4

Insert the sync rod (7) into the leg (9). Loosen the knob on the sync rod, then extend the rod onto the motor leg (8) and tighten the knob. Tighten the set screw on the end of the sync rod using the 2mm Allen wrench (E)
diagram, engineering drawing .

STEP 5

Insert the sync rod (7) into the leg (9). Loosen the knob on the sync rod, then extend the rod onto the motor leg (8) and tighten the knob. Tighten the set screw on the end of the sync rod using the 2mm Allen wrench (E).
Assemble the desktop halves (11) using the connectors (10) with M5x16 screws (D) and a Phillips screwdriver.

STEP 6

Hang the cable tray (3) over the crossbar (6), opposite from the sync rod (7), then carefully place the assembled frame upside down on the desktop (11). Secure the frame to the desktop using M5x16 screws (D) and a Phillips screwdriver

diagram, engineering drawing

STEP 7

Hang the cable tray (3) over the crossbar (6), opposite from the sync rod (7), then carefully place the assembled frame upside down on the desktop (11). Secure the frame to the desktop using M5x16 screws (D) and a Phillips screwdriver.Mount the control panel (1) to the desktop (11) using M5x16 screws (D) with a Phillips screwdriver. Connect the AC adapter (2) and motor to the control panel. Organize cables using the cable clips (F).

STEP 8

Carefully turn the desk right side up and connect the AC adapter (2) to a wall outlet. If necessary, adjust foot pads (G) to level the desk. The desk is now ready for use. Please refer to the Controller User Guide for operating instructions.

CAUTION!

Failure to follow these instructions may result in property damage and/or personal injury.

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response times. If anyparts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.