kogan KAHTP20WHTA 2000W White Glass Portable Panel Heater User Manual
- June 7, 2024
- Kogan
Table of Contents
kogan KAHTP20WHTA 2000W White Glass Portable Panel Heater User Manual
General Directions
- Remove packaging and make sure the heater is intact and If in any doubt, do not use the heater, but instead contact the Kogan.com customer support team.
Packaging materials (plastic bags, polystyrene, staples etc..} must be kept out of reach of children as they could be hazardous.
Caution:
The heater must only be used be responsible adults; For their safety,
children and persons with reduced mental capacities must not use this
appliance unless under the supervision of responsible adults;
-
Before connecting the heater, check the power cable to ensure that it is not damaged.
-
This heater must only be used for the purpose for which it has been manufactured, ie for additional electrical heating in Any other use is considered improper use, and therefore dangerous and will void your warranty. Kogan.com are not responsible for any damage caused by improper, incorrect or unreasonable use.
-
Before cleaning or maintenance, disconnect the heater from the power mains by removing the plug from the outlet.
-
If the appliance is faulty and/or operating incorrectly, switch it off and unplug it, then contact the com customer support team.
-
Switch the appliance off at the wall socket and unplug it when not in use.
-
The use of electrical appliances calls for the awareness of some basic rules, such as:
do not use the appliance near sources of water such as baths, showers or pools.
do not touch the appliance with wet or damp hands or feet -
Do not use the heater in the presence of potential flammable or explosive liquids or gases.
Safeey Warnings
-
In order to avoid overheating, it is advisable to unwind the entire length of the power cord.
-
Check that the electric capacity of the system and the power outlets in your home are adequate for the maximum power stated on the plate. If in doubt, contact a qualified electrician.
-
Do not leave the heater plugged in when it is not required. Unplug the heater from the mains after it has been switched off
-
Do not obstruct the ventilation or heat dispersion openings.
-
The power cord on this appliance must not be replaced by the user. If the cord is damaged or requires replacement, contact the com customer support team.
-
Avoid anything having direct contact with the hot surfaces of the heater. Check that the power cord is not placed in front of the hot air outlet grille.
-
Do not use near bathtubs, showers or basins
-
Use in an upright position only
-
Keep the suction grille clean
-
Do not use the heater directly below a fixed power outlet
-
Do not cover the heater with anything at all
-
Some parts of the heater can become very hot and cause Particular attention must be given when used near children and vulnerable people.
-
Keep the heater and the power cord out of reach of children.
Product Features
Elegant glass panel
- High quality aluminium heating element: quick heating with low power usage
- Touch screen control and remote control
- 24 hour timer for startup and/or shutdown
- Digital display with automatic room temperature display
- Suitable for wall-mounting or free standing with tripod
Fooe Assembly
Please put the feet into the heaters housing, then secure them with the
supplied ST4 x 1O x 3 screws. To move the appliance, switch it off and
disconnect it from the power mains, then wait for the heater to cool down. Use
the side gripping points for transport.
Wall Assembly
Please note that the heater must be installed at least 15cm above the floor and 5Ocm below the ceiling.
- Make two holes (515mm apart for the 2OOOW heater}
- With a diameter of 8mm and a depth of 4Omm, insert the supplied anchors in the holes, then use a screwdriver to tighten the screws supplied with the anchors. These screws must protrude from the anchor. You can then hang the heater using the hook holes on the back of the unit.
Note:
before drilling, make sure there are no wires or pipes located under the
wall.
Operation
Insert the plug in a suitable power socket. Touch screen buttons located on
the product correspond to the remote control.
- Display
- Temperature
- Timer
- – Button
- Power
- Mode
- + Button
When the heater is plugged in, press POWER to set the functions. The right part of the display will show Press POWER again to reset the functions. The right part of the display will now show the and symbols.The heater will now be working in lower power heating mode.
Mode
Press ‘5-mode’ to regulate the low and high temperature power mode.
Temperature
The internal temperature is displayed every time the heater is turned on. The
temperature can be set when the heater is either in standby mode or actively
heating. When the room temperature reaches the set level, the high temperature
power stops and the low temperature power mode will remain active.
When the room temperature is 2 degrees over the set temperature, both the high
and low temperature power modes will stop operating. The heater will begin
operating again only when the temperature decreases 2 degrees with respect to
the set temperature. The temperature regulation range is 15o C – 35o C.
Timer
The timer button can be set to stop the heater at the desired time, with a timer interval between of between 1 to 24 hours.
Operating Sound
The heater will emit a beep tone upon each successful operation setting.
Memory
The heater can store the last temperature setting in its memory. This temperature will be shown at start-up. If the power settings are different, start-up reset will go to those set as default.
Usage
Insert the plug into a suitable power socket.
Turn on the side switch. A beep will be emitted and the temperature icon
°C and the timer icon ‘ ‘ will appear on the display. The figure to the
right of the temperature icon will show the room temperature with the time set
at ‘O’. The machine will go into stand-by.
- Press POWER and the low temperature icon will The appliance is now working in low heat power mode.
- Press MODE: Low temperature and high temperature can be
- Shut-down: the icons will not be lit
Temperature selection: °C
Press the temperature button and the °C icon will flash. Press+ or – to
select the desired temperature within the range of 15 o C and 35o C. The
temperature indicator will remain lit for a short time.
Timer Selection: press the timer button and the ‘-‘ icon will flash. Press+ or
– to select the desired ON or OFF range from between 1 and 24 hours. The
remaining time will appear.
LCD room temperature display: the appliance will stop when the temperature
exceeds 2 degrees with respect to the set temperature.
Press POWER and the room temperature will appear, the timer will show “O”.
Temperature powers will switch off and the appliance will go into standby.
Maintenance
Before carrying out routine cleaning, switch the heater off and disconnect the main power. Use a soft, damp cloth only. Do not use abrasive cleaning chemicals.
Do not EVER submerge any parts of the heater in water.No parts of the heater are able to be repaired by customers, as this can be hazardous and will void your warranty. Please contact the Kogan.com customer support team if the heater operates in any manner that does not appear normal.
This marking indicates that this product should not be disposed with other household waste. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>