VIVO STAND-V002K Pneumatic Arm Dual Monitor Desk Mount Instruction Manual
- June 7, 2024
- Vivo
Table of Contents
VIVO STAND-V002K Pneumatic Arm Dual Monitor Desk Mount
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED. DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Loosen the screws and disassemble the Clamp (D) using the 4mm Allen Wrench
(K).
STEP 2
OPTION A: Clamp Installation
Attach clamp brace (D1) to the Pole (C) using the M6x16 bolts (J) and the 4mm
Allen Wrench (K). Peel the protective film off of the Soft Pad (G) and place
it onto the clamp brace (D1).
OPTION B: Grommet Base Installation
For grommet hole attachment only, cut the Soft Pad (G) along the indentations.
Peel the protective film off of the Soft Pad (G) and place the pieces onto the
Grommet Base (F) as shown below.
OPTION A: Clamp Installation
For thinner desktops, re-attach the Clamp (D2) to the Clamp Brace (D1) and
tighten the screws using the 4mm Allen Wrench (K). For thicker desktops,
disassemble the Clamp (D2) using a Phillips screwdriver as shown in 3.1. Flip
the L-bracket over and reassemble. Then re-attach the Clamp (D2) to the Clamp
Brace (D1) and tighten the screws using the 4mm Allen Wrench (K).
OPTION B: Grommet Installation
If not using an existing through-hole, using a 10mm (⅜”) drill bit, drill
through the desktop at least 2” away from the edge. Disassemble the Clamp (D2)
using a Philips screwdriver. Set aside all parts except for Clamp Bolt (D3).
Attach Pole (B) and Grommet Base (F) to the desktop using the Support Plate
(H) and Clamp Bolt (D3) as shown below.
While holding Arm (A) closed, cut the shipping tie and gently release
(A).
STEP 3
Slide Arm (A) onto Pole (B) and tighten using 6mm Allen Wrench (L). Attach
Cable Clip (E) to Pole (C).
STEP 4
Attach VESA Plate (B) to the back of the monitor using Screws (M-A through
M-D) and Washers (M-E). If needed, use Spacers (M-F). 
STEP 5
Slide VESA Plate (B) with monitor over bracket on Arm (A). Secure using the
Thumbscrew (I).
STEP 6
Adjust gas spring support in Arm (A) using 6mm Allen wrench (L). Turning
counter-clockwise increases support, and clockwise decreases.
STEP 7
Remove bottom cover from Arm (A) by sliding it off. Organize cables and re-
attach cover.
STEP 8
Adjust tilt support using 6mm Allen Wrench (L). Store Allen Wrenches (K and L)
in Cable Clip (E). Adjust as desired. 
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer
immediate assistance with rapid response times. If any parts are received
damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
309-278-5303 AVG. RESOLUTION TIME
(within office hrs): 5M 4S
www.vivo-us.com AVG. RESOLUTION TIME (within office
hrs): < 15 M
help@vivo-us.com AVG. RESPONSE TIME (within office
hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr!logo
References
- Register a .US.COM domain today!
- Pneumatic Arm Dual Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>