ULINE H-1784/H-8152 Double Scissor Lift Tables User Manual
- June 7, 2024
- ULINE
Table of Contents
H-1784, H-8152
DOUBLE SCISSOR LIFT TABLES
1-800-295-5510
uline.com
TECHNICAL INFORMATION
| SPECIFICATIONS | H-1784 | H-8152 |
|---|---|---|
| Capacity | 770 lbs. | 1.760 lbs. |
| Height Raised | 51″ | 59′ |
| Height Lowered | 13.8′ | 18.7′ |
| Table Size | 36x 20 x2″ | 48 x 24 x2″ |
| Total Height | 30.3° | 37.91 |
| Overall Length | 42′ | 54″ |
| Foot Pedal Cycles to Max. Height | 46 | 70 |
| Wheel Diameter | 5″ | 6″ |
| Weight | 223 lbs. | 379 lbs. |
| Working Volume of 011 Cylinder | 310 ml | 180 ml |
| Oil Capacity | 400 ml | 275 ml |
GENERAL INFORMATION
- Read all instructions carefully before operating the lift table.
- DO NOT overload the lift table and always operate it within the rated load. Overloading will cause damage to the lift table and the operator.
- DO NOT stand or sit on the table to work.
- DO NOT put hands or feet under the table when lowering.
- Apply the brakes while loading to prevent the table from moving.
- The load must be distributed uniformly across the whole table.
- DO NOT load loose or unstable loads onto the table.
- DO NOT leave the table loaded for extended periods of time.
- DO NOT move the truck while lifting.
- The table should only be used on flat solid surfaces.
- Make sure not to overload the table when it is in the raised position. The safety valve only works as the table is lifted. Overloading in the raised position may damage the table.
- When loading and unloading goods in the raised position, do not drag loads across the table. This may cause offset loading and the table may turn over.
- When maintaining and repairing the table, the standing bar should be used to support the fork arm in order to prevent the table from falling. There should not be a load on the table while maintaining and repairing the table.
ASSEMBLY
The handle and foot lever are dismantled when shipped. They must be attached
to lift table before operating.
HANDLE INSTALLATION
Fix the handle (2) to the table body (12) with a flat washer (3), lock washer
(4), and bolt (5). Then tighten the bolt (5) with a wrench.
FOOT LEVER INSTALLATION
Insert the foot pedal (26) into the hole of the square bar (55). Fix the foot
pedal with a bolt (25), plain washer (56) a lock washer (57), and a nut (58).
Tighten the nut (58) with a wrench.
MAINTENANCE
It is very important to conduct necessary maintenance and upkeep so as to prolong the service life and safety of the lift table. Please check the lift table before operation accordingly:
- Check for any distortion or bending of any parts of the lift table.
- Check the brake of the truck and the condition of the wheels.
- Check for oil leakage in the hydraulic system.
- Add or fill lubricant to each friction surface before daily operation.
- If there is any failure, the lift table should be repaired at once before it can be put into use again.
- Change the hydraulic oil every twelve months, choose appropriate hydraulic oil according to the climate conditions.
- To change the hydraulic oil:
a. Unscrew the sealing screw with a wrench.
b. Lift the hand lever (2).
c. Twist off the screw of the oil plug and fill the pump with hydraulic oil.
TROUBLESHOOTING
| SPECIFICATIONS | H-1784 | H-8152 |
|---|---|---|
| Capacity | 770 lbs. | 1.760 lbs. |
| Height Raised | 51″ | 59′ |
| Height Lowered | 13.8′ | 18.7′ |
| Table Size | 36x 20 x2″ | 48 x 24 x2″ |
| Total Height | 30.3° | 37.91 |
| Overall Length | 42′ | 54″ |
| Foot Pedal Cycles to Max. Height | 46 | 70 |
| Wheel Diameter | 5″ | 6″ |
| Weight | 223 lbs. | 379 lbs. |
| Working Volume of 011 Cylinder | 310 ml | 180 ml |
| Oil Capacity | 400 ml | 275 ml |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>