ULINE S-21780 Digi-Day Electronic Scoreboard User Guide

S-21780, S-21781
DIGI-DAY® ELECTRONIC SCOREBOARD
1-800-295-5510
uline.com

OVERVIEW OF CONTROLS

DIGITAL DISPLAY
Power Loss Indicator

POWER LOSS INDICATOR
In the event of power loss, the display will go dark, yet hold in memory the number of days and time. When power is restored, there will be a n LED indicator and the display will resume normal operations. Time will shift back by the amount of power that was off. To reset the time of day and remove the power loss indicator, follow the procedure in step 3.

REMOTE CONTROL
All digital display functions require the use of remote control.
The remote control is programmed to control up to five different encoded digital displays. Whether the scoreboard has one or five displays, each can be controlled individually by following the “Connect Remote to the Digital Display” steps.

COUNTER INDICATOR ON HOLD
To pause a number of days, press the red HOLD button. There will be an LED indicator on the lower right, and the count will hold or freeze. To resume function, press the HOLD button. The LED indicator will turn off.

OPERATION

STEP 1
CONNECT REMOTE TO THE DIGITAL DISPLAY
Your remote has the capability to connect to five different digital displays.

• Press and hold CONNECT button (also labeled “1-5”) for approximately 3 seconds. The display(s) will flash the frequency number across all digits.
• Press the same number on the remote of the display you want to connect. The display will flash that number in segment 4, four times and resume normal operation (other displays will also return to normal operation).
• Your remote control is now connected to the selected digital display.

STEP 2
VERIFY COUNT UP FUNCTION
The scoreboard has the ability to either count up or down.

• Press the UP/DOWN button once to verify the correct model. In-display segment 1, the horizontal bar will be at the top for Count Up mode or at the bottom for Count Down mode.
• To change the Up/Down mode, press the UP/DOWN button.
•  After verifying, press ENTER button.

OPERATION CONTINUED

STEP 3
SET THE NUMBER OF COUNT DAYS

• Press the COUNT DAYS button. The first segment number will flash.
• Press the remote’s numbered buttons to enter the desired number of days. As each number is entered, the next segment will flash. After entering numbers, press ENTER button.

| Count Up mode is shown above.
---|---
| Count Down model shown above.

EXAMPLE: 357 days ­ Press COUNT DAYS button. Enter numbers 0-3-5-7 for a number of count days. Press ENTER button.

NOTE: The leading zero(s) will not appear during operation.

STEP 4
SET COUNT DAY TO CHANGE TO GREEN

• Press the GREEN DAY button. The first segment number will flash.
• Press numbered buttons to enter desired number count day to turn green (and subsequent numbers will always be green). As each number is entered, the next segment will flash.
• After entering numbers press the green ENTER button.

EXAMPLE: For 10 days, Press the GREEN DAY button. Enter 0-0-1-0 for the number of count days to change to green. Press ENTER button.
NOTE: Count Day(s) less than this number will be red.

NOTE: In this example, Count Day 1 through 9 will display in red. On Count Day 10 and beyond the display will be in green.

STEP 5
SET THE “ACTUAL TIME” OF DAY

• Press the ACTUAL TIME button. Colon dots appear and the first segment number will flash. The display operates on a 12-hour clock.
• Press the ACTUAL TIME button again to select AM and PM ­ bottom center LED indicator is green for AM and red for PM.
• Press the remote’s numbered buttons to enter the desired time. As each number is entered, the next segment will flash. After entering time, press ENTER button.

EXAMPLE: 9:15 AM time ­ press ACTUAL TIME button to turn LED indicator at the bottom center to be green, then enter numbers 0-9-1-5 for for actual time of day. Press ENTER button.
NOTE: During operation, when it is PM, the bottom center LED indicator will be red.

STEP 6
SET THE TIME FOR THE NUMBER OF COUNT DAYS TO CHANGE

• Press the COUNT TIME button. The top colon dot appears and the first segment number will flash. The display operates on a 12-hour clock.
• Press the COUNT TIME button again to select AM and PM ­ bottom center LED indicator is green for AM and red for PM.
• Press the remote’s numbered buttons to enter the desired time. As each number is entered, the next segment will flash. After entering time, press ENTER button.

EXAMPLE: 11:59 PM time ­ press COUNT TIME button to turn LED indicator at the bottom center to be red, then enter numbers 1-1-5-9 for time for a number of count days to change. Press ENTER button.

OPERATION CONTINUED

STEP 7
SET ACTUAL DATE

• Press the remote “Actual Date” (Calendar symbol) button. The year will appear and the first segment will flash.
• Press the remote’s numbered buttons to enter the desired year. As each number is entered, the next segment will flash. After entering the year, press ENTER button. The actual month and day date will appear with the bottom colon dot, and the first segment number will flash.
• Press the remote’s numbered buttons to enter desired month and date. As each number is entered, the next segment will flash. After entering the month and date, on the remote, press ENTER button.

EXAMPLE: November 14, 2017 date. Press the ACTUAL DATE button. Enter numbers 2-0-1-7, press ENTER button, enter numbers 1-1-1-4, press ENTER button.

STEP 8
DISPLAY FORMATS
TO DISPLAY:

• The NUMBER OF COUNT DAYS ONLY ­ Press the DAYS button. This displays only the count days.
• DATE ONLY ­ Press the DATE button. This displays only the month day.
• CLOCK ONLY ­ Press the CLOCK button. This displays only the actual time.
• ALL ­ Press ALL button. This displays the number of count days, date (month. day), and actual time in sequence each for 10 seconds.

STEP 9
COUNTING OPEN WORK WEEK DAYS
To only count actual workdays when the workplace is open, i.e. open 5 days and closed 2 days.

Determine the date for FIRST open workday after closed days ­ example: If only counting workdays Monday through Friday (and not counting Saturday and Sunday) the date for Monday would be the FIRST work date.
The FIRST work date must be a current or future date. If using a future date, OFF days will continue to calculate until that date occurs. It is best to set the work weekdays on the actual FIRST work date to avoid counting issues.

• Press the remote WORK DAYS button. The year will appear and the first segment will flash.
• Press the remote’s numbered button to enter the desired year. As each number is entered, the next segment will flash. After entering a year, press ENTER button. Month and day-date will appear with the bottom colon dot, and the first segment number will flash.
• This is to enter the FIRST date of the work weekdays. Press the remote’s numbered buttons to enter desired month and date. As each number is entered, the next segment will flash. After entering the month and date, press ENTER button. Single-digit will appear.
• This is the number of workdays for the display to count. Press remote’s numbered button, choice of 1 through 7. Afterward, the number will flash. Press ENTER button. This sets the specific number of workdays to count per week.

EXAMPLE: November 18, 2017, is the first day of the 5-day work week (only counting the working days). Press the WORKDAYS button. Enter number 1-1-1-8, press ENTER button, enter number 5, press ENTER button.

NOTE: Safe days counter doesn’t account for holidays or adjust the time for daylight savings time. Please update the display when the holiday or time change occurs.

1-800-295-5510
uline.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>